Page 1
PURE CYCLING BICYCLE MANUAL SPEEDMAX CF SLX These are additional instructions for the Canyon Speedmax CF SLX. Always refer to the Canyon Your bicycle and this manual comply with the safety requirements of the EN ISO bicycle manual road bike as well. Important: Assembly instructions page 7. Read pages 2-6 standard 4210-2.
These are additional instructions for the Canyon Speedmax CF SLX. The chapters of this table of contents printed in black refer to your Canyon Speedmax CF SLX; there is no supplementary information in the Canyon bicycle manual road bike. The chapters of this table of contents printed in grey imperatively require that you refer to the Canyon road bicycle manual.
Canyon a complete bicycle from the Canyon frameset. propriate equipment. At the very least you Speedmax CF SLX and that they do not nec- should wear a properly adjusted bike helmet, additional instructions and the bicycle manu- al road bike and then essarily apply to other bikes.
Do not use the und -Sicherheit GmbH tracts or with electronical systems or used for Canyon bikes are not approved in Canyon road bike on a bicycle trainer to www.zedler.de other business purposes without prior written general for mounting child carriers.
Canyon Speedmax CF SLX and ask a sembly or insufficient servicing can render dent on your new Speedmax CF SLX, carry out helper to assist you in unpacking it from To do this, only use a box cutter or a similar the racing machine unsafe.
Page 6
USING THE CANYON TORQUE WRENCH USING THE CANYON ASSEMBLY PASTE OF THE CANYON SPEEDMAX CF SLX Your Canyon Speedmax CF SLX IS fully fac- tory assembled and a test run was made. The bicycle should be fully functional without any...
Page 7
Prior to applying Canyon assembly paste, remove dirt particles and lubricant residues from the surfaces to be treated. Apply a thin and even film of Canyon assembly paste to the cleaned surfaces using a brush or a chamois. Mount the components, as specified. Use the Canyon torque wrench and never exceed the prescribed maximum torque value.
Page 8
Apply a little Canyon assembly paste to the and up to the MAX marking of the seat post. fastened to the handlebars with special bottom part of the seat post and inside the straps with Velcro fastener.
Page 9
2 Nm. Assemble your Canyon using the Canyon torque wrench enclosed with the BikeGuard.
Page 10
ASSEMBLY FROM THE BIKEGUARD ASSEMBLY FROM THE BIKEGUARD FRONT WHEEL MOUNTING Make sure the spacers are correctly aligned, Position the armrest in centred position on Insert the quick-release into the hollow front Take the front wheel and take off both protec- i.e.
Page 11
ASSEMBLY FROM THE BIKEGUARD ASSEMBLY FROM THE BIKEGUARD MOUNTING THE PEDALS The brakes are state-of-the-art in aerody- Tighten up the counternut of the quick - Make sure the front wheel is accurately cen- Before mounting the pedals, check the mark- namics and therefore do not have a release release until the quick-release lever builds up tred between the fork blades.
Page 12
Screw each pedal manually into the thread of Fix the white reflector to the handlebars and On the Canyon Speedmax CF SLX the Di2 Check the proper functioning of the gears. its crank by two to three full turns. Continue...
SPECIAL FEATURES OF TRIATHLON BIKES AND TIME TRIAL MACHINES SPECIAL FEATURES OF TRIATHLON BIKES AND TIME TRIAL MACHINES Your Canyon Speedmax CF SLX is equipped with special aerobars for triathlon and time trial races, which must be performed in a par- ticularly aerodynamic seating position.
The control buttons transmit the shifting command to the rear derailleur via the cable In addition, only use pad holders from Canyon! (Di2). Then the rear derailleur swivels, caus- ing the chain to climb onto the next sprock- Carbon brake pads usually wear down faster et.
SPECIAL FEATURES OF CARBON WHEELS ADJUSTING THE CANYON SPEEDMAX CF SLX TO THE RIDER The brake surfaces of the carbon rims are ADJUSTING THE sensitive to heat. Therefore, when you are rid- CANYON SPEEDMAX ing in the mountains, avoid any drag braking.
ADJUSTING THE CANYON SPEEDMAX CF SLX TO THE RIDER ADJUSTING THE CANYON SPEEDMAX CF SLX TO THE RIDER Align the handlebars such that you still have Sit on the saddle and put one heel on the ped- your Canyon Speedmax CF SLX fully under al at its lowest point.
ADJUSTING THE CANYON SPEEDMAX CF SLX TO THE RIDER ADJUSTING THE CANYON SPEEDMAX CF SLX TO THE RIDER FORE-TO-AFT-POSITION AND SADDLE TILT The fore-and-aft position of the saddle can be Slide the seat post in the seat tube to the de-...
ADJUSTING THE CANYON SPEEDMAX CF SLX TO THE RIDER ADJUSTING THE CANYON SPEEDMAX CF SLX TO THE RIDER ADJUSTING THE HEIGHT OF THE HANDLEBARS If the adjustment range is still not sufficient, As a further option, the saddle clamping bolts...
ADJUSTING THE CANYON SPEEDMAX CF SLX TO THE RIDER ADJUSTING THE CANYON SPEEDMAX CF SLX TO THE RIDER ADJUSTING EXTENSIONS AND ARMRESTS In case you want to mount the extensions at If necessary, also replace the threaded The Canyon Speedmax CF SLX is available...
Page 20
ADJUSTING THE CANYON SPEEDMAX CF SLX TO THE RIDER ADJUSTING THE CANYON SPEEDMAX CF SLX TO THE RIDER Use the narrow red terminating rings between The armrests can be mounted lengthways in Check the firm seat of the armrest and change Finish by fixing the pads with the Velcro fas- the top spacer and the armrest.
ADJUSTING THE CANYON SPEEDMAX CF SLX TO THE RIDER ADJUSTING THE CANYON SPEEDMAX CF SLX TO THE RIDER REPLACING EXTENSIONS SHORTENING THE EXTENSIONS Take the new extension in your hand and guide Do not blow away the chips and dust pro-...
ADJUSTING THE CANYON SPEEDMAX CF SLX TO THE RIDER ADJUSTING THE TRAIL OF THE FORK ADJUSTING THE TRAIL OF THE FORK After sawing carbon extensions seal the cut end with two-component adhesive (epoxy resin), clear lacquer or superglue. All in all, you can choose between three po-...
Canyon. Canyon 30 to 50 times to around 30 km/h the brake ineffective. Risk of an accident! due to their width. Risk of an accident!
Page 24
Pay atten- plied original brake pads only or, if another brake pads and the rim sides is approx. 1 to new brake pads (from Canyon!). tion to the correct orientation. Tighten the wheel type was mounted, with brake pads 1.5 mm on each side.
THE BRAKE SYSTEM THE BRAKE SYSTEM REAR BRAKE Mount the new brake pad together with the Always tighten the clamp bolts of the brake Correct the position of the cable holder, if Unscrew the clamp bolts of the brake cover brake pad holder as well as the spacers and pad holders to the indicated torque value of and remove the brake cover.
Page 26
Once the position of the cable holder is cor- new brake pads (from Canyon!). the same order and orientation as removed rect, check whether the gap between the previously.
NOTES ON REPLACING THE WHEELS THE HEADSET Check the adjustment of the brakes as de- If your Speedmax CF SLX makes knocking In the case of the integrated headset of the If you want to mount wheels of different rim...
4 Nm. tions, this may be necessary to observe the should, therefore, be left to a skilled me- provisions for the horizontal saddle position. chanic. If in doubt, ask an expert to adjust your Canyon Speedmax CF SLX.
Page 29
ADDITIONAL ACCESSORIES ADDITIONAL ACCESSORIES TOOLBAG REPLACING THE SEAT POST SWITCH PLATE KIT Undo the two Allen bolts which clamp the sad- Under the tool-free removable top tube cover If you want to exchange the standard seat With the “Switch Plate Kit” you can shift the there is a small bag containing all necessary post against the “TT”...
Page 30
ADDITIONAL ACCESSORIES ADDITIONAL ACCESSORIES ANGLED SPACER KIT Insert further threaded sleeves from below Insert the “Team” spacers directly under the With the “Angled Spacer Kit” you can change If necessary, use the supplied shorter thread- into the offset spacers and mount further armrests and fasten the spacers with the the inclination of the extensions and the arm- ed sleeves and clamp bolts and observe the...
ADDITIONAL ACCESSORIES WARRANTY AND GUARANTEE GARMIN MOUNT WARRANTY Your bike was manufactured with care and delivered to you largely preassembled. We are obliged by law to guarantee that your bike is free of any defects which considerably reduce its value or fitness for use or make it worthless or useless.
The brake pads of rim brakes are subject to latest when you are through your second set Canyon road, time trial, triathlon or wear due to their function. If you use your of brake pads.