Appendix I - Regulatory Compliance - Multitech RF600 User Manual

Appendix I – Regulatory Compliance
EMC, Safety, and R&TTR Directive Compliance
The CE mark is affixed to this product to confirm compliance with the following European Community Directives:
Council Directive 89/336/EEC of 3 May 1989 on the approximation of the laws of Member States relating to electromagnetic compatibility.
and
Council Directive 73/23/EEC of 19 February 1973 on the harmonization of the laws of Member States relating to electrical equipment
designed for use within certain voltage limits;
and
Council Directive 1999/5/EC of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of
their conformity.
FCC Part 15 Regulation for the Modem Operation
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
FCC Part 68 Telecom for the Modem Operation
1. This equipment complies with Part 68 of the Federal Communications Commission (FCC) rules. On the outside surface of this
equipment is a label that contains, among other information, the FCC registration number. This information must be provided to the
telephone company.
2. As indicated below, the suitable jack (Universal Service Order Code connecting arrangement) for this equipment is shown. If
applicable, the facility interface codes (FIC) and service order codes (SOC) are shown.
3. An FCC-compliant telephone cord with modular plug is provided with this equipment. This equipment is designed to be connected to
the phone network or premises wiring using a compatible modular jack which is Part 68 compliant. See installation instructions for
details.
4. The ringer equivalence number (REN) is used to determine the number of devices that may be connected to the phone line. Excessive
REN's on the phone line may result in the device not ringing in response to an incoming call. In most, but not all areas, the sum of the
REN's should not exceed (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total
REN's, contact the local phone company.
5. If this equipment causes harm to the phone network, the phone company will notify you in advance that temporary discontinuance of
service may be required. But if advance notice isn't practical, the phone company will notify the customer as soon as possible. Also,
you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
6. The phone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the
equipment. If this happens, the phone company will provide advance notice in order for you to make necessary modifications in order
to maintain uninterrupted service.
7. If trouble is experienced with this equipment (the model of which is indicated below) please contact Multi-Tech Systems, Inc., at the
address shown below for details of how to have repairs made. If the equipment is causing harm to the network, the phone company
may request that you remove the equipment from the network until the problem is resolved.
8. No repairs are to be made by you. Repairs are to be made only by Multi-Tech Systems or its licensees. Unauthorized repairs void
registration and warranty.
9. This equipment should not be used on party lines or coin lines.
10. Manufacturer and device information:
Manufacturer:
Trade name:
Model Numbers:
FCC Registration Number:
Ringer Equivalence:
Modular Jack:
Service Center in U.S.A.:
Multi-Tech Systems, Inc. RouteFinderVPN RF760/660/600VPN User Guide (PN S000323D)
Multi-Tech Systems, Inc.
RouteFinderVPN 
RF600VPN, RF660VPN, and RF760VPN
AU7-USA-25814-M5-E
0.3B
RJ-11C or RJ-11W
Multi-Tech Systems Inc.
2205 Woodale Drive
Mounds View, MN 55112
(763) 785-3500 Fax (763) 785-9874
Appendix I – Regulatory Compliance
164