25 % - 95 % (non-condensing) Weighing plate dimensions 230 x 190 (stainless steel) (mm) Casing dimensions 230 x 300 x 130 Total dimensions mounted 230 x 300 x 130 (mm) Weight kg (net) IP65 IP protection (Only during operation on battery power) FFN-N-BA-e-1323...
Page 5
25 % - 95 % (non-condensing) Weighing plate dimensions 230 x 190 (stainless steel) (mm) Casing dimensions 230 x 300 x 130 Total dimensions mounted 230 x 300 x 130 (mm) Weight kg (net) IP protection IP65 (Only during operation on battery power) FFN-N-BA-e-1323...
2 Appliance Overview 2.1 Overview of displays 2.1.1 Not verifiable models 2.1.2 Verifiable models FFN-N-BA-e-1323...
Page 8
Icon is glowing for power supply via power pack Display weighing unit kg Displayed weight in kg Display weighing unit lb Displayed weight in lb (only in not verifiable units) Display weighing unit g Displayed weight in g (only in verifiable units) FFN-N-BA-e-1323...
ON/OFF-switch Turn on/off TARE button Tare balance Call up menu Change to the next menu item /parameter Zero setting key Balance set at zero Select menu item / parameter TARE + ZERO-key Change units FFN-N-BA-e-1323...
Information is available on KERN’s home page (www.kern-sohn.com with regard to the monitoring of balance test substances and the test weights required for this. In KERN’s accredited DKD calibration laboratory test weights and balances may be...
4.1 Pay attention to the instructions oft the Operation Manual Carefully read this operation manual before setup and commissioning, even if you are already familiar with KERN balances. Versions in other languages are non-binding translations. The only binding version is the original document in German.
Avoid static charge of goods to be weighed or weighing container. Major display deviations (incorrect weighing results) may be experienced should electromagnetic fields (e.g. due to mobile phones or radio equipment), static electricity accumulations or instable power supply occur. Change location or remove source of interference. FFN-N-BA-e-1323...
Carefully remove the balance from the packaging, remove plastic cover and setup balance at the intended workstation. 1 Weighing plate 2 Locking screw 3 Carrier weighing plate 4 Display 5 Bubble level 6 Keyboard 7 Footscrews 8 Rechargeable battery compartment cover 9 Screws of battery compartment cover FFN-N-BA-e-1323...
Page 14
Pressure compensation Mains connection screw Battery compartment Pressure compensation screw: On the lower side of the balance there is a pressure compensation screw [1] which has to be opened for the weighing process. Fasten the screw before cleaning the balance. FFN-N-BA-e-1323...
In the menu you can activate the AUTO-OFF function time off], see chap. 9.3. According to menu settings, the balance switches automatically off in order to spare the battery. Insert rechargeable battery: Remove any adherent moisture from the balance Move both levers 90° to the left FFN-N-BA-e-1323...
Page 16
Connecting the rechargeable battery Watch the colours: Red on red ! Black on black! Insert the rechargeable battery in a manner that it cannot slip (fasten with a rubber mat) Ensure that the cables are not squeezed. FFN-N-BA-e-1323...
6.3.1 Mains connection during rechargeable battery operation During the rechargeable battery operation ensure that the mains connection is covered with a rubber cap. Only by this the type of protection IP65 is ensured. FFN-N-BA-e-1323...
1 “Techn. data”). The accuracy of the weight used for adjustment has to correspond approximately to readability d of the scale, or rather closer than that. Info about test weights can be found on the Internet at: http://www.kern-sohn.com Procedure when adjusting: Observe stable environmental conditions.
(Example) Enter value for adjustment weight (See chpt 1) by Position weight Press Remove weight whilst scale is carrying out self-test Weighing scale changes to zero display. This completes the adjustment process. FFN-N-BA-e-1323...
(see chapter 1) Place the adjustment weight Press While the balance carries out a self-test, take away the adjustment weight The balance changes over to zero display. Now the process of adjustment is completed. FFN-N-BA-e-1323...
The seal marks attached on verified balances point out that the balance may only be opened and serviced by trained and authorised specialist staff. If the seal mark is destroyed, verification looses its validity. Please observe all national laws and legal regulations. In Germany a re-verification will be necessary. FFN-N-BA-e-1323...
After a verification the balance is sealed at the indicated positions. Position of the official seals: 1. Verification wire fastening 2. Verification wire fastening 3. Self-destroying seal mark 4. Cover of adjustment switch 5. Adjustment switch 6. Self-destroying seal mark FFN-N-BA-e-1323...
Place goods to be weighed in the weighing container. The net weight of the goods to be weighed is displayed. The weight of the weighing container will be displayed as a minus number after removing the weighing container (= gross weight). FFN-N-BA-e-1323...
8.4 Background illumination Press for approx. 3 seconds, „bK-AU“ will be displayed. Press to select background illumination automatically off („bK-AU“) and background illumination off („bK-oF“). Press to confirm selected setting. The balance changes into weighing mode FFN-N-BA-e-1323...
While the balance carries out a self test, press keep pressed until „F1 CAL“ appears Use to change to the next menu item Select menu item using Use to change between the individual parameters Select the desired parameter using FFN-N-BA-e-1323...
Menu item Function Calibrate not documented not documented not documented Auto-OFF function, adjustable between off, 3, 5 and 15 minutes not documented Multi-Tare function: 0 tare Multi-Tare function disabled P tare Multi-Tare function enabled not documented Return to weighing mode FFN-N-BA-e-1323...
Select the desired parameter using “F5 oFF“ appears, now the function is enabled Press repeatedly until “bACK“ appears Press The balance carries out a restart and changes to weighing mode FFN-N-BA-e-1323...
“F8 tn“ appears, now the function is enabled Press repeatedly until “bACK“ appears Press The balance carries out a restart and changes to weighing mode Now you have the ability to tare several times in a row. FFN-N-BA-e-1323...
Unload the balance; check if the weighing is correctly placed and screwed on Avoid air draughts / air Displayed weight is movement as well as permanently changing vibrations of the table and of the floor Unload the balance and Overload adjust again FFN-N-BA-e-1323...
The balance is on an uneven surface. Electromagnetic fields / static charging (choose different location/switch off interfering device if possible) Should other error messages occur, switch balance off and then on again. If the error message remains inform manufacturer. FFN-N-BA-e-1323...
Spilled weighing goods must be removed immediately. 12.2 Service, maintenance The appliance may only be opened by trained service technicians who are authorized by KERN. Before opening, disconnect from power supply. 12.3 Disposal Disposal of packaging and appliance must be carried out by operator according to valid national or regional law of the location where the appliance is used.
EN 60065:2002+A1:2006 Datum 08.04.2013 Signatur Date Signature Ort der Ausstellung 72336 Balingen Albert Sauter Place of issue KERN & Sohn GmbH Geschäftsführer Managing director KERN & Sohn GmbH, Ziegelei 1, D-72336 Balingen, Tel. +49-[0]7433/9933-0 Fax +49-[0]7433/9933-149, E-Mail: info@kern-sohn.com, Internet: www.kern-sohn.com FFN-N-BA-e-1323...