Page 1
OWNER'S MANUAL High Definition Network Camera Please read this manual carefully before operating your set and retain it for future reference. MODEL LNV7210R series LNV7210 series LND7210R series LND7210 series LNU7210R series 1307 (V1.0)
Recommended PC Requirements ...........4 Accessing the LG IP device..............5 LG Smart Web Viewer Overview ............6 Configuration menu overview ..........9 Configuring the LG Network Camera Device ......9 Accessing the Configuration menu .........9 System settings ..............10 Audio & Video settings ............15 Network settings ..............24 User settings .................30...
Introduction The LG Network Camera is designed to use on an Ethernet network and must be assigned an IP address to make it accessible. This manual contains instructions on how to install and manage the LG Network Camera in your networking environment. Some knowledge of networking environments would be beneficial to the reader.
Before using the system Recommended PC Requirements • Before using the LG IP device make sure the connections are The LG IP device can be used with most standard operating systems correct and verify whether proper power supply is used. and browsers. •...
Accessing the LG IP device You can access the LG IP device by following the below steps. Install LVi510 Program It recommended to use LVi510 surely. Discover the LG IP device using the IP Utility Enter the user name and password. (Note that the...
If your computer or network is protected by a proxy or It displays Video Codec, Resolution and firewall, the proxy or firewall settings can prevent the LG FPS of the selected video stream. Smart Web Viewer program. Change the proxy or firewall settings to activate the LG Smart Web Viewer program.
Page 7
Click to effect and then check the check Displays the PTZ control window. Use box of [Edge Enhancement] option. The these buttons to control the PTZ unit. user gets more sharp reception on the This button is not displayed with normal live view window.
Page 8
Displays the current surveillance live recording will be started. screen. You can monitor the camera Note: image on the live view window of the LG If recording exceed the time(1 hour) Smart Web Viewer. or size limit (1 GB), recording is stopped automatically with warning.
Storage Configuring the LG Network Camera Log & Report Language Device Camera The features and options of the LG IP camera are configured Audio & Video Stream through the Configuration menu. Audio Only administrator-level users have permission to access the Basic Configuration menu.
System settings Time mode > Synchronize with NTP Server: Select if you want to synchronize the IP device’s date and time with those of the Version time server called NTP (Network Time Protocol). Specify the Displays the current Model Name, Software, ISP and MCU version. NTP server’s name.
Page 11
Maintenance Note: Backup and Restore can happen on IP device having the same version of firmware. This feature is not intended for multi-configurations or for firmware upgrades. Firmware > Upgrade 1. Click the [Browse] button. 2. Find and open the firmware file. 3.
Page 12
Storage Notes: • The recorded file name is made automatically as the “[Created date of the file]_[GMT Recording Time].DAT” type. • If the capacity of the SD card remains less than 200 MB, stop recording or overwrite new file after delete old one as [Overwrite] setting.
Page 13
> File Format: You can selects the Recording File Format(AVI overwritten, if the micro SD card has insufficient space. or DAT). Recording, Search and Download are available • The downloaded file can be played by using the LG File according to the setting. player. Notes: >...
Page 14
Language Language list Log & Report status Select a language for the LG Smart Web Viewer configuration menu The System log provides a summary of the status of the IP device. and information display. The unit records the data of the software activity in a file.
Audio & Video settings Install Camera Preview You can preview the camera image on the preview window. 1. Move the camera to the point you want by using the arrow buttons. 2. Adjust the zoom, focus options. 3. Set the Pan, Tilt, Zoom or Focus step options. (LNU7210R’s doesn’t support the PAN and TILT function.) Notes: •...
Page 16
Note: Streaming Sensor Video When the WDR is running, [Dynamic Range Enhancer] Pivot Framerate Master Slave is operated and [Minimum Shutter Speed] is adjusted automatically. The IRIS is initialized to Manual. 50 or 60 Disable Disable Enable Disable > EIS: The image stabilizer function minimizes the appearance Disable Enable Enable...
Page 17
camera is performed autofocus once. Also the manual- 3. When the object is too away or a movement is severe. focusing is enable too. 4. When the image contrast is low. Manual: Use , button to adjust the 5. When the strong light source is in the front and back. focus position manually.
Page 18
Note: Auto: The lens iris is set automatically. Manual: Select this option when use the lens for When the [WDR] is set to [on], [Minimum] is deactivated and adjusting IRIS manually. adjusted automatically. Note: 1/10 000 1/5 000 1/2 500 1/1 500 1/1 000 When the [Manual] is selected, IRIS is fixed on full open 1/700 1/500...
Page 19
White Balance 1. When the scene contains mostly high color temperature objects, such as a blue sky or sunset. 2. When the scene is dim. ONE PUSH: If you select the [ONE PUSH] mode, you will be able to set up the White Balance automatically. >...
Page 20
Notes: Day/Night • The value of [Day >> Night] is set automatically to be always higher than the value of [Night >> Day]. • If the difference of value between the [Day >> Night] and [Night >> Day] is not big enough, may occur the problem to convert the Day and Night.
Page 21
mode, the brightness of the IR LED will be fixed. function, the afterimage may occur. Off: When the [Day/Night] menu set to [Night] mode, IR > Color Saturation: Set the intensity of the color. LED will be turned off. > Sharpness: The degree to which the boundary of the two >...
Page 22
Stream • Privacy Mask settings area is not maintained by the screen change by the operation of Pan / Tilt / Zoom. When reset the Pan / Tilt / Zoom, you need to reset the Privacy Mask settings area also. •...
Page 23
down list. The viewer can choose among MJPEG, H.264 and [Region] option, the [Smart Codec (Region)] window is H.264_HIGH. activated. Notes : > Maximum frame rate: Set the frame rate of the image. Note: • When the video codec is H.264 or H.264_HIGH, the Smart Codec can be selected.
Audio Network settings Basic Audio In > Enable: Click the check box if you want to send the audio from the microphone input connector. Note: The Clients connected to the IP device remain unaffected with additional changes made in the setting. >...
Page 25
IP address allocated router. single address. > Web port: The default HTTP port number (80) can be changed > RTP multicast: When enabled it reduces the transmission to any port within the range 1 025 to 65 535. load on the camera by making the computer of the same segment network receive the same transmission data.
Page 26
TCP/IP IPv4 address: Enter an IP address. Subnet mask: Enter a subnet mask address. Gateway: Enter the gateway address. DNS server status > Primary DNS server: Enter the Primary domain name server that translates the hostnames into IP address. > Secondary DNS server: Enter the Secondary DNS server address that backups the Primary DNS.
Page 27
DDNS IP filtering This free service is very useful when combined with the LG DDNS The access of the IP addresses in the list are allowed or denied Server. It allows the user to connect the IP device using the URL, according to the choice made in the drop-down list of the Basic rather than an IP Address.
Page 28
Deny all: Deny all the IP address basically, but the IP • Remove: Click this button to delete the IPv6 address. addresses in the list are allowed. It needs at least one IP 1. Select the alias from the list. address to activate this function.
Page 29
802.1x > Password: Type the password for the SNMP. • Save: Click this button to confirm the settings. Specifies whether 802.1x network access is enabled. You can specify network Quality of Service (QoS) settings. 802.1x/EAPOL using EAP-TLS > Enable: Select on to enable the protocol. Current authorization status of 802.1x port is displayed on buttons QoS DSCP Configuration right.
Basic Configuration • You should set the SIP port number not to conflict with multicast port and 5353. > EAPOL Version: Select the EAPOL version. > EAP ID: Enter the ID of the client certificate using up to 16 User settings characters.
Page 31
3. To confirm the password, retype the password that you Anonymous typed in the Password box. > Enable anonymous login 4. Select the authority from the drop down list to provide Check the box to enable anonymous user login - allows the the access rights to each user and then click the [Save] user access for only viewing the live stream image.
Event settings User ID: Type the user name for the Folder shared in the FTP server. Password: Type the password for the folder shared in Event Server the FTP Server. Event Servers are used to receive the recorded video clip and/or Folder: Type the path with the folder that is shared in notification messages.
Page 33
Sensor & Relay Address: Enter the SMTP server address. Port: Enter the port number. The default port is 25. Enable SSL: Check when use the SSL (Secure Socket Layer) protocol. SSL protocol is cryptographic protocols that provide secure communication on a network.
Page 34
Motion detect your installation environment. • Motion Detection settings area is not maintained by the screen change by the operation of Pan / Tilt / Zoom. When reset the Pan / Tilt / Zoom, you need to reset the Motion Detection settings area also.
Page 35
Audio detect Smart Analytics Audio Detection > Enable: Set to [ON] or [OFF]. The Basic Configuration menu is displayed when selects [ON]. Basic Configuration > Level: Select the level of audio detection from the drop-down list. You can set the level using by jog control. If you use jog control, the [Level] option is set to [Manual] automatically.
Page 36
Triggered Event > Preview: You can preview the camera image on the preview window. When an event (VA/ Motion detect/ Sensor Event/Audio detect) Note: occurs, this unit records the live images and routes as configured. When detection occurs, the text is displayed at the right of detection configuration.
Page 37
the event runs. button of the mouse to set the channel and time you want to record. FTP server(JPEG): Sends the JPEG Image to the FTP server. Image file and suffix setting is Action available. You can select Date/Time or Sequence Set the below option.
• IP Conflicts: If the LG network device is set with a static IP address and if the DHCP option is set then there may be IP’s same as the network device and other network partner. Hence set the static IP address to 0.0.0.0 to resolve this conflict.
Page 39
After the factory settings login using the default user name and password. Video Streaming problems • If the video streaming does not start on the Web browser, install the LG Web Client ActiveX program on your computer following the instructions on the Web browser. •...
Page 40
• If we obtain lower frame rate than set we need to check from the system administrator for sufficient bandwidth available or reduce the number of applications running on the client computer. • If the client PC’s are unable to access the multicast stream, check with the system administrator for the use of a valid multicast address or check if the router is supporting multicasting.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com.
Specifications Item LNV7210 series LND7210 series Image Device 6.49 mm (1/2.8 type) CMOS (2 Mega Pixels) Lens Type 3 mm to 9 mm F1.2 Day/Night Color 0.05 lx (F1.2, Gain : High, 1/30 sec) Minimum Illumination 0.003 lx (F1.2, Gain : High, 1/30 sec)
Page 43
Event Notification Relay Out, Email, FTP Pre Event Buffering Support Integrated Client LVi510 Remote S/W LG Ipsolute VMS Suite, Mobile application (iPhone, Android, iPad) Connections Up to 20 Protection IP66, IK10 Not support Security Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X...
Page 44
Item LNV7210R series LND7210R series Image Device 6.49 mm (1/2.8 type) CMOS (2 Mega Pixels) Lens Type 3 mm to 9 mm F1.2 Day/Night Color 0.05 lx (F1.2, Gain : High, 1/30 sec) Minimum Illumination 0 lx (LED On) IR Distance 20 m Support Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control, AGC, White Balance,...
Page 45
Event Notification Relay Out, Email, FTP Pre Event Buffering Support Integrated Client LVi510 Remote S/W LG Ipsolute VMS Suite, Mobile application (iPhone, Android, iPad) Connections Up to 20 Protection IP66, IK10 Not support Security Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X...
Page 46
Item LNU7210R series Image Device 6.49 mm (1/2.8 type) CMOS (2 Mega Pixels) Lens Type 3 mm to 9 mm F1.2 Day/Night Color 0.05 lx (F1.2, Gain : High, 1/30 sec) Minimum Illumination 0 lx (LED On) IR Distance 30 m Support Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control, AGC, White Balance, Image Enhancement...
Page 47
Event Notification Relay Out, Email, FTP Pre Event Buffering Support Integrated Client LVi510 Remote S/W LG Ipsolute VMS Suite, Mobile application (iPhone, Android, iPad) Connections Up to 20 Protection IP66, IK10 Security Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X...
Need help?
Do you have a question about the LNV7210 series and is the answer not in the manual?
Questions and answers