Before Setting Surface Controls - Kenmore 790.3670 series Use & Care Manual

Before Setting Surface Controls

Assembly of the Surface Burner Heads, Burner Caps and Burner Grates (Porcelain Cooktop
models)
It is very important to make sure that all of the Surface Burner Heads, Surface Burner Caps and Surface Burner Grates
are installed correctly and at the correct locations.
1. Remove all packing tape from cooktop area. Remove all
Burner Caps and Burner Heads.
2. Discard all packing material located under Burner Heads (if
applicable).
3. To replace the Burner Heads & Caps, match the letters
located under center of Burner Caps with the letters located
inside Burner Heads (Figure 1).
4. Match Burner Skirts with Burner Heads and Burner Caps (see
Figure 1). Replace the Burner Heads and Caps on cooktop
(see Figure 2). Carefully align the Electrodes into slot or hole
of each Burner Head (Figure 3). Note: The Burner Heads
should sit flat on Cooktop Burner Skirts.
5. Place the removable oven vent cover over the fixed oven
vent cover.
6. Unpack Burner Grates and position on the cooktop.
REMEMBER — DO NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTER THE
GAS ORIFICE HOLDER OPENING. Always keep the Burner Caps and Burner Heads in place whenever the surface
burners are in use.
Assembly of the Surface Burner Heads, Burner Caps and Burner Grates (Ceramic Glass
Cooktop models)
It is very important to make sure that all of the Surface Burner
Heads, Surface Burner Caps and Surface Burner Grates are
installed correctly and at the correct locations.
1. Be sure to follow the Installation Instructions before installing
and using your new range.
2. Remove all packing tape from cooktop. Remove Burner Caps
and Burner Heads (See Figure 4).
3. Discard all packing material located under all Burner Heads (if
applicable).
4. To replace Burner Heads & Caps, match the letters located under
center of Burner Caps with the letters located inside Burner Head
(only positions A & F are marked with letters - See Figure 5).
Place all Burner Heads & Caps on the cooktop (See Figure 4)
while carefully aligning the Electrodes into slots or holes of the
Burner Heads (Figure 7). Note: The Burner Heads should sit flat
on Cooktop Burner Skirts.
5. Replace Bridge Burner Caps. These include one Bridge Burner
Center Cap (rectangular shaped) and the two Bridge Burner End
Caps (The Bridge Burner End Caps will fit either the front or rear
Bridge Burner Head locations). Make sure that the tabs located
under the Bridge Burner Caps fall into the slots located in the
Bridge Burner Head (See arrows in Figure 6) and that all the Bridge
Burner Caps lie flat and evenly on the Bridge Burner Head.
6. Unpack Burner Grates. NOTE: Do not force End Burner Grates
down on cooktop. Be careful to line up the 2 Grate Pins located
on each of the 2 End Burner Grates into the Pilot holes located
on top of the Burner Caps (See Figure 8). Position Burner
Grates on cooktop and check that all the Burner Grate legs lie
on the glass surface.
7. Place Center Burner Grate between the end Burner Grates.
REMEMBER — DO NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTER THE
GAS ORIFICE HOLDER OPENING. Always keep the Burner Caps and Burner Heads in place whenever the surface
burners are in use.
Figure 1
Figure 4
Bridge Burner Head
Figure 6
9
14.2K
9.5K
Figure 2
Electrodes must
align into slot or hole for each
Figure 3
Burner Head
Bridge
Figure 5
Burner
End
Cap
Bridge
Electrodes
Burner
must align into slot or hole
Center
for each Burner Head
Cap
Figure 7
Bridge
Burner
End
Cap
Figure 8
5K
16.2K
Grate Pin
Burner
Cap
Pilot hole