Section 6 Adjustment Procedures; Preparation - Icom IC-F5061 Servise Manual

SECTION 6

6-1 PREPARATION

When adjusting IC-F5060 series transceiver, CS-F5060
er), RS-232C cable JIG cable (modifi ed OPC-1122/U
,
EQUIPMENT
Output voltage
DC power supply
Current capacity
Frequency range
modulation analyzer
Measuring range
Frequency range
Frequency counter Frequency accuracy
Sensitivity
Measuring range
RF power meter Frequency range
Impedance
SWR
▄ SYSTEM REQUIREMENTS
® ®
• Microsoft Windows 98/98SE/Me/2000/XP
▄ ADJUSTMENT SOFTWARE INSTALLATION
q Quit all applications when Windows is running.
w Insert the CD into the appropriate CD drive.
e Double-click the "Setup.exe" contained in the 'CS-F5060
ADJ' folder in the CD drive.
r The "Welcome to the InstallShield Wizard for CS-F5060
ADJ" will appear. Click [Next>].
t The "Choose Destination Location" will appear. Then click
[Next>] to install the software to the destination folder. (e.g.
C:\Program Files\Icom\CS-F5060 ADJ)
y After the installation is completed, the "InstallShield Wiz-
ard Complete" will appear. Then click [Finish].
u Eject the CD.
i Program group 'CS-F5060 ADJ' appears in the 'Programs'
folder of the start menu, and 'CS-F5060 ADJ' icon ap-
pears on the desk top screen.
▄ BEFORE STARTING SOFTWARE ADJUSTMENT
Clone the adjustment frequencies and settings into the transceiver, and set the confi guration using the CS-F5060
before starting the software adjustment. Otherwise, the software adjustment can not be started.
WARE
CAUTION!: BACK UP the originally programmed memory data in the transceiver before programming the adjustment frequencies.
When program the adjustment frequencies into the transceiver, the transceiver's memory data will be overwritten and
lose original memory data at the same time.
• ADJUSTMENT FREQUENCY LIST
CH FREQUENCY
1 154.900 MHz
2 174.000 MHz
3 136.000 MHz
4 155.000 MHz
5 136.000 MHz
6 136.000 MHz
7 155.000 MHz
8 155.000 MHz
9 136.000 MHz
*; [EUR] only
ADJUSTMENT PROCEDURES
CLONING SOFTWARE,
CLONING CABLE
GRADE AND RANGE
: 13.6 V DC [USA]
13.2 V DC [EUR], [EXP]
: More than 1.5 A
: DC–300 MHz
: 0 to ±10 kHz
: 0.1–300 MHz
: ±1 ppm or better
: 100 mV or better
: 0.1–60 W [USA]
0.1–30 W [EUR], [EXP]
: 100–300 MHz
: 50 Ω
: Better than 1.2 : 1
(for the ADJUSTMENT SOFTWARE)
• RS-232C serial port (D-sub 9 pin)
SETTING
• TX power : Low1
• Mode : Narrow
• TX power : Low1
• Mode : Wide
• TX power : Low1
• Mode : Wide
• TX power : Low1
• Mode : Wide
• TX power : High
• Mode : Narrow
• TX power : Low2
• Mode : Wide
• TX power : Low1
• Mode : Middle
• DTCS : 007
• TX power : Low1
• Mode : Narrow
• TX power : Low1
• Mode : Narrow
CS-F5060 ADJ
; see the page 6-2) and the following test equipments are required.
EQUIPMENT
Attenuator
External speaker
Standard signal
generator (SSG)
Oscilloscope
Digital voltmeter
▄ STARTING SOFTWARE ADJUSTMENT
q Connect the transceiver and PC with RS-232C cable and
JIG CABLE .
w Turn the transceiver power ON.
e Boot up Windows, and click the program group 'CS-F5060
ADJ' in the 'Programs' folder of the [Start] menu, then
CS-F5060 ADJ's window appears.
r Click 'Connect' on the CS-F5060 ADJ's window, then the
window shows transceiver's condition and adjustment
items as below.
t Set or modify adjustment data as specifi ed.
Microsoft and Windows are registered trademarks of Micro-
soft Corporation in the U.S.A. and other countries.
CH FREQUENCY
10 174.000 MHz
11* 155.000 MHz
12* 136.000 MHz
13* 174.000 MHz
14 155.000 MHz
15 136.000 MHz
16 174.000 MHz
17 136.000 MHz
18 136.000 MHz
6 - 1
(Rev. 1.0 or lat-
ADJUSTMENT SOFTWARE
GRADE AND RANGE
Power attenuation : 50 or 60 dB
Capacity : 60 W [USA]
30 W [EUR], [EXP]
: 4 Ω
Input impedance
Capacity : 5 W or more
: 0.1–300 MHz
Frequency range
: 0.1 µV to 32 mV
Output level
(–127 to –17 dBm)
Frequency rang : DC–20 MHz
Measuring range : 0.01–20 V
Input impedance : 50 kΩ
Measuring range : 0.1–10V
SETTING
• TX power : Low1
• Mode : Narrow
• TX power : Low1
• Mode : Middle
• TX power : High
• Mode : Middle
• TX power : Low2
• Mode : Middle
• TX power : Low1
• Mode : Digital
• TX power : Low1
• Mode : Digital
• TX power : Low1
• Mode : Digital
• TX power : Low1
• CTCSS : 151.4 Hz
• TX power : Low1
• Mode : Wide
• DTMF : P3
CLONING SOFT-