LG LNB7210 Owner's Manual page 17

Stream
Profile
Select the stream [Profile1], [Profile2], [Profile3] or [Profile4]
depending on Install Preset.
Note:
It is displayed the constraints according to the current preset
settings by mouse-over at the right-top of the current Preset.
- Applicable model: LND5110 / LNV5110R / LND5110R /
LNU5110R / LNB5110
Profile Profile1
Quad SXGA @
Stream 30 fps
Triple SXGA @
D1 @ 30 fps
Stream 30 fps
SXGA @
Pivot D1 @ 30 fps CIF @ 30 fps
30 fps
High SXGA @
D1 @ 60 fps
Framerate 60 fps
- Applicable model: LNB7210 / LNV7210 / LND7210 /
LNV7210R / LND7210R / LNU7210R /
LNV7210RH / LNU7210RH
Profile Profile1
1 080P @ 1 080P @
30 fps
Quad
Stream
1 080P @
30 fps
1 080P @ 1 080P @
30 fps
Triple
Stream
1 080P @
30 fps
1 080P @
30 fps
1 080P @
Pivot
15 fps
720P @
30 fps
1 080P @
60 fps
High
Framerate
720P @
D1 @ 60 fps
60 fps
> Enable: Click to activate the stream function.
> Video codec: Select the video mode (Codec) from the drop-
down list. The viewer can choose among MJPEG, H.264 and
H.264_HIGH.
> Resolution: Select the resolution from the drop-down list.
> Maximum frame rate: Set the frame rate of the image.
Note:
Refer to the table below for the supported Framerate.
If you enter the unsupported framerate, the less Encoding
Framerate than the input is applied.
For example, when 17 fps is entered, 15 fps will be applied.
Encoding
Framerate
60
50
30
25
Operation and settings
Profile2 Profile3 Profile4
SXGA @ SXGA @
CIF @ 30 fps
30 fps 30 fps
SXGA @
N/A
30 fps
N/A
N/A N/A
Profile2 Profile3 Profile4
720P @
CIF @ 30 fps
15 fps 30 fps
720P @ 720P @
CIF @ 30 fps
30 fps 30 fps
720P @
N/A
15 fps 30 fps
720P @ 720P @
N/A
30 fps 30 fps
N/A N/A N/A
720P @
CIF @ 30 fps N/A
30 fps
720P @
CIF @ 30 fps N/A
30 fps
N/A N/A N/A
N/A N/A
Sensor Framerate
60 50 30 25
O N/A N/A N/A
O O N/A N/A
O O O N/A
O O O O
20
15
10
5
4
3
2
1
> GOP size: It means "Group of Pictures". The higher the GOP,
the better is the video quality of the camera. Set the value
of GOP from 1 up to 60 depending on Install Preset settings.
This setting is valid for H.264 video format only.
> Quality: Select the Quality.
- VBR: The bit rate may vary depending on the complexity
of the video to meet the selected quality.
- CBR: The video quality may vary in order to preserve a
constant bit rate.
> Smart Codec: You can improve the image of specific area
to configure the Region or Face Detect. If you select the
[Region] option, the [Smart Codec (Region)] window is
activated.
Note :
• When the video codec is H.264 or H.264_HIGH, the
Smart Codec can be selected.
• Two areas can overlap and the sum of the two areas
have to be less than 30 % of the total area.
• Smart Codec settings area is not maintained by the
screen change by the operation of Pan / Tilt / Zoom.
When reset the Pan / Tilt / Zoom, you need to reset the
Smart Codec settings area also.
> Stream quality: If the [Quality] option set to VBR, this
option is displayed. Select the stream quality from the drop
down box, the camera supports five types. (Highest, High,
Medium, Low and Lowest)
> Bit rate: If the [Quality] option set to CBR, this option is
displayed. If the Profile is set to [Profile1], can be set the
Bitrate value from 1 024 kbps to 10 240 kbps. In case of
[Profile2], [Profile3], [Profile4], can be set from 256 kbps to
10 240 kbps.
Note:
If the 'Bit rate' is configured too low with high resolution,
the actual frame rate will decrease because of narrow
bandwidth. So you need to set or change the 'Bit rate' to
high value.
JPEG Snapshot Quality
> Snapshot Quality: Select the quality of JPEG snapshot.
• Save: Click this button to confirm the settings.
O O O O
O O O O
O O O O
O O O O
O O O O
O O O O
O O O O
O O O O
17