Making Connection Settings - Panasonic KX-VC1300 User Manual

Note
•
To continue setting another routing, repeat
steps 8–12.
•
The input "Destination" is converted to a
network address and then used. There is no
need to register multiple destination IP
addresses that have the same network
address.
13.
Press [BACK].
•
The system settings screen is displayed.

Making Connection Settings

Note
•
You can use the administrator menu to hide the
connection settings screen (Page 135).
1.
Select "Call set up" and press [ENTER].
•
The connection settings screen is displayed.
2.
Use [ ][ ] to select the following items for input:
•
The following items are displayed over 3 pages.
To view all the items, press [R] to move to the
next page, and press [B] to move to the
previous page.
Note
•
You must save the settings separately
for each screen on which you changed
the settings.
•
When "SIP" is set to "OFF" on the call
type settings screen (Page 128),
"Encryption (SIP)" cannot be set.
•
When "H.323" is set to "OFF" on the
call type settings screen (Page 128),
"Encryption (H.323)" cannot be set.
"Answer Mode": Use [
answer video conference calls ("Manual" [default],
"Auto", or "Forced Answer") (Page 58).
"More than one incoming call": Use [
select whether to accept calls from Sub Sites to
make video conferences of more than 2 parties.
–
"ON" (default): Allow calls with more than 2
parties.
–
"OFF": Do not allow calls to have more than 2
parties.
Note
•
For sites operating as "Main Sites" in
multiple-party video conference calls using
the built-in MCU, select "ON".
Document Version 2015-12
][ ] to select how to
][ ] to
"Max. Bandwidth": Press [ENTER] and use [
[ ] to select the maximum allowed bandwidth to
be used (256 kbps–18 Mbps) (default: 9.0 Mbps).
"Max. Bandwidth Per Site (LAN 1)": Press
[ENTER], and then use [
maximum bandwidth per site ("256 kbps" -
"18 Mbps", or "Not Specified") (default: "Not
Specified").
"Max. Bandwidth Per Site (LAN 2)" (KX-VC1600
only): Press [ENTER], and then use [
select the maximum bandwidth per site
("256 kbps" - "18 Mbps", or "Not Specified")
(default: "Not Specified").
Note
•
For the KX-VC1300, "Max. Bandwidth Per
Site (LAN 1)" is displayed as "Max.
Bandwidth Per Site".
•
During a 2-party call, the bandwidth of the
site with the lowest-set maximum
bandwidth is applied, and in a multiple-party
call, bandwidth is applied according to each
site's maximum bandwidth and the number
of connected sites. However, when the
value of "Max. Bandwidth Per
Site" (excluding "Not Specified") is
smaller, the value of "Max. Bandwidth Per
Site" is applied as the maximum bandwidth.
•
You cannot select a value that is higher than
the maximum bandwidth set by the dealer.
For details, contact your dealer.
"Dual stream": Use [
stream communication is enabled.
–
"ON" (default): Enables dual stream
communication.
–
"OFF" Disables dual stream communication.
"Send Content Method": Press [ENTER], and
then use [ ][ ] to select the contents sending
method when dual stream is enabled.
–
"Auto" (default): Automatically selects either
dual stream or single stream.
–
"Single stream": Fixed to single stream.
"Encode rate": Press [ENTER] and use [
to select the encoding rate ratio for the main stream
and sub stream.
–
"Main (30%) < Sub (70%)": Prioritise the sub
stream during calls.
–
"Main (50%) = Sub (50%)" (default): Use the
same priorities during calls.
–
"Main (70%) > Sub (30%)": Prioritise the main
stream during calls.
Contacts and Settings
][ ] to select the
][ ] to
][ ] to select whether dual
][
User Manual
]
]
109