Leuze IT 3800g Manual
  1. Manuals
  2. Brands
  3. Leuze Manuals
  4. Barcode Reader
  5. IT 3800g
  6. Manual

Leuze IT 3800g Manual

Hand-held barcode scanner
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
IT 3800g
4,5 - 12 V
DC
Hand-held scanner for barcodes
Large reading field for the detection of
codes
Robust trigger button
Built-in decoder
Read-display
TTL-RS 232, USB and PS/2 interface
Operating temperature from 0 through 50°C
Protection class IP 41
Accessories
TTL-RS 232-cable/ext for IT 4xxx
Part No. 501 04442
TTL-RS 232-cable/PIN 9 for IT 4xxx
Part No. 501 04586
PS/2-cable for IT 4xxx
USB-cable for IT 4xxx
Power supply unit for IT 4xxx
Part No. 501 03403
Support for IT 3800g
Part No. 501 07039
Leuze electronic GmbH + Co. KG
www.leuze.de
Dimensioned drawing
Electrical connection
for RS 232 cable / ext.
9-pin Sub-D
for RS 232 cable / PIN 9
for USB cable
for PS/2 cable
Mini DIN connector
Part No. 501 03409
Part No. 501 03404
Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730
Signal
SH
Shield
2
TXD
3
RXD
5
GND
7
CTS
8
RTS
5VDC
9-pin Sub-D
SH
2
3
5
7
8
9
USB type A
1
2
3
4
Mini DIN socket
1
-
2
2
3
3
4
4
5
-
6
6
-
1
-
5
Leuze
electronic
Hand-held barcode scanner
Connection for power
supply unit
SH
1
2
Signal
IT 3800g RJ41
Shield
TXD
RXD
GND
CTS
RTS
5VDC
Signal
IT 3800g RJ41
5VDC
Data -
Data +
GND
Signal
PC Data
NC
GND
5VDC
PC Clock
NC
KB Data
KB Clock
IT 3800g RJ41
2
6
5
4
9
8
7
2
6
5
4
9
8
7
7 + 3
10
2
4
IT 3800g RJ41
6
4
7
5
8
9
IT 3800g - 02

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IT 3800g and is the answer not in the manual?

Questions and answers

Related Manuals for Leuze IT 3800g

Summary of Contents for Leuze IT 3800g

  • Page 1 Power supply unit for IT 4xxx Part No. 501 03403 KB Data Support for IT 3800g Part No. 501 07039 KB Clock Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 IT 3800g - 02 www.leuze.de...

  • Page 2: Specifications

    Hand-held scanner for barcodes (standard range) Part No. Data transmission via config- IT 3800g 15E IT 3800g with TTL-RS 232, KBW and USB interface 501 07041 urable RS 232 interface. Or keyboard-wedge opera- tion via PS/2 or USB inter- face.

  • Page 3: Hand-Held Barcode Scanner

    The program can be used to make settings and transfer them to the hand-held scanner. The configuration can also be stored so that it can be reused at a later time. Further information on this can be found in the User's Guide for the IT 3800g. The standard applications are described and summarised below.

  • Page 4: Configuration For The Leuze Standard Protocol

    2. Successively scan the 4 barcodes shown below. Each read operation is confirmed by a beep. The IT 3800g is set to the following transmission parameters: RS 232 transmission with 9,600 baud, 8 data bits, 1 stop bit, no parity, prefix <STX>, terminators <CR><LF>.
  • Page 5 Attention! We recommend connecting the IT 3800g directly to a PC or to the MA 21 or MA 41… connector units. If connecting to other components, please note that a voltage level range of -12 … +12V is maintained on the data lines! Leuze electronic GmbH + Co.
  • Page 6 4. Successively scan the 3 barcodes shown below. Each read operation is confirmed by a beep. The IT 3800g is set to the following transmission parameters: RS 232 transmission with 9,600 baud, 8 data bits, 1 stop bit, no parity, terminators <CR><LF>.
  • Page 7 4. Successively scan the 4 barcodes shown below. Each read operation is confirmed by a beep. The IT 3800g is set to the following transmission parameters: RS 232 transmission with 9,600 baud, 7 data bits, 1 stop bit, even parity, terminators <CR><LF>.
  • Page 8 Connecting the IT 3800g to the PS/2 interface The operation of the IT 3800g in keyboard emulation mode is described in this section. A PC keyboard is emulated in this operating mode. The data which are read in are written directly to the currently activated program. Thus, the data can be processed further in all standard programs.
  • Page 9 Connecting the IT 3800g to the USB interface (keyboard emulation) The operation of the IT 3800g in keyboard-emulation mode on a USB port is described in this section. A PC keyboard is emulated in this operating mode. The data which are read in are written directly to the currently activated program. Thus, the data can be processed further in all standard programs.
  • Page 10 Connecting the IT 3800g to the USB interface (COM-port emulation) The operation of the IT 3800g as a serial interface on a USB port is described in this chapter. A COM interface is emulated in this operating mode. The data which are read in are sent to a new COM interface. The driver with which you emulate this COM interface can be downloaded from our homepage at www.leuze.de .

Table of Contents