Sequential Trip - Bostitch SL1838BC-E Original Instructions Manual

Loading the plastic caps:
© Stanley Bostitch
1. Pull up on the pusher for the plastic disks. (Fig 6a)
2. Rotate the pusher out of the magazine. (Fig 6b)
3. Load the plastic disks (held together on a plastic pull string). (Fig 7)
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
4. Rotate the pusher back into the magazine. (Fig 8)
compliance for the products.
5. Pull up and completely remove the plastic pull string. (Fig 9)
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
"DIAL-A-DEPTH™" FASTENER CONTROL ADJUSTMENT (FIG 10)
rien que les produits soient conformes aux normes CE.
The DIAL-A-DEPTH™ Fastener Control adjustment feature provides close control of the fastener drive depth;
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
from flush with the work surface to shallow or deep countersink. First, set the air pressure for consistent drive in
die CE-Richtlinien für Produkte.
the specific work, then use the DIAL-A-DEPTH™ Fastener Control adjustment to give the desired depth of drive.
TRIGGER LOCKOUT CONTROL (Fig 11)
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
zeggen dat de producten voldoen aan de CE-vereisten.
The trigger lockout control feature on BOSTITCH pneumatic tools provides a trigger lock feature for added
safety control. Push the Lockout control button in or out to activate or lock the tool trigger.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
TRIP OPERATION MODE
produkterne.
Warning: Always disconnect air supply before making adjustments as accidental actuation may occur, possibly
causing injury.
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
yhdenmukaisuutta.
These models (SL1838BC-E) feature a selectable trigger system that allows the user to choose between the
following modes of operation:
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα αντίγραφα του παρόντος

SEQUENTIAL TRIP

εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
The sequential trip requires the operator to hold the tool against the work with the safety trip depressed before
pulling the trigger. In order to drive additional fasteners, the trigger must be released and the tool lifted away
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
from the work, before repeating the above mentioned steps. This makes accurate fastener placement easier,
conformità CE per i relativi prodotti.
for instance on framing, toe nailing and crating applications. The sequential trip allows exact fastener location
without the possibility of driving a second fastener on recoil, as described under Contact Trip (below). The
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
sequential trip tool has a positive safety advantage because it will not accidentally drive a fastener if the tool is
merking for produktet.
contacted against the work - or anything else - while the operator is holding the trigger pulled.
CONTACT TRIP
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
The common operating procedure on "Contact Trip" tools is for the operator to actuate the safety trip while
conformidade com a CE para os produtos.
keeping the trigger pulled, thus driving a fastener each time the work is contacted. This will allow rapid fastener
placement on many jobs, such as sheathing, decking and pallet assembly. All pneumatic tools are subject to
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
recoil when driving fasteners. The tool may bounce, releasing the safety trip and if unintentionally allowed to
conformidad con las normas CE de los productos.
re-contact the work surface with the trigger still actuated (finger still holding the trigger pulled) an unwanted
second fastener will be driven.
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
Warning: Tools must NOT be used in Contact Trip mode where changing from one working position to
another involves the use of ladders, stairs or similar structures such as roofs
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowią deklaracji zgodności CE prezentowanych produktów.
SELECTING THE TRIP MODE (Fig 12):
To ensure safety, the user should lock the trigger (see Trigger Lockout Control above) before changing the
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
trigger system. To change the trip mode, rotate the mode switch in the counterclockwise direction. The mode
stanowią deklaracji zgodności CE prezentowanych produktów.
switch will lock automatically when the indicating arrow is pointing down to the 3 nail icon stamped into the tool
frame (Contact Trip Mode) or to a single nail icon stamped in the tool frame( Sequential Trip Mode). Unlock the
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané trigger to resume tool operation.
výrobky.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
a termék CE-megfelelőségét.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.