Table of Contents
Advertisement
Available languages
Available languages
iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED
iNSTALLER.
iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.
READ AND SAVE THESE iNSTRUCTiONS
FOR FUTURE REFERENCE.
If the information
in this manual is not followed
exactly, a
fire or explosion
may result causing property damage, personal injury
or death.
FOR YOUR SAFETY:
--
Do not store or use gasoline
or other flammable
vapors and liquids
in the vicinity
of this or any other appliance.
--
WHAT TO DO IF YOU SMELL GAS:
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any phone in your
building.
•
Immediately
call your gas supplier from a neighbor's
phone.
Follow
the gas supplier's
instructions.
•
If you cannot reach your gas supplier, call the fire department.
--
Installation
and service must be performed by a qualified
installer,
service agency or the gas supplier.
Appliances
Installed
in the state
of Massachusetts:
This Appliance can only be installed
in the state of Massachusetts by a
Massachusetts licensed plumber or
gasfitter.
This appliance must be installed with a
three (3) foot / 36 in. long flexible gas
connector.
A"T" handle type manual gas valve
must be installed in the gas supply line
to this appliance.
IMPORTANT: Cabinet and
countertop
width
should match
the cutout width.
Locate Cabinet
Doors
1" (2.5 cm) Min.
Cutout
Opening.
" Min.
(61 cm Min.)
Grounded Junction Box or Wall Outlet Should Be Located 8" to 17" (20.3 cm
to 43.2 cm) From Right Cabinet and 2" to 4" (5.1 cm to 10.2 cm) From Floor.
Do not install the unit in the cabinet
before
reading
next page.
35 7/8" (91.1cm) -
31 5/16"
28 5/16" (71.9cm)
36 5/8" (93cm)
(79.5cm)
30_+1/16" (76.2_+0.15cm)
NOTE: Wiring
diagram
for
these
appliances
are enclosed
in this
booklet.
Printed in United States
21 3/4" (55.2cm) Min.
22 1/8" (56.2cm) Max
24" (61cm) Min. with
backguard
36 5/8" (93cm) Max.
35 7/8" (91.1cm)
P/N 318201681
(0906)
Rev. A
English - pages 1-11
Espahol - p_iginas 12-22
Wiring Diagrams - pages 23-24
Advertisement
Table of Contents
Related Manuals for Kenmore 790.3690
Summary of Contents for Kenmore 790.3690
- Page 1 iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER. iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE. READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE. If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
- Page 2 NOTES: Do not pinch the power supply cord between the range and the wall. Do not seal the range to the side cabinets. 24" (6! cm) minimum clearance between the cooktop and the bottom of the cabinet when the bottom of wood or metal cabinet is protected by not less than 1/4" (0.64 cm) flame retardant millboard covered with not less than No.
- Page 3 withstand heat at least 90°F above room important Notes to the Installer Read all instructions contained in these installation temperature without shrinking, warping discoloring. Do not install the range over carpeting instructions before installing range. unless you place an insulating pad or sheet of 1/4" Remove all packing material from the oven (10,16 cm) thick plywood between the range and compartments before connecting the gas and...
-
Page 4: Seal The Openings
of water column pressure (3.5 kPa). The inlet pressure Cabinet Construction to the regulator must be at least 1 " (.25 kPa) greater To eliminate the risk of cabinet burns than the regulator manifold pressure setting. Examples: and fire, do not have cabinet storage space above the If regulator is set for natural gas 4"... -
Page 5: Electrical Requirements
Assemble the flexible connector fromthe gassupply pipe LP/Propane Gas Conversion to the pressure r egulator i nthefollowingorder: This appliance can be used with Natural gas or LP/ 1. manual shutoffvalve(notincluded) Propane gas. It is shipped from the factory for use with 2. -
Page 6: Range Installation
Where a standard 2 -prong wallreceptacle is installed, _:_[ Ir_j__ Install the anti-tip bracket at this it isthe personal responsibility andobligation of the point before placing the range at its final consumer to haveit replaced b ya properly grounded position. Follow the installation instructions on 3-prong wallreceptacle. -
Page 7: Leveling The Range
Models Equipped with Leveling Legs _J__ To reduce the risk of damaging your appliance, do not handle or manipulate it by the Level the range and set cooktop height before ceramic glass. Manipulate with care. installation in the cut-out opening. Install an oven rack in the center of the oven. -
Page 8: Decorative Rear Trim Installation
Decorative Rear Trim Installation Turn on Electrical Power Open Main Shutoff Gas Valve (if required) Disconnect the power from the range. Check Igniters Make sure the range is leveled. Operation of electric igniters should be checked after Pull range toward you. Measure the distance between the floor and the range and supply line connectors have been carefully checked for leaks, and range has been connected to... - Page 9 front of oven bottom from oven front frame, and pull the Operation of Oven Burners and Oven oven bottom out of the oven. Remove burner baffle so that Adjustments burner flame can be observed. 11.5.1 Electric Ignition Burners If the flame is yellow, increase air shutter opening size (see Operation of electric igniters should be checked after "2"...
-
Page 10: Anti-Tip Brackets Installation Instructions
1. Draw a center line (CL) on the floor where the range Anti-Tip Brackets Installation should be installed. Also draw a line on the floor at the instructions range back position if there is no wall. Models Equipped with Leveling Device 2. - Page 11 Unfold paper template and place it flat on the floor Models Equipped with Levelin with the back and side edges positioned exactly To reduce the risk of tipping of the range, where the back and sides of range will be located the range must be secured to the floor by properly when installed.
- Page 12 LA INSTALACION Y EL SERVICIO DEBEN SER EFECTUADOS POR UN INSTALADOR CALIFICADO IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA USO DEL iNSPECTOR LOCAL DE ,//7" A -':'\, "\, ELECTRiCiDAD. LEA Y GUARDE ESTAS 'NSTRUCC'ONES PARA... REFERENC'A FUTURA. Si Jainformaci6n contenida en este manual no es seguida exactamente, puede ocurrir un incendio o expJosi6n causando daEos "L._ materiaJes, Jesionpersonal o Jamuerte.
- Page 13 NOTAS: No pellizque el cordon electrico entre la estufa y la pared. _) No selle la estufa a los armados de lado. Un espacio minimo de 24" (61 cm) entre la superficie de la estufa y el fondo del armario esto cuando el fondo del armado de madera o metal est,1 protegido no menos de 1/4"...
- Page 14 menos que coloque una plancha de material aislante de por Notas importantes para el Instalador Io menos 1/4 pulgada, entre la estufa y la alfombra. Lea todas las instrucciones contenidas en este manual antes de instalar la estufa. , Asegurese de que el material que recubre las paredes alrededor...
-
Page 15: Proporcione Un Suministro De Gas Adecuado
Para la operaci6n apropriada, la m_ixima presi6n de roll Construcci6n del armario entrada al regulador no debe execeder la presi6n de una Para eliminar el riesgo de columna de agua de 14"(35,56 cm) (3.5 kPa). La presi6n quemaduras o de fuego tratando de alcanzar algo pot de entrada al regulador debe set por Io menos 1"... -
Page 16: Requisitos Electricos
Re0na el conector f lexible deltubodelsuministro d egas Aisle la estufa del sistema de tuberia del suministro al regulador de lapresiOn en laorden siguiente: de gas cerrando su wilvula de cierre manual durante 1. V_ilvula d ecierre manual(noincluido) cualquier prueba de presiOn del sistema de tuberia del 2. -
Page 17: La Mudanza Del Aparato Para Reparaciones O Limpieza
Desenchufa elcable delsuministro Para los modelos equipado con un sistema deenergia el@ctrica delenchufe depared antes de de dispositivo de nivelacion: mantener la plancha decocina. Aseg0rese que e] frente de ]as patas niveladoras y el Metodopreferido Nocorte,retireo dispositivo de nivelaciOn posterior est_n ajustados Enchufe d epared derribe,bajo ninguna... -
Page 18: Nivelacion De La Estufa
Ponga un nivel sobre la parrilla (Figura 9). Tome dos Para reducir el riesgo de daflar su lecturas con el nivel puesto diagonalmente en una artefacto, no Io manipule cerca del vidrio cer_imico. direcci6n y despu_s en la otra. Nivele la estufa, si es Manip01elo con cuidado. - Page 19 a. Empuje y gireunbott6ncontrol d elquemador superior h asta la posici0n LITE (encender). Sepodria oir elencendedor haciendo c hispas. b. Elquemador sedeber_i encender encuatro(4) segundos p araunfuncionamiento normal, d espu_s dequeel airehaya sidopurgado delatuberia de suministro d egas.Controle visualmente queel quemador sehaya encendido.
- Page 20 encendedor ytendr_i unresplandor demanera s imilar a Para ajustar un tornillo de cierre flojo (Vea el gr_ifico "3" unabombilla d eluz.Cuando e lencendedor aalcanzado de ariba), vuelva a colocar el obturador de aire, y ajuste el unatemperatura suficiente p ara encender elgas, l a tornillo de cierre.
- Page 21 Dibujar una linea central en el piso donde se instalar_i Instrucciones de instalaci6n de la la cocina. Si no hay pared posterior, dibujar otra linea fijadon anti-inclination en el piso que corresponda a la parte posterior de la cocina. Para los modelos equipado un siste- Desplegar el molde de papel y colocarlo alisado sobre...
- Page 22 Desdoble la plantilla de papel y col6quela plana en Para los modeios equipado con ias el piso con los hordes laterales y el trasero colocados niveladoras. exactamente donde la parte trasera y los lados de la Para reducir el riesgo de inclinaciOn de estufa ser_in colocados cuando sea instalada.
- Page 23 COOKTOP CIRCUIT CIRCUZTO PLANCHA COCINAR CIRCUIT TABLE CUISSON RIGHT REAR IGNITER £WITCH. INTERRUPTOR ENCENOIDO W-23 TRASERO DERECHO IGNITER MODULE BOARD INTE_UPTEU_ ALLU_EU_ CUARDO DE f_ODULODE ENCENDIDO LOP BURNER A_I_ DR_T BLOC CONNECTION ALLUt_EUR QUEMAOOR DE E_CENOIO0 BUPERIO_ _I_HT rRONT I_NITER I_R_TOR E_C_DI_O _UP_...
- Page 24 OVEN CIRCUIT//CIRCUIT FOUR W-14 ELECTRONIC OVEN CONTROL/ CONTROLE ELECTRONIQUE FOUR ES 5XX CONVECTION MOTOR RAN/ J_OTEUR VENTILATRUR OONV_CT_ON BR/W _"_:, "\ DR/W-5 c_a ..DR/W1 THERMOSTAT/5_ ATCH MOTOR/NOTEDR VERROU .... _:!_ V-19 THER_OSTAT "q( . 'f(( GY-19 TEMPERATURE PROBE/ :1-6 SONUE IRERMiQUE ii /...