Robomow RC304 Original Operating Instructions page 38

Screen Setting
Child Lock
P010
(Default = )
OFF
Anti-Theft /
Disabling Device
P011
(Default = OFF )
Anti-Theft /
Disabling Device
P012
Change PIN code
Base Station
P013
(Default = )
ON
Add Separated
P014
Zone
Remove Zone
P015
Sound
P016
(Default = )
ON
Mobile
Communication
P017
System
(Default = )
OFF
Statistics (Default
P018
= OFF )
Bluetooth Remote
P019
Control Pairing
Last Termination
P020
Event
Program On/Off
P021
(Default = )
ON
• The Child Lock feature locks the buttons to prevent unintended
operation, especially by children and pets.
• If the Child Lock is set to 'On', to operate the mower it is required to
first press one of the operating mode buttons and then to press the
OK button to confirm.
• The Anti-Theft / Disabling Device feature alarms the surroundings
in the event of an unintended use or removal of the mower from its
designated area.
• To turn the Anti-Theft / Disabling Device On for the first time, set it to
'On' and choose a PIN code of 4 digits.
Tip: Select a number you can remember. Write it down (bottom of
Chapter 10), and keep it in a safe place.
• When the Anti-Theft / Disabling Device system is activated, 0000 will
be displayed. Enter your 4-digit code to deactivate the Anti-Theft /
Disabling Device.
• If the code is not entered, then the message is changed to U062
(Alarm will soon be activated). Enter the code, otherwise the alarm
will start.
• Allows changing of the Anti-Theft / Disabling Device PIN code.
• Enter a new code and then re-enter the new code for confirmation.
• This option should be used in a Separated Zone which has a
Base Station
• If you have defined more than one zone, then select the relevant
zone before changing the setting.
• Enables the addition of a Separated Zone.
• L2 is displayed for Separated Zone A – press OK.
• Scroll to set the area of the Separated Zone and press OK.
• Enables the removal of a Separated Zone or a Sub-Zone.
• Choose the Zone you want to remove and press OK.
• Use the Sound option to turn all non-safety sounds off.
• Enables remote communication with the mower using a GSM
Module Accessory, which can be purchased separately.
• For more information, refer to Section 12 – Accessories.
• This menu is displayed only if P018 is set to 'On'.
• Enables to send the operation statistics from the mower to the
manufacturer for diagnostics in case of problems.
• Enables the pairing process between your Robomow and
an outdoor Bluetooth Remote Control that is available as an
accessory (Refer to Paragraph 12 Accessories).
• Enables the Behavior View of the special display (may be required
by a Service Station)
• This menu enables or disables (pauses) Automatic Operation
either in the main zone ('L1'), one of the Sub-Zones ('A1/ A2/ A3/
A4') or in the entire lawn ('All').
• This menu is only relevant when the Automatic operation is
enabled on the Power Box (see chapter 7.3)
• When Program is set to Off in a particular zone, the mower will
skip the operation in that zone, but will continue to mow all the
other zones.
• Note! If Program is set to ON at least in one zone, the mower will
continue to mow the edge of the entire lawn at the beginning of
each mowing cycle, as described in Section 6.1.
Description Options
On / OFF
ON / OFF
1234
0000
/
On OFF
L2
100
L2 / L3
/ / /
A1 A2 A3
A4
On / OFF
On / OFF
/
On OFF
All
L1
A1 / A2 / A3 /
A4
On / OFF
37