How To Reset The Mht100 - McIntosh MHT100 Owner's Manual

Default Settings, con't
Analog Input Trim (Zones A and B):
Name Level
AUX ................... 0.0dB ......................... 34
CD ...................... 0.0dB ......................... 34
SAT .................... 0.0dB ......................... 34
TV ...................... 0.0dB ......................... 34
DVD ................... 0.0dB ......................... 34
VCR 1 ................ 0.0dB ......................... 34
VCR 2 ................ 0.0dB ......................... 34
TUNER .............. 0.0dB ......................... 34
Digital Inputs (Zones A):
Letter Name
A ......................... AUX ............................ 34
B .......................... CD ............................... 34
C .......................... SAT .............................. 34
D ......................... TV ................................ 34
E .......................... DVD ............................ 34
F .......................... VCR 1 .......................... 34
Component Video Inputs (Zones A):
Number Name
1 .......................... SAT .............................. 34
2 .......................... DVD ............................ 34
Video Power Control:
Number Power Control
1-8 ....................... Power On ........................ 36
Trim Select (Zones A):
Adjustment
Subwoofer ................... 0dB ............................ 43
Surr Spkr ...................... 0dB ............................ 43
Center Spkr .................. 0dB ............................ 43
Treble ........................... 0dB ............................ 44
Bass ............................. 0dB ............................ 44
Display ......................... 8 ................................. 44
Surround Modes (Zones A):
Name
AUX ................... Stereo ............................ 45
CD ...................... Stereo ............................ 45
SAT .................... Stereo ............................ 45
TV ...................... Stereo ............................ 45
DVD ................... Stereo ............................ 45
VCR 1 ................ Stereo ............................ 45
VCR 2 ................ Stereo ............................ 45
TUNER .............. Stereo ............................ 45
26
Refer to Page
Refer to Page
Refer to Page
Refer to Page
Setting Refer to Page
Mode Refer to Page
Tuner Presets* (Zones A and B):
Presets Initial Settings
FM 1-9 ................. Manual Tune,
............................. 87.50MHz,
............................. no Title,
............................. not assigned ..................... 53
AM 1-9 ................ Manual Tune,
............................. 520.00KHz,
............................. no Title,
............................. not assigned ..................... 53
System Settings (for North America):
Name Settings
Video ......................... NTSC .......................... 38
Tuner ......................... USA ............................ 38
Temporary Display .... Full .............................. 38
*The Tuner Presets are applicable only if the TM1 AM/FM
Tuner Module is installed inside the MHT100.

How to Reset the MHT100

If it should become necessary to reset the MHT100 to the
Default Settings, follow the procedure below:
Notes: 1. First, if you are experiencing difficulties in operating
the MHT100, place the POWER ON/OFF in the OFF
Position for 5 minutes and then place it in the ON
Position. Turn-On the MHT100 using the STANDBY/
ON Push-button.
2. If the above step doesn't return the MHT100 to normal
operation then call your dealer for assistance or
McIntosh Technical Support.
3. Returning the MHT100 to Default Setup Settings
should be a last resort, not the first.
4. If possible, first write down any current Setup Settings
and Tuner Presets before proceeding, as all settings
will be returned factory default condition.
Press the POWER switch to ON, the Red LED above the
STANDBY/ON Push-button lights to indicate the MHT100
is in Standby mode. Press the STANDBY/ON Push-button,
then immediately press and hold in the SETUP Push-button
before the title of MHT100 appears on the Front Panel Al-
phanumeric Display. When the Front Panel Alphanumeric
Display indicates SET DEFAULTS release the the SETUP
Push-button.
Note: The Video Format will return to North American Settings.
If the MHT100 is used outside of North America and
requires different settings, refer to System Settings on
page 38.
Refer to Page
Refer to Page