To Prevent Unintentional Erasing; Status Of Card Access Led And P2 Card; Status Of Card Access Led And Sd Memory Card - Panasonic VARICAM LT Operating Manual

@ NOTE
t Do not remove the P2 card after inserting it, while it is being accessed, or being detected (card access LED flashing in orange). Otherwise, it may
result in a malfunction.
t [TURN POWER OFF] is displayed in the viewfinder screen or the center of the control panel or in the warning message area at the top left of each
output indicator, and a warning is displayed with the warning lamp, etc., when the P2 card being accessed is removed. Also, all card access LEDs
flash rapidly in orange. Turn off the power. (page 170)
t If the P2 card is removed while being accessed, clips on it may become irregular. Check the clips and restore them, if required.
t If the P2 card being formatted is removed, formatting of the P2 card is not guaranteed. [TURN POWER OFF] is also displayed in the viewfinder screen
or the center of the control panel or in the warning message area at the top left of each output indicator at this time. Turn off the power and then back
on again, and reformat the P2 card.

To prevent unintentional erasing

To prevent unintentional erasing of the recorded contents in the memory card, move the write protect switch on the memory card to the Protect side (or
the LOCK side).
@ NOTE
t Write-protect switch can be switched while the card is being accessed (during recording or playback), but does not take effect until accessing of the
card stops.

Status of card access LED and P2 card

Card access LED
Illuminated in orange
Flashing in orange
Flashing in orange rapidly
Flashing in green slowly
Off*
* [ERR] is displayed on the HOME screen. Confirm the content in the INFO screen.

Status of card access LED and SD memory card

Card access LED
Illuminated in orange
Flashing in orange
Flashing in orange rapidly
Flashing in green slowly
Off*
Chapter 4 Video Recording and Color Grading — Memory card
Write-protect switch
Recording target
Accessing card
The card is being recognized.
Card full
Write protect
Unrecordable card
Card not supported
Illegal format
No card
Unauthenticated card
Recording target
Accessing card
The card is being recognized.
Accessing card
Card full
Write protect
Unrecordable card
Card not supported
Illegal format
No card
Unauthenticated card
Write-protect switch
P2 card status
Reading/writing are both possible.
Reading/writing are currently being performed.
The P2 card is being recognized.
There is no free space on the P2 card. Reading only is possible.
The write-protect switch on the P2 card is at the Protect position. Reading
only is possible.
It cannot record with the recording format that is currently set. To record,
change the recording format or use the card that can record.
This card cannot be used on the camera. Replace the card.
The P2 card is not properly formatted. Reformat the card.
The P2 card is not inserted. The card is waiting to be recognized.
This is a P2 card that cannot be authenticated.
Unlock with the device the password was set if the CPS password is set.
SD memory card status
Reading/writing are both possible.
Reading/writing are currently being performed.
The SD memory card is being recognized.
Reading files from the SD memory card or writing files to the SD memory
card.
(Scene files/setup files/CDL/3D LUT/update files)
There is no free space on the SD memory card. Reading only is possible.
The write-protect switch on the SD memory card is at the Protect position.
Reading only is possible.
It cannot record with the recording format that is currently set. To record,
change the recording format or use the card that can record.
This card cannot be used on the camera. Replace the card.
The SD memory card is not properly formatted. Reformat the card.
The SD memory card is not inserted. The card is waiting to be
recognized.
This is a SD memory card that cannot be authenticated.
– 58 –