Black & Decker BDPE400 Manual page 4

ENGLISH
Additional safety instructions for non-rechargeable
batteries
@
Warning! Batteries can explode or leak, and can
cause injury or fire. Observe the instructions as
described below.
Ensure the switch is in the off position before inserting bat-
u
teries. Inserting batteries into power tools and appliances
that have the switch on invites accidents.
Under abusive conditions, liquid may be ejected from
u
the battery; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation or burns.
Carefully follow all instructions and warnings on the bat-
u
tery label and package.
Always place batteries correctly according to the polarity
u
(+ and -) as marked on the battery and the product.
Do not short-circuit the battery terminals.
u
When battery/battery pack is not in use, keep it away from
u
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a con-
nection from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
Do not attempt to charge non-rechargeable batteries.
u
Do not mix old and new batteries. Replace all of them at
u
the same time with new batteries of the same brand and
type.
Keep batteries out of reach of children.
u
Remove batteries if the product will not be used for
u
several months.
Never attempt to open for any reason.
u
Do not store in locations where the temperature may
u
exceed 40 °C.
When disposing of batteries, follow the instructions given
u
in the section "Protecting the environment".
Do not incinerate the batteries.
u
Do not expose the batteries to heat
u
Features
This appliance includes some or all of the following features.
1. Paint applicator
2. Speedy Edge main body
3. Paint reservoir syringe
4. Plunger drive
5. Trigger
6. Flow control knob
7. Battery cap
8. Fill sleeve
4
(Original instructions)
Assembly
Fitting the batteries (fig. A)
Remove the battery cap (7) by pressing in the tabs (9) and
u
then sliding the battery cap (7) off the handle.
Insert 3 AA (LR06 - Alkaline) batteries into the handle.
u
Refit the battery cap (7) by sliding it back on to the handle.
u
Note: Always place batteries correctly according to the polar-
ity (+ and -) as marked on the battery and the product.
Fitting the paint applicator (fig. B)
Press in the paint applicator release tabs (10).
u
Slide the paint applicator into the front of the main body
u
(2) of the Speedy Edge.
Release the tabs (10).
u
Note: The paint applicator can not be fitted with the paint
reservoir syringe in place.
Removing the paint applicator (fig. B)
Press in the paint applicator release tabs (10).
u
Slide the paint applicator out of the main body (2) of the
u
Speedy Edge.
Release the tabs (10).
u
Note: The paint applicator can not be removed with the paint
reservoir syringe in place.
Fitting the paint reservoir syringe (fig. C - E)
Note: The paint reservoir syringe can not be attached until the
paint applicator has been fitted
Pull the plunger drive (4) to the back of the main body of
u
the Speedy Edge and clip it in place.
Slide the paint reservoir syringe (3) into the main body of
u
the Speedy Edge.
Pull the plunger drive (4) back and up to release it then
u
gently guide the plunger drive tip (11) into the recess (12)
in the back of the plunger (13) .
Removing the paint reservoir syringe (fig. C - E)
Pull the plunger drive (4) to the back of the main body of
u
the Speedy Edge and clip it in place.
Slide the paint reservoir syringe (3) out of the main body
u
of the Speedy Edge.
Use
Filling with paint
Note: Wear disposable gloves to keep your hands clean.
Slide the paint reservoir syringe (3) into the fill sleeve (8).
u
Lower the tip of the fill sleeve (8) into the paint.
u
Fill the paint reservoir syringe (3) by slowly pulling back
u
the plunger (13).