Gem-Rp1Cae2 Keypad - NAPCO Gemini GEM-X255 Programming Instructions Manual

!
Page 6
A. GEM-RP1CAe2 Keypad
To create your customized default program using a GEM-RP1CAe2 keypad, enter the following
GEMINI
SYSTEM ARMED AI #ZN=08 #KP=1 # OF ZONES IN AREA 1
A2 #ZN=00 #KP=0
01/01/97 12:00AM
ENTER # ZONES X X parameters. In each of the following steps, press the
NEXT/YES
A 1 2 3 E
D
PRIOR/NO
B 4 5 6 F
button to go forwards, the PRIOR (
AR EA
C 7 8 9 0 G
COMPUTERIZED SECURITY SYSTEM
R
button twice to exit at any time.
#OF ZNS IN AREA1
ENTER # ZONES 08
(Direct Entry)
#OF ZNS IN AREA2
ENTER # ZONES 00
(Direct Entry)
Note: The GEM-X255 is limited to a maximum of 96 zones and 15 keypads. All 96 zones and 15 keypads may be
programmed in the EZ Program Mode. For larger systems, refer to the PCD-Windows downloader.
F I R E Z O N E S
ENTER ZONE # 00
(Direct Entry)
NOTE: If you are programming a 2 Area system, enter the zone number of zones required for Areas 1 & 2. All fire zones
are common to areas 1 and 2. The Direct Address Program Mode can then be used to customize them as needed. See
Zone Options.
2 - W I R E F I R E Z N S
E N T E R Z O N E # 0 0
(Direct Entry)
have been designated as Fire Zones can be programmed as 2 Wire Fire zones. Press NEXT (
NOTE: JP7 must be set to "2-WF" position for 2-wire fire zones 7 and 8 (refer to Installation Instructions).
REPORT ALL ZONES
TO CENTRAL? Y/N
(Press YES or NO)
X
GEM-X255 Programming Instructions
) button to go backwards, the
F
Total Number of Zones in Area 1 & Area 2 (Appears for New Panel Only)
Directly enter the total number of zones to be programmed for Area 1 and
Area 2, respectively. Valid entries are from 01 to 96. Directly enter the total
number of zones, including leading zeros. Use number buttons
through . NOTE: Press the
9
based on groups of 4 zones each (after the first 8 zones), and will
automatically round up to the next group of 4. For example, if you enter 18,
it will automatically convert this to 20 zones. Press
( ) button to proceed.
E
Fire Zones (Appears for New Panel Only)
Enter the zone number of any Fire Zones (both 2-wire, 4-wire or wireless).
Valid entries are from 01 to 96. Directly enter each zone number, including
leading zeros, and press
zone(s). Press NEXT (
E
2-Wire Fire Zones (Appears for New Panel Only)
Enter the zone number of any Fire Zones (from previous question) which are
to be used with 2-wire smoke detectors. The only valid entries are 01 through
08. Directly enter each zone number, including leading zeros. Press
save, and then repeat for any additional zone(s). NOTE: Only zones which
Local System or C.S. Reporting System (Appears for New Panel Only)
Press YES ( ) button for all zones to report; press NO (
E
for no zones to report (LOCAL SYSTEM).
button to set cursor, the NEXT (
A
J
button to save and the
button for a zero. The system is
0
J
J
to save, and then repeat for any additional
) button to proceed.
E
L
NAPCO Security Systems
WI1092B 9/02
)
E
C
1
to save. Press NEXT
J
to
) button to proceed.
) button
F