Related Manuals for LG LCP3750T Series
Summary of Contents for LG LCP3750T Series
- Page 1 OWNER’S MANUAL Dome Camera Please read this manual carefully before operating your set and retain it for future reference. MODEL LCP3750T Series LCP3750 Series...
-
Page 2: Safety Information
Safety Information Safety Information REGULATORY INFORMATION: FCC Part 15 CAUTION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part RISK OF ELECTRIC SHOCK 15 of the FCC Rules. These limits are designed to provide DO NOT OPEN reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 3 LG Electronics hereby declares that this/ these product(s) is/are in compliance 4. The correct disposal of Your old batteries/ with the essential requirements and other...
-
Page 4: Important Safety Instructions
Safety Information IMPORTANT SAFETY 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been INSTRUCTIONS damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. - Page 5 Safety Information • Before operating, please check proper temperature, About Static Electricity Removal humidity and power source ratings. Before installing the camera, touch a metal case or other Use the camera under conditions where temperature metallic parts with your hand to remove static electricity is from -20 °C to 50 °C and humidity is below 80 %.
-
Page 6: Table Of Contents
Contents Contents Connecting LKD1000 controller Connecting RS-485 device Connecting power source Protocol and baud rate settings Camera ID Setting Removing the Protection Tape Mounting the camera Safety Information Wall mount (optional) Pendant mount (Optional) IMPORTANT SAFETY INSTRUCTIONS Safety Precautions Operation Preparation Setup Menu Overview Menu navigation... - Page 7 Contents Auto Pan setting Privacy Mask setting Special setting Auto Tracking setting (Optional) OSD Settings User title setting ZOOM MAG setting FUNCTION setting DOME ID setting LANGUAGE Setting ALARM Setting Alarm In setting Alarm Out setting RESET Setting Information Initialization Camera reset Factory reset Appendix...
-
Page 8: Preparation
Preparation Preparation Introduction • Pattern recording function A routine of manual operations can be stored and reproduced repeatedly. The Pan, Tilt and Zoom controls are available for pattern recording. The dome cameras are designed for installation in an Note outdoor video surveillance system. The available total time of pattern differs depending The camera incorporates the digital signal processor, pan/ on camera’s operation. -
Page 9: Accessories
Preparation Accessories • Alarm Out function (2 channels) When alarm inputs are supplied via the alarm input connector on the camera, the camera sends output signals via the alarm output connector on the camera. • Controls by General Controller This camera can be controlled by RS-485. Especially the camera has an excellent cost-saving effect because it can be controlled by the general RX point of contact signal. -
Page 10: Part Names And Functions
Preparation Part Names and Functions BNC connector cover cap Video output BNC connector Supplies analog video signal (composite) to the connected device. RS-485 Data Communication Alarm In Data Terminal Input data terminal for alarm (relay) signal. Alarm Out Data Terminal Output data terminal for alarm (relay) signal. -
Page 11: Installation
Installation Installation Connections Precautions • The following steps of installation and connection work should be done by qualified service personnel or system installers and should conform to all local codes. • Before you install and connect the camera, check and prepare the required peripheral devices and cables. •... -
Page 12: Connecting Display Device
Installation > Caution Connecting Display device Do not connect one alarm sensor to the several The video signal connection between the camera and the camera’s alarm input connector. monitor. Display device connection Alarm input connection Alarm device Alarm device Alarm device Alarm device Adaptor Cable Alarm In Data Terminal... - Page 13 Installation Alarm Input function ALARM IN 2 Gray This speed dome camera has a terminal that can sense the ALARM IN COM Yellow alarm signals. If the alarm sensor that has installed in a door, window, ALARM IN 3 White safe etc.
-
Page 14: Alarm Output Connections
Installation ALARM output connections Adapter cable Connect the alarm device to the alarm output data port. Description Alarm signal output at an event occurrence. You can set the Alarm Output to the normal open or normal close mode. ALARM OUT [NO1] 1. -
Page 15: Connecting Lkd1000 Controller
Installation Connecting LKD1000 controller RS-485 connection 1. Connect the Adapter cable to the RS-485 Data Communication of the camera. 2. Connect the LKD1000 controller to the Adapter cable. (Refer to the manuals of the LKD1000 controller for more details.) LKD1000 connection RS-485 device RS-485 device RS-485 Data... -
Page 16: Connecting Power Source
Pelco D Pelco P OSD Set Note If you are not using the controller with LG Multix protocol, there may be some limitation of function control. 5. Assemble the dome cover and the camera assembly cover in the reverse order. -
Page 17: Camera Id Setting
Installation Camera ID Setting OFF OFF OFF OFF OFF The camera’s ID is set to “0” as factory default. If you use OFF OFF OFF two or more cameras simultaneously, change the ID of the OFF OFF OFF cameras. OFF OFF OFF Set the camera ID setting referring to the pictures and the table on the below. - Page 18 Installation OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF...
- Page 19 Installation OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF...
-
Page 20: Removing The Protection Tape
Installation Removing the Protection Tape OFF OFF OFF OFF OFF You should remove the protection tape before installing OFF OFF OFF OFF the camera. Remove the protection tape carefully. OFF OFF OFF 1. Loosen the screws using the wrench and remove the OFF OFF OFF dome cover. -
Page 21: Mounting The Camera
Installation Mounting the camera 4. Drill a hole on the wall where you want to install the pipe. Pass the connection cable through the wall mount assembly so that they hang down. You can mount the camera on the ceiling or wall. Wall mount (optional) Install the camera by the following order. - Page 22 8. Tighten the locking screw. Note You can install the PIPE Installation Bracket direct to the other type LG Wall Mount assembly. This LG Wall Mount assembly make to easy to install your camera.
-
Page 23: Pendant Mount (Optional)
Installation Pendant mount (Optional) 4. Drill a hole on the wall where you want to install the pipe. Pass the connection cable through the pendant Install the camera by the following order. mount assembly so that they hang down. 1. Disassemble the PIPE Installation Bracket to remove the [A] part. - Page 24 Installation 5. Install the pendant mount assembly. 7. Attach the camera to the camera assembly bracket by following step a and b. Align the locking point of the wall mount assembly and the camera. 6. Connect the connection cable and the safety cable to the camera body.
- Page 25 Installation Note 9. Assemble the camera cover as shown below. You can install the PIPE Installation Bracket direct to the other type LG Wall Mount assembly. This LG Wall Mount assembly make to easy to install your camera.
-
Page 26: Operation
Operation Operation Setup Menu Overview The following table shows the list of menu items and options. You can adapt the camera to your requirements by setting up the respective items in these menus. 1st level 2nd level 3rd level Contents FOCUS MODE AUTO/MANUAL/ONE PUSH/ZOOM TRIG FOCUS DIST... - Page 27 Operation DAY/NIGHT NIGHT 3D-DNR MIDDLE HIGH CAMERA SET COLOR -50 to 50 COLOR SHARPNESS 0 to 68 STABILIZER RETURN NAME OFF/ON SPEED 1 to 127 DWELL TIME 1 to 255 IRIS AUTO, 20, 40, 60, 80, 100 % OFF/ LOW WDR/ MID. WDR HIGH WDR/ LOW BLC/ MID.
- Page 28 (1 MIN to 100 MIN) AUTO RETURN TILT LIMIT ON/OFF MOTION DET ON/OFF SENSITIVITY(0 to 100) LG MULTIX/ PELCO C/ PROTOCOL PELCO D/ PELCO P COMMUNICATION 2 400/ 4 800/ 19 200/ 38 400/ BAUDRATE 9 600 BPS SAVE & EXIT...
- Page 29 Operation ACTION STAY / RETURN LOST MODE TIME OUT 10 / 30 S / 1 / 2 / 3 / 4 / 5 MIN AUTO TRACKING RETURN (LCP3750T model PAN/TILT SET TRACK TIME INFINITE / 10 / 30 S / 1 / 2 / 3 / 4 / 5 MIN only) SENSITIVITY LOW / MIDDLE / HIGH...
-
Page 30: Menu Navigation
We use the LKD1000 controller in this manual to explain PRESET /CAM1 the features of the LG Dome camera because of the LKD1000’s ability to control all of the LG Dome camera’s advanced features. (For detailed controller instructions, refer to the LKD1000 Controller Manual.) -
Page 31: Camera Menu Settings
Operation Camera menu settings Focus Distance setting Selects the minimum shooting distance for the focus. Select [FOCUS DIST] option on the [FOCUS] menu, then select a focus distance value. Focus setting Zoom Start setting The camera adjusts the focus automatically by sensing the You can set the zoom start position of the camera. -
Page 32: White Balance Setting
Operation • AUTO: The lens iris is set automatically. SHUTTER (Shutter Speed) setting Select the desired shutter speed for camera exposure. You • MANUAL: Use [Near] or [Far] button to select the DC Iris can change the shutter speed to higher speed to capture level. -
Page 33: Day/Night Setting
Operation When the scene mostly contains high color D/N LEVEL: Use [Near] or [Far] button to select a temperature objects, such as a blue sky or level. sunset. DWELL TIME: Use [Near] or [Far] button to select When the scene is dim. a dwell time. -
Page 34: Color Setting
Operation Color setting You can switch the displayed picture to grayscale or color. 1. Select [STABILIZER] option on the [CAMERA SET] menu. 2. Use [Near] or [Far] button to ser it [ON] or [OFF]. 1. Select [COLOR] option on the [CAMERA SET] menu. 2. - Page 35 Operation To register preset positions 2. Select the memorized preset position’s index number then press [Open] or [Close] button. The camera moves 1. Select the [SET PRESET] option on the [PRESET] menu. to the preset position and the picture of the camera in 2.
-
Page 36: Group Tour Setting
Operation Group tour setting To delete a group You can delete a memorized group. You can create a group using preset positions that are registered already. A maximum of 10 groups is available. 1. Select [CLEAR] option on the [GROUP TOUR] menu. 2. -
Page 37: Auto Pan Setting
Operation To play the pattern 8. Repeat steps 1 to 7 to add additional positions. 9. Select [RETURN] option and press [Open] or [Close] 1. Select [RUN] option on the [PATTERN] menu. button to exit the setting menu. 2. Select the recording number and then press [Open] or Note [Close] button to play the programmed pattern. -
Page 38: Special Setting
Operation Special setting 1. Select [PRIVACY MASK] option on the [PAN/TILT MENU]. 2. Press [Open] or [Close] button to display the PRIVACY MASK MENU. 3. Use [Near] or [Far] button to select a zone number on the [MASK NUMBER] option. 4. - Page 39 Operation Home position Tilt limit The home position is the camera’s basic position. You can specify the tilt range. If you set this function, the camera is able to tilt from 10 º to 170 º . The camera returns to this position whenever you want. Use the following procedure to make the home position.
-
Page 40: Auto Tracking Setting (Optional)
Operation Note Auto Tracking setting (Optional) Environmental conditions Note In the case of following installation conditions, object The Auto Tracking option is supported LCP3750T series tracking errors may occur. only. • Contrast between object and background is low. • Dome cover is contaminated by raindrops or snow Configure Auto Tracking MENU options. - Page 41 Operation Note Camera Height Use [Near] or [Far] button to select how high the camera is • Under low light circumstances, tracking function installed. may not work. • Tracking error may occur by the headlight of Lost Mode vehicle. You can configure what the camera will execute when the •...
-
Page 42: Osd Settings
Operation OSD Settings • CLR: If you enter the wrong code, select [CLR] then press [Open] or [Close]. All letters will be erased at once. • POS: Move the USER TITLE position on the screen using the [Near] or [Far] buttons. •... -
Page 43: Dome Id Setting
Operation ALARM Setting DOME ID setting Displays or removes the Camera ID OSD on the screen. This camera has a terminal that can sense the alarm signals. The camera can be programmed to go to a preset with a signal from any connected alarm device. 1. -
Page 44: Alarm Out Setting
Operation Alarm Out setting Initialization 1. Select one of the alarm out options on the [ALARM You can initialize the camera settings. SET] menu. 1. Select [INITIALIZATION] option on the [RESET] menu. 2. Use [Near] or [Far] button to set it [ON]. 2. -
Page 45: Appendix
Appendix Appendix Specifications Model LCP3750-AN LCP3750-AP LCP3750T-AN LCP3750T-AP Signal System NTSC NTSC Image Sensor 4.5 mm(1/4 Type) Super HAD II CCD Total Pixels Number 520 000 Pixels 610 000 Pixels 520 000 Pixels 610 000 Pixels Effective Pixels Number 490 000 Pixels 570 000 Pixels 490 000 Pixels 570 000 Pixels... - Page 46 Group Touring Maximum 10 Groups Coax : Pelco-C (Coaxial) Protocol RS-485 : LG Multix, Pelco(D/P) Operating Temperature/Humidity -20 ˚C to 50 ˚C / 0 % RH to 80 % RH Safekeeping Temperature/Humidity -30 ˚C to 60 ˚C / 0 % RH to 90 % RH...
- Page 48 AB28...