Table of Contents
Advertisement
G
S
AS
UPPLY AND
Accessories Wiring
If it is necessary for the installer to supply additional line voltage
wiring to the inside of the furnace, the wiring must conform to all
local codes, and have a minimum temperature rating of 105°C. All
line voltage wire splices must be made inside the furnace junction
box.
The integrated control module humidifier terminals (HUM) are en-
ergized with 115 volts whenever the induced draft blower is ener-
gized. The integrated control module electronic air cleaner termi-
nals (EAC) are energized with 115 volts whenever the circulator
blower is energized.
24 V
H
OLT
UMIDIFIER
A 5" long brown wire in the wire harness at the low fire pressure
switch provides 24 VAC humidifier control. This wire is powered
any time the pressure switch is closed. To connect 24 VAC HUM,
connect the 24 VAC line of the humidifier to the 5" brown wire. The
connection can be made by either stripping the wire and using a
wire nut or by using a field supplied quick connect terminal. The
wiring must conform to all local and national codes. Connect the
COM side of the humidifier to the C terminal on the furnace control
board (or to the COM side of the 24 VAC transformer). Do not
connect 115V humidifier to these terminals.
G
S
P
AS
UPPLY AND
IPING
The furnace rating plate includes the approved furnace gas input
rating and gas types. The furnace must be equipped to operate on
the type of gas applied. This includes any conversion kits required
for alternate fuels and/or high altitude.
T
O
PREVENT
UNRELIABLE
OPERATION
INLET
GAS
SUPPLY
PRESSURE
MUST
RATING
PLATE
WITH
ALL
OTHER
.
OPERATING
P
IPING
CAUTION
,
OR
EQUIPMENT
DAMAGE
BE
AS
SPECIFIED
ON
THE
UNIT
HOUSEHOLD
GAS
FIRED
APPLIANCES
Inlet gas supply pressures must be maintained within the ranges
specified in the following table. The supply pressure must be
constant and available with all other household gas fired appli-
ances operating. The minimum gas supply pressure must be
maintained to prevent unreliable ignition. The maximum must not
be exceeded to prevent unit overfiring.
Natural Gas
Propane Gas
H
A
IGH
LTITUDE
When this furnace is installed at high altitude, the appropriate High
Altitude orifice kit must be applied. This is required due to the
natural reduction in the density of both the gas fuel and combus-
tion air as altitude increases. The kit will provide the proper design
certified input rate within the specified altitude range.
High altitude kits are purchased according to the installation alti-
tude and usage of either natural or propane gas. Contact your
distributor for a tabular listing of appropriate altitude ranges and
corresponding manufacturer's high altitude (Natural, propane gas,
and/or Pressure Switch) kits.
Do not derate the furnace by adjusting the manifold pressure to a
lower pressure than specified on the furnace rating plate. The
combination of the lower air density and a lower manifold pressure
will prohibit the burner orifice from drawing the proper amount of air
into the burner. This may cause incomplete combustion, flash-
back, and possible yellow tipping.
In some areas the gas supplier may artificially derate the gas in an
effort to compensate for the effects of altitude. If the gas is artifi-
cially derated, the appropriate orifice size must be determined
based upon the BTU/ft
tude. Refer to the National Fuel Gas Code, NFPA 54/ANSI Z223.1,
and information provided by the gas supplier to determine the proper
orifice size.
A different pressure switch may be required at high altitude regard-
less of the BTU/ft
tor for a tabular listing of appropriate altitude ranges and corre-
sponding manufacturer's pressure switch kits.
P
G
ROPANE
AS
P
OSSIBLE
PROPERTY
OCCUR
IF
THE
CORRECT
APPROPRIATE
KITS
FURNACE
OPERATION
QUALIFIED
INSTALLER
This unit is configured for natural gas. The appropriate
THE
manufacturer's propane gas conversion kit, must be applied for
propane gas installations. Refer to the Propane Gas and/or High
Altitude Installations for details.
30
Inlet Gas Supply Pressure
Minimum: 5.0" w.c.
Maximum:10.0" w.c.
Minimum: 11.0" w.c.
Maximum:13.0" w.c.
D
ERATE
3
content of the derated gas and the alti-
3
content of the fuel used. Contact your distribu-
C
ONVERSION
WARNING
,
DAMAGE
PERSONAL
INJURY
CONVERSION
KITS
ARE
NOT
MUST
BE
APPLIED
TO
ENSURE
. A
LL
CONVERSIONS
MUST
.
OR
SERVICE
AGENCY
OR
DEATH
MAY
. T
INSTALLED
HE
SAFE
AND
PROPER
BE
PERFORMED
BY
A
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
