Panasonic VARICAM LT Operating Manual page 130

Item
[USER BOX H POS]
[USER BOX V POS]
[VF SDI FOCUS [EXPAND MODE]
ASSIST]
[EXPAND1 SW]
[- POS1]
[- VALUE1]
[EXPAND2 SW]
[- POS2]
[- VALUE2]
[FOCUS IN COLOR SW] Displays/hides the peaking function.
[- PEAKING VALUE]
[- COLOR SEL]
[- MONO]
[FOCUS SQUARES SW] Displays/hides the focus square function.
[MONO SW]
[FOCUS DISP]
[VF SDI EI ASSIST] [ZEBRA SW]
[- ZEBRA1 DETECT]
[- ZEBRA2 DETECT]
[- ZEBRA2]
[WFM SW]
[- TYPE]
Chapter 10 Menu Operations — Menu list
Sets the horizontal position of the center of the user box.
[−50] - [50]
f Factory setting: [0]
Sets the vertical position of the center of the user box.
[−50] - [50]
f Factory setting: [0]
Sets the enlargement display function mode.
[10SEC]: Disables the enlarged display function after 10 seconds have elapsed.
[HOLD]: Enables the enlarged display function.
[UNTIL REC]: Enables the enlarged display function until performing recording operation.
f Factory setting: [10SEC]
Switches display/hide of the enlargement display function 1.
[ON], [OFF]
f Factory setting: [OFF]
Adjusts the source signal position in an enlarged display.
[0] - [8]
f Factory setting: [4]
Adjusts the enlargement factor.
[x2], [x3], [x4]
f Factory setting: [x2]
Switches display/hide of the enlargement display function 2.
[ON], [OFF]
f Factory setting: [OFF]
Adjusts the source signal position in an enlarged display.
[0] - [8]
f Factory setting: [4]
Adjusts the enlargement factor.
[x2], [x3], [x4]
f Factory setting: [x2]
[ON], [OFF]
f Factory setting: [OFF]
Sets the peaking function mode.
[LOW], [MID], [HIGH]
f Factory setting: [MID]
Sets the peaking function color.
[RED], [GREEN], [WHITE]
f Factory setting: [RED]
Switches display/hide of the monochrome function when the peaking function is displayed.
[ON], [OFF]
The monochrome display function is enabled when [MONO SW] is set to [ON] even if this is set to [OFF],
and it will display with monochrome function.
The monochrome display function is enabled when this is set to [ON] even if [MONO SW] is set to [OFF],
and it will display with the monochrome function.
f Factory setting: [OFF]
[ON], [OFF]
f Factory setting: [OFF]
Switches enable/disable of the monochrome display function when [IN COLOR/SQ./MONO SW] is set to
[ON].
[ON], [OFF]
f Factory setting: [OFF]
Sets the unit for the focus distance display.
[Meter], [Feet]
f Factory setting: [Feet]
Sets if the zebra signal is superimposed or not to the output from the <VF SDI> terminal.
[ON], [OFF]
f Factory setting: [OFF]
Sets the detection level of zebra pattern 1.
[0%] - [109%]
f Factory setting: [80%]
Sets the extraction level of zebra pattern 2.
[0%] - [109%]
f Factory setting: [100%]
Enables/disables zebra pattern 2 and selects [SPOT].
[ON], [SPOT], [OFF]
f Factory setting: [OFF]
Displays/hides waveform monitor.
[ON]/[OFF]
f Factory setting: [OFF]
Sets the display format of the waveform monitor.
[Y], [YGBR]
f Factory setting: [Y]
– 130 –
Description of settings