ICON pro-form 690 HR User Manual page 5

PART LIST—Model No. PFEVEL4986.0
Key No. Qty. Description
1 1 Base
2 1 Frame
3 1 Upright
4 1 Upright Endcap
5 1 Console
6 1 Front Stabilizer
7 1 Rear Stabilizer
8 1 Left Handlebar
9 1 Right Handlebar
10 2 Handlebar Endcap
11 1 Left Upper Body Arm
12 1 Right Upper Body Arm
13 1 Left Pedal
14 1 Left Pedal Leg
15 1 Right Pedal
16 1 Right Pedal Leg
17 2 Upright Cover
18 1 Left Front Handlebar Cover
19 1 Left Rear Handlebar Cover
20 1 Right Front Handlebar Cover
21 1 Right Rear Handlebar Cover
22 1 Water Bottle Holder
23 2 Front Stabilizer Endcap
24 2 Rear Stabilizer Endcap
25 2 Wheel
26 1 Base Foot
27 2 Leveling Foot
28 1 Left Side Shield
29 1 Right Side Shield
30 6 Upper Body Bearing
31 4 Pedal Leg Cover
32 2 Pedal Leg Axle
33 4 Pedal Leg Bearing
34 1 Base Axle
35 2 Base Bushing
36 2 Crank Arm
37 2 Inner Crank Cover
38 2 Crank Hub
39 1 Pulley Spacer
40 1 Pulley
41 2 Crank Bushing Cover
42 4 Crank Arm Bearing
43 2 Crank Bushing Sleeve
44 2 Crank Bearing Set
45 1 Crank
46 1 Crank Spacer
47 2 Crank Snap Ring
48 1 Upper Wire Harness
49 1 Lower Wire Harness
50 1 Reed Switch/Wire
R0907A
Key No. Qty. Description
51 1 Belt
52 1 Flywheel
53 1 "C" Magnet
54 1 Pillow Block
55 1 Magnet
56 1 Spring
57 1 Idler
58 1 Idler Bracket
59 1 Clamp
60 1 Reed Switch Bracket
61 1 Base Pin
62 2 Latch Bracket Spacer
63 2 Hairpin Cotter
64 1 Latch Bracket
65 1 Pivot Bracket
66 2 Pivot Bracket Spacer
67 1 Frame Pin
68 1 Latch Button
69 1 Roll Pin
70 1 Motor
71 1 Resistance Cable Pulley
72 1 Resistance Cable Set
73 2 Foam Grip
74 1 Pivot Axle
75 2 Hub Cover
76 2 Outer Crank Cover
77 2 Flywheel Bracket
78 4 M8 x 41mm Button Bolt
79 7 M8 Jamnut
80 1 M8 x 69mm Button Bolt
81 4 M10 Nylon Locknut
82 2 M10 x 80mm Carriage Bolt
83 2 M10 x 127mm Button Screw
84 6 M8 x 23mm Button Screw
85 1 M6 x 10mm Button Screw
86 2 Crank Screw
87 8 Hub Screw
88 10 M8 Washer
89 2 M10 x 60mm Button Screw
90 3 M8 Split Washer
91 1 Flywheel Spacer
92 1 Flywheel Washer
93 1 Flywheel Snap Ring
94 4 Pillow Block Screw
95 1 Stop Screw
96 1 M8 x 35mm Screw
97 1 "E" Clip
98 4 Pulley Screw
99 2 Crank Washer
100 2 M4 x 25mm Screw
20
ASSEMBLY
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the
included hex keys, assembly requires a phillips screwdriver
wrench , and a rubber mallet
As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parentheses
below each drawing is the key number of the part, from the PART LIST on pages 20 and 21. The number follow-
ing the parentheses is the quantity needed for assembly. Note: Some small parts may have been preassem-
bled. If a part is not in the parts bag, check to see if it has been preassembled.
Star Washer M8 Split Wave Washer
(111)–2
(112)–8
Washer (90)–3
M4 x 14mm M4 x 16mm
Screw (104)–8 Round Head
Screw (101)–8
Bearing Spacer
(118)–4
M8 x 23mm Shoulder
Hub Screw (87)–8
Screw (115)–4
M8 x 69mm Button
Bolt (80)–1
M10 x 127mm Button Screw (83)–2
Transport Handle
Screw (117)–4
, an adjustable
.
M8 Washer M8 Jamnut M10 Nylon
(88)–6 (79)–5 Locknut (81)–2
M4 x 32mm M4 x 45mm
Round Head Screw (108)–2
Screw (105)–6
M8 x 23mm Button M8 x 41mm Button
Screw (84)–4 Bolt (78)–4
M10 x 80mm Carriage
Bolt (82)–2
5