Table of Contents
Advertisement
Quick Links
Introduction
The Full HD 1080P HDMI Wireless Extender
transmits HDMI signals wirelessly up to 50ft.
Key Features and Benefits
•
Compliant with WDHI 1.0, HDCP 2.0, and
HDMI standards
•
5GHz unlicensed band with support for
Dynamic Frequency Selection (DFS)
•
Supports video bandwidth up the 3Gb/s
•
Supports 1080p/60GHz non-compressing
video
System Requirements
•
PC or A/V devices with an available HDMI
output port
•
HDMI display
04-0711B
Full HD 1080P HDMI
Wireless Extender
Quick Installation Guide
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SIIG CE-H20S11-S1
Summary of Contents for SIIG CE-H20S11-S1
- Page 1 Full HD 1080P HDMI Wireless Extender Quick Installation Guide Introduction The Full HD 1080P HDMI Wireless Extender transmits HDMI signals wirelessly up to 50ft. Key Features and Benefits • Compliant with WDHI 1.0, HDCP 2.0, and HDMI standards • 5GHz unlicensed band with support for Dynamic Frequency Selection (DFS) •...
-
Page 2: Package Contents
Package Contents • HDMI Transmitter (Tx) • HDMI Receiver (Rx) • DC 12V Power Supply (2) • IR cable • HDMI cable (2) • Quick installation guide Layout Power LED Indicator Antenna Wireless LED Indicator On/ Off Switch Power Jack Reset Button HDMI Input Remote Extender... - Page 3 Power LED Indicator Wireless LED Indicator Antenna HDMI Output Reset Button On / Off Switch Power Jack Figure 2: Receiver (Rx) Figure 3: IR cable...
-
Page 4: Wireless Led
LED Indicators Power LED • Red: Power Off • Blue: Power On Wireless LED • Red: Wireless Dis-connected • Blue: Wireless Connected • Red and Blue Blinking: Search Signal Hardware Installation Power off all devices, including the source HDMI device and HDMI display. Connect an HDMI cable (included) from the HDMI device to the Transmitter's HDMI Input. -
Page 5: Hdmi Input
Connect an HDMI cable (included) from the Receiver's HDMI Output to the TV's HDMI Input. Plug the DC 12V Power Supply into the Transmitter's power jack, then plug it into a reliable power source. Plug the DC 12V Power Supply into the Receiver's power jack, then plug it into a reliable power source. - Page 6 Answer: Make sure you select HDMI as the input source in your TV. • Wireless LED Lighting up in Red - Make sure the proper cables are connected between the Transmitter (Tx) and your AV devices. - Make sure your source devices connected to the Transmitter (Tx) are powered on.
- Page 7 Question 3: Poor picture quality or intermittent video. Answer: Make sure the transmission distance is less than 66 feet (LOS). • Check if the video resolution of your HDMI source device matches the Transmitter (Tx) and Receiver (Rx) Specification. Question 4: No audio. Answer: Check your TV’s volume is properly set and not set in “MUTE”...
- Page 8 Blank Page...
- Page 9 Blank Page...
- Page 10 Blank Page...
-
Page 11: Technical Support And Warranty
Go to www.siig.com, click Support, then Request A Product Replacement to submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request will be processed, if the product is determined to be defective, an RMA number will be issued. - Page 12 Fremont, CA 94538-3152, USA Phone: 510-657-8688 Full HD 1080P HDMI Wireless Extender is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. All other names used in this publication are for identification only and may be trademarks of their respective owners.
Need help?
Do you have a question about the CE-H20S11-S1 and is the answer not in the manual?
Questions and answers