Initial Operation - Gardena FP 1000 E Operating Instructions Manual

are people in the water. Swimming pools and
garden ponds should be designed according
to international and national design regulati-
ons.
v Please consult a professional electrician.
For Austria :
Pumps for use on swimming pools and on
ponds may only be operated via an isolating
transformer.
v Please consult a professional electrician.
For Switzerland :
In Switzerland mobile appliances which are
used outdoors, must be connected via a resi-
dual-current device.
Note :
Do not allow the pump to run without water
because dry-running leads to an undesira-
ble build up of heat.
3. Assembly
Fit the pump : To provide a firmer mounting, the filter housing can be attached to
a solid base (e.g. paving stone).
1. Screw nozzle pipe
joint.
2. Screw the water feature insert you require (a / (b / (c / (d on
1
the nozzle pipe
2
All pumps
(a cascade
2
Holder for GARDENA underwater light art 7951
VARIANT 1 : Mount the addi- The additional filter can be fitted on the filter housing to extend the
tional filter on the pump: maintenance interval and to give the water feature a longer life.
1. Remove the cap
2. Fit both filter shells
place.
4
3. Press sealing cover
3
You can install additional filters
Additional filters are available from GARDENA Service.
5
10
Before operating the pump, look to see if there
is any damage of the pump (esp. regarding
power cable and plug). The connection cable
of the pump cannot be replaced. If the cable is
damaged the pump must be scrapped.
Do not use the power cable to carry the pump
or to pull the plug out of the socket. Protect
the power cable from heat, oil and sharp
edges.
The temperature of the liquid used must not
be below 4 °C or above 35 °C.
Sand and other abrasive substances in the
liquid cause increased wear and reduce the
output of the pump.
Please observe the local noise prevention
regulations.
1
on to the pump with the ball and socket
1
.
art. 7650 - 7654 art. 7655 - 7657
(b Waterbell (c jets of (d foaming -
water spring
3
from the pump.
4 5
on the filter housing and clip into
3 4
on to the additional filter .
to increase the filter surface.
VARIANT 2 : Mount the pond
The additional filter can be installed as a pond edge controller for
edge controller : adjusting water features and cleaning the filter housing from the
edge of the pond. Water is only drawn in via the additional filter.
You can connect the following hoses to the hose connection:
6
3 /4" and 1" for FP 750 E / FP 1000 E / FP 1400 E / FP 1800 E /
.
FP 2500 E
5
1 1/4" and 1 1/2" for FP 4000 E / FP 5000 E / FP 7500 E
.
For best results use a hose with the largest possible diameter.
7
1. Remove the cap
2. Press in snap fastenings
open up the filter housing
3
3. Push the hose connection
on to the pump.
4. Close filter housing
5. Insert hose connection
7
to one filter shell
into the second filter shell
6. Press sealing cover
the pond edge control
7. Connect water feature pump
and pond edge control to a
hose.

4. Initial Operation

1. Place water feature pump on a firm base in such a way that the
Switch on water
filter housing
feature pump :
2. Pull telescopic pipe
3. Netzstecker in eine Wechselstromsteckdose einstecken.
Warning: Pump will start immediately.
4. Set the quantity of water required for the water feature using the
9
regulator
5. Water bell : Screw insert into the water feature until the water
feature has produced the shape required.
5
0
Start pond edge control : TIP : Install the pond edge controller on a bed of gravel to
improve the water intake. The regulating valve
open when using the pond edge controller.
9
A 1. Fill hose with water to remove any cushions of air in the hose.
2. Secure the pond edge controller at the edge of the pond (using
rocks, for example).
5
0
The pond edge control must be completely covered with water.
3. Set the quantity of water required for the water feature with the
regulator
3
from the pump.
6
and
5
.
7
4
5
.
8
in
4
and snap
4
.
3
3
on to
4
.
5
is completely covered by water.
9
out to the desired length.
0
.
0 must be fully
A
.
8
11