1. Manuals
  2. Brands
  3. Marquis Manuals
  4. Indoor Fireplace
  5. MQHBZDV3636
  6. Installation instructions manual

Marquis Solace MQHBZDV3636 Installation Instructions Manual

Zero clearance vented gas fireplace heater
Hide thumbs Also See for Solace MQHBZDV3636:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual
Model Numbers: MQHBZDV3636, MQHBZDV4236, MQRB4236, MQRB4236T,MQHBZDV4736
Stock #'s: MQHBZDV3636N, MQHBZDV3636LP, MQHBZDV4236N, MQRB4236N, MQHBZDV4236LP,
MQHBZDV3636NE, MQHBZDV3636LPE, MQHBZDV4236NE, MQRB4236NE, MQHBZDV4236LPE
Certified to: ANSI Z21.88-2014 • CSA 2.33-2014ZERO CLEARANCE VENTED GAS FIREPLACE HEATER
Stock #'s: MQRB4236NT, MQRB4236LPT, MQHBZDV4736N, MQHBZDV4736LP,
MQRB4236NTE, MQRB4236LPTE, MQHBZDV4736NE, MQHBZDV4736LPE,
Certified to: ANSI Z21.50-2014 • CSA 2.22-2014 ZERO CLEARANCE VENTED GAS FIREPLACE
SOLACE/SKYLINE

Installation Instructions

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
This appliance may be installed in an
aftermarket, permanently located,
manufactured home (USA only) or mobile
home, where not prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certified kit is used.
For Propane Horizontal installations the venting
must be a minimum of one foot vertical off the
flue before going horizontal.
A Division of R-Co. Inc.
2340 Logan Avenue
Winnipeg, Manitoba, Canada R2R 2V3
Ph: (204) 632-1962
Printed in Canada October 21, 2014
Part # 36MQ-MAN14

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Solace MQHBZDV3636 and is the answer not in the manual?

Questions and answers

Related Manuals for Marquis Solace MQHBZDV3636

Summary of Contents for Marquis Solace MQHBZDV3636

  • Page 1: Installation Instructions

    SOLACE/SKYLINE Installation Instructions Model Numbers: MQHBZDV3636, MQHBZDV4236, MQRB4236, MQRB4236T,MQHBZDV4736 Stock #’s: MQHBZDV3636N, MQHBZDV3636LP, MQHBZDV4236N, MQRB4236N, MQHBZDV4236LP, MQHBZDV3636NE, MQHBZDV3636LPE, MQHBZDV4236NE, MQRB4236NE, MQHBZDV4236LPE Certified to: ANSI Z21.88-2014 • CSA 2.33-2014ZERO CLEARANCE VENTED GAS FIREPLACE HEATER Stock #’s: MQRB4236NT, MQRB4236LPT, MQHBZDV4736N, MQHBZDV4736LP, MQRB4236NTE, MQRB4236LPTE, MQHBZDV4736NE, MQHBZDV4736LPE, Certified to: ANSI Z21.50-2014 •...

  • Page 2: Operating Instructions

    Pre-installation Questions and Answers About curing of the paint Your stove or fireplace has been painted with the highest quality silicone stove paint. This paint dries quickly in 15-20 minutes when first applied at the factory. However, due to the high temperature silicone components, the paint will cure when heat is applied to the appliance as it is first used.

  • Page 3: Table Of Contents

    Table of Contents Pre-installation Questions and Answers…………………………………........Operating Instructions………………………………………………………........Table of Contents……………………………………………………………........Safety Screen Installation…………………………………………………………………………… Mobile Home/Manufactured Housing Installation……………………........Warnings, Installations, and Operations…………………………………........Installation Requirements for the Commonwealth of Massachusetts…........MQHBZDV3636 Locating your Appliance................Fireplace Dimensions................. Framing for your Gas Fireplace..............Framing and Facing Requirements.............

  • Page 4: Safety Screen Installation

    Safety Screen Installation Z Series Contents of Kit: [1] Safety Screen [2] Side Angles [2] Horizontal Angles [12-16] DT Screws (Depending on screen size) Assembly: Attach components with supplied screws as shown. NOTE: Screens are symmetrical from top to bottom. ⚠...

  • Page 5: Mobile Home/Manufactured Housing Installation

    Mobile Home/Manufactured Housing Installation This Direct Vent System Appliance must be installed in accordance with the manufacturer’s installation instructions and the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280, or the current Standard for Fire Safety Criteria for Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240 MH Mobile Home Standard in Canada.

  • Page 6: Warnings, Installations And Operations

    Warnings, Installations and Operations Installation Regulations This gas appliance must be installed by a qualified installer in accordance with local building codes, or in the absence of local codes, with the current CAN/CSA-B149.1 or .2 Installation Code (in Canada) or the current National Fuel Gas Code Z223.1- NFPA 54 when installed in the United States. This appliance, when installed, must be electrically connected and grounded in accordance with local codes, or in the absence of local codes, with the current CSA C22.1 Canadian Electrical Code or with the National Electrical Code;...

  • Page 7: Installation Requirements For The Commonwealth Of Massachusetts

     Gas fired appliances may be used only for supplemental heat and/or decorative purposes and under no circumstances shall they provide a primary heat source.  This appliance must not be connected to a chimney flue serving a separate solid-fuel burning appliance. NOTE: It is recommended that a Carbon Monoxide (CO) Detector be installed in or near bedrooms and on all levels of your home.

  • Page 8: Locating Your Appliance

    Locating Your Appliance LOCATION KEY: Flat on Wall Across the Corner As an Island As a Room Divider Flat on Wall Corner Exterior Wall See Mantel Leg Clearances Instruction for the proper placement of fireplace. Island installation with a top vent is possible as long as the horizontal portion of the vent system does not exceed 20 feet (6.1 m).

  • Page 9: Framing For Your Gas Fireplace

    MQHBZDV3636 - Framing for your Gas Fireplace 4. When installing horizontal with a 90 degree bend maintain a mini- Framing Specifications mum of two and a half (2.5”) inches above the bend in enclo- 1. Cold climate installation recommendation: When installing this fire- sures.

  • Page 10: Framing And Facing Requirements

    HBZDV36 - Framing and Facing Requirements HBZDV36 WITH HB36CVCK (CLEAN VIEW CIRCULATING KIT) Non Combustible Header Attached Non Combustible Header Attached HB36CVCK WITH MQHB36SW SURROUND Non Combustible Header Non Combustible Header Attached...
  • Page 11 HB36 - How to Install Clean View Kit (Cvck) For HB36/HB42/HB47 CAUTION: When using CVCK DO NOT INSTALL a Louver assembly. Install optional fan kit (see Fan Instruction). Fold two standoffs up into position and mount with supplied screws. (FIG 1) Hang CVCK on top of fireplace retainer tabs and rotate down into position.
  • Page 12 MQHBZDV3636 Parts List Fireplace Part Numbers HB36CSS Safety Screen Replacement MQHBZDV3636N (Millivolt) Fireplace Heater Rated NG, Ceramic HB36PSK Pull Screen Kit for CVCK MQHBZDV3636NE (IPI) Glass, 30,500 BTU AT 75% efficient. Approved for bedroom and mobile Overlays home. HB36ADTH Arch Door Frame - Top Half Black MQHBZDV3636LP (Millivolt) Fireplace Heater Rated LP, Ceramic HB36ADDX Arch Door Frame - Deluxe Black...
  • Page 13 MQHBZDV3636 Parts List Kingsman Fireplace Venting Catalog Electronic Ignition Replacement Parts IPI Number Description 1002-P001si Valve IPI (NG; ON/OFF) ZDVHSK Horizontal Vent Starter Kit - 3 FT Length 1002-P002si Valve IPI (LP; ON/OFF) Horizontal Vent Termination, Wall Thimble, 1006-P002si Valve IPI (NG; Hi/Lo) 36”...

  • Page 14: Fireplace Dimensions

    Locating Your Appliance LOCATION KEY: Flat on Wall Across the Corner As an Island As a Room Divider Flat on Wall Corner Exterior Wall See Mantel Leg Clearances Instruction for the proper placement of fireplace. Island installation with a top vent is possible as long as the horizontal portion of the vent system does not exceed 20 feet (6.1 m).
  • Page 15 MQHBZDV4236/MQRB4236 - Framing for your Gas Fireplace 4. When installing horizontal with a 90 degree bend maintain a minimum Framing Specifications 1. Cold climate installation recommendation: When installing this fire- of two and a half (2.5”) inches above the bend in enclosures. place against non insulated exterior wall or chase, it is recom mended 5.

  • Page 16: Framing And Facing Requirements

    HB42 - Framing and Facing Requirements HBZDV42 WITH HB42CVCK (CLEAN VIEW CIRCULATING KIT) Non Combustible Header Attached Non Combustible Header Attached HB42CVCK WITH MQHB42SW SURROUND *Note: A HBCVCK must be used when installing a MQHBSW Wall Surround.

  • Page 17: Clearance To Combustibles

    HB42 - HOW TO INSTALL CLEAN VIEW KIT (CVCK) CAUTION: When using CVCK DO NOT INSTALL a Louver assembly. Install optional fan kit (see Fan Instruction). Fold two standoffs up into position and mount with supplied screws. (FIG 1) Hang CVCK on top of fireplace retainer tabs and rotate down into position. (FIG 2) Using the screws provided, fasten the non-combustible header onto the top of the CVCK assembly.

  • Page 18: Parts List

    MQHBZDV4236/MQRB4236 Parts List HB42SLCR Surround Slim Line - Chrome Fireplace Part Numbers (Coverage 37 3/8” H x 43 3/8” W) MQHBZDV4236N (Millivolt) Fireplace Heater Rated NB, HB42SLPB Surround Slim Line - Polish Brass Ceramic (Coverage 37 3/8” H x 43 3/8” W) MQHBZDV4236NE(IPI) Glass 30,500 BTU at 75% efficient.
  • Page 19 1000-306 Thermalcord - Adhesive Back for Door Frame 42HB-310 Ceramic Glass 4236RB-SRKP* Upgrade Kit 36HB-123 Upper Door Spring *NOTE: THE MQRB4236N CANNOT BE CONVERTED TO LP. OFP42SA Spark Assist If the MQRB4236NT you wish to convert to LP has a serial number less than #4708 Kingsman Fireplace Venting You MUST order the 4236RB-SRKP upgrade kit.

  • Page 20: Locating Your Appliance

    Locating Your Appliance LOCATION KEY: Flat on Wall Across the Corner As an Island As a Room Divider Flat on Wall Corner Exterior Wall See Mantel Leg Clearances Instruction for the proper placement of fireplace. Island installation with a top vent is possible as long as the horizontal portion of the vent system does not exceed 20 feet (6.1 m).

  • Page 21: Framing For Your Gas Fireplace

    MQHBZDV4736 - Framing for your Gas Fireplace sleeve is required. If greater than six and a half (6.5”) an insulation sleeve Framing Specifications is not required. 1. Cold climate installation recommendation: When installing this fire- place against non insulated exterior wall or chase, it is recom mended 5.
  • Page 22 Non Combustible Header Attached Non Combustible Header Attached Non Combustible Header Attached Non Combustible Header Attached...

  • Page 23: Clearance To Combustibles

    HB47 - HOW TO INSTALL CLEAN VIEW KIT (CVCK) CAUTION: When using CVCK DO NOT INSTALL a Louver assembly. Install optional fan kit (see Fan Instruction). Fold two standoffs up into position and mount with supplied screws. (FIG 1) Hang CVCK on top of fireplace retainer tabs and rotate down into position. (FIG 2) Using the screws provided, fasten the non-combustible header onto the top of the CVCK assembly.
  • Page 24 MQHBZDV4736 - Parts List Overlays Fireplace Part Numbers MQHBZDV4736N (Millivolt) Fireplace Decorative Rated NG, HB47ADTH Arch Door Top Half Black HB47ADDX Arch MQHBZDV4736NE (IPI) Tempered Glass, 40,000 BTU Door Frame - Deluxe Black HB47ADDA Arch Door MQHBZDV4736LP (Millivolt) Fireplace Decorative Rated LP, Frame - Double Arch Black HB47ADDD Arch Door MQHBZDV4736LPE (IPI)
  • Page 25 Kingsman Fireplace Venting Electronic Ignition Replacement Parts IPI 1002-P001si Valve IPI (NG; ON/OFF) 1002-P002si Valve IPI (LP; ON/OFF) Catalog Number Description 1006-P002si Valve IPI (NG; Hi/Lo) ZDVHSK Horizontal Vent Starter Kit - 3 FT Length 1006-P603si Valve IPI (LP; Hi/Lo) Horizontal Vent Termination, Wall Thimble, 36”...
  • Page 26 Clearances – HB36 / HB42 / HB47 – Mantels & Surrounds Warning: Combustible objects must not be placed on a non-combustible mantel unless the non- combustible mantel meets the minimum height and width requirements for a combustible mantel. Note For the installation of the MQHBSW.

  • Page 27: Mantel Leg Clearances

    Mantel Leg Clearances Mantels Depending on the depth of the fireplace mantel, it may be installed higher or lower from the top of the fireplace opening. See drawings for proper installation height of your combustible mantel. Non-combustible mantels may be installed at any height above the fireplace opening except when using MQHBSW.

  • Page 28: Mqsw Wall Mount Surround Dimensions

    MQSW Wall Mount Surround Dimensions Concave Convex HB36 HB36 HB42 HB42 HB47 HB47 Installation of MQ Wall Mount Surrounds Warning: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. Remove the old CAP (Control Access Panel), and the Lower CVCK panel by unscrewing the...

  • Page 29: Parts List

    Fan Installation for HBZDV 36/42/47 3. Wire Junction Box to 120v and wall mounted variable speed control. Fan Installation instructions for HBZDV36/42/47 Install a duplex outlet to junction box and plug fan into outlet. with or without CVCK (Clean View Circulating Kit) 4.
  • Page 30 Split Receptacle- Fan Speed Control Outside of Fireplace If you plan to locate the variable speed control switch for the fan outside of the fireplace and you require a constant source of AC power inside the unit for another accessory such as lights or an IPI valve system, follow one of the procedures below.

  • Page 31: Installing Mqrb4236 Liner Panels

    Installing MQRB4236 Liner Panels There are several types of Liner Panels available for the MQRB4236: -Flat Black Back Panel and False Bottom- (Supplied with Unit). -Porcelain Back and Side Panels- MQRB42PL Removal of False Bottom and Back Panel Remove four [4] screws from False Bottom and lift out of the Firebox (Ref.1). The Back Panel is held in place by the False Bottom and 2 Locking Tabs on the inside top of the Firebox (See Ref.2 Below).
  • Page 32 Brick Installation - For Models MQHBZDV3636/MQHBZDV4236/MQHBZDV4736 INSTALLING BRICK PANELS FOR MODEL MQHBZDV3636/MQHBZDV4236/MQHBZDV4736 1. Remove door glass from the unit by unlatching the 2 latches on top of unit. 2. (MQHBZDV4736 ONLY) Using a 1/4” nut driver remove two screws from Brick Panel Filler (#1) and discard brick panel filler. (Ref.1) 3.

  • Page 33: Installation Of Hb Porcelain Liners - Hb36Pl/Hb42Pl/Hb47Pl

    Installation of HB Porcelain Liners - HB36PL/HB42PL/HB47PL 1. Remove Door from the fireplace by unlatching the 2 latches on top of unit. 2. Remove back Log Holder by removing 3 screws from face of Log Holder. The Log Holder will have to be re- installed after the placement of the Back Panel.

  • Page 34: Gas Line Installation

    Gas Line Installation This gas appliance should be installed by a qualified installer in accordance with local building codes and with current CAN/CGA - B149.1 or .2 installation codes for Gas Burning appliances and equipment in Canada and the National Fuel Gas Code ANSI Z223 in the U.S.A.

  • Page 35: Millivolt System, Lighting, And Burner Control

    Millivolt System, Lighting, and Burner Control FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. BEFORE LIGHTING  This appliance has a pilot which must be lighted by hand. When Immediately call your gas supplier from a neighbour’s phone.

  • Page 36: Trouble Shooting The Gas Control System

    Trouble Shooting The Gas Control System BEFORE DOING ANY GAS CONTROL SERVICE WORK, REMOVE THE GLASS FRONT. WARNING: NOTE: Before troubleshooting the gas control system, be sure external gas shut off is in the “On” position. Problem Possible Causes Corrective Action Spark igniter will not light.

  • Page 37: Burner System Removal For Mqhb36/42/47

    Burner System Removal for MQHB36/42/47 Warning: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. Removing Burner System / Access Cover for MQHBZDV36/42/47 If fireplace has been installed with optional CVCK (Clean View Circulating Kit) to service fan system or burner system controls, the access cover and burner system pan will have to be removed.

  • Page 38: Burner System Maintenance

    Burner System Maintenance It is recommended to annually inspect and clean the Burner System to prevent malfunction and / or sooting. This operation should be performed by your dealer or a qualified technician. -CAUTION- Before servicing the burner system ensure that the gas supply is turned OFF and disconnect all electrical connections to the appliance.

  • Page 39: Conversion Kit Instructions - Part A

    Conversion Kit Instructions – PART A Burner Orifice Kit Number Description Pilot Orifice Brass Nipple Air Shutter Hi/Lo Regulator Brass (1000-255) 3632HB -CKLP 1001-P167SI 1001-P202SI Conversion 1000-253closed 5/16” #30 (977.167) (0.907.202) MQHBZDV3636LP -Millivolt- 3632HB –CKLPI 1001-P168SI 1002-P014SI Conversion 1000-253closed 5/16” #35 (977.168) (0.907.014) MQHBZDV3636LPE...
  • Page 40 MQHB3636/4236/4736 Gas Conversion –Part A WARNING: This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instruction s and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly a fire, explosion or production of carbon monoxide may result causing property damage, personal injury or loss of life.

  • Page 41: Gas Conversion For Top Convertible Pilot (Series 019065X) - Part B

    Gas Conversion for Top Convertible Pilot (Series 019065X) – PART B Instructions for converting SIT 190 series pilot burner injection from NG to LPG and from NG to LPG only. This information should be considered as supplemental to the Appliance Manufacturer’s Instructions. WARNING: The installation of this conversion kit must only be undertaken by a qualified and certified gas appliance installer.

  • Page 42: Gas Conversion For Modulator - Part C

    Gas Conversion for Modulator – PART C WARNING!- WARNING!-...

  • Page 43: Ipi Electronic Ignition System

    IPI Electronic Ignition System Overview The IPI system is an advanced burner controller that provides you with the option of having either a Standing-Pilot, or an intermittent igniting system. This alternating mode is controlled by the CPI/IPI Switch (Continuous Pilot Ignition/Intermittent Pilot Ignition) located on the IPI System Box.
  • Page 44 the slide switch to the middle [REMOTE] position and then push the small pushbutton to begin programming. Bring the transmitter close to the receiver and then press the power button [R] on the transmitter. An audible beep will sound to indicate the system is programmed and ready to be used. NOTE: The Remote Receiver module can also be located outside of the appliance to a maximum of 6ft away installed in a certified deep wall switch electrical box (2-3/4”...
  • Page 45 Configuration #1: Basic manual HI/LO and manual ON/OFF capabilities.
  • Page 46 Configuration #2: Remote ON/OFF and manual HI/LO capabilities. OPTIONAL: For units with remote HI/LO capabilities, a modulating servo is required to be installed on the valve. The connectors to this servo must be connected to the Remote Harness as shown in the figure above.
  • Page 47 Configuration #3: Remote ON/OFF, variable HI/LO, and fan capabilities. Refer to the fan installation/removal section for fan installation.

  • Page 48: Ipi Lighting Instructions

    IPI Lighting Instructions WARNING 1. If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. 2. Always light the pilot whether for the first time or if the gas supply has ran out with the glass door opened or removed.

  • Page 49: Door And Glass Information

    Door and Glass Information Removal of the Glass Door Glass Cleaning 1. Remove the door by unlatching the 2 top latches. Simply It will be necessary to clean the glass periodically. During start- place 2 fingers in the grooves, pull towards you and lift up, condensation, which is normal, forms on the inside of the upwards slightly.

  • Page 50: Log Placement - Logf36

    LOG PLACEMENT - LOGF36 WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. PARTS LIST STEP 1: Place log #1 onto rear log holder and center.

  • Page 51: Mqrock1/Mqrsp2 Setup For Models Mqhbzdv3636/Mqhbzdv4236

    MQROCK1/MQRSP2 Setup for Models MQHBZDV3636/MQHBZDV4236 WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. PARTS LIST STEP 1: Remove the log holder mount, log supports, and STEP 2: Attach the back rock support with the 4 screws the grate bar.
  • Page 52 MQROCK1/MQRSP2 Setup for Models MQHBZDV3636/MQHBZDV4236 STEP 5: Place rocks #1 onto the burner as shown. STEP 6: Place rocks #3 onto the burner as shown. STEP 7: Place rocks #4 onto the burner as shown. STEP 8: Place rocks #6 onto the burner as shown. STEP 9: Place remaining rocks #4 and #6 into position as Finished Rock F2 Setup shown.

  • Page 53: Mqrock1/Mqrsp1 Setup For Models Mqhbzdv4736

    MQROCK1/MQRSP1 Setup for Models MQHBZDV4736 WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. PARTS LIST: Rock #1 - 5 pieces; Rock #3 - 6 pieces;...

  • Page 54: Mqrock1/Mqrsp1 Setup For Models Mqhbzdv4736

    MQROCK1/MQRSP1 Setup for Models MQHBZDV4736 STEP 6: Place rocks #4 into position as shown. STEP 5: Place rocks #3 into position as shown. Do not place rocks directly onto the burner tubes. STEP 7: Place rocks #6 into position as shown. STEP 8: Place remaining rocks #4 and #6 into position as shown.

  • Page 55: Accessories Available For Skyline & Zdvrb3622 Ribbon Burner Units

    Accessories Available for Skyline & ZDVRB3622 Ribbon Burner Units ACCESSORY ITEM MQRB3328 MQRB3632 MQRB4236 ZDVRB3622 Silica Sand 5LB Bag c/w Unit 5LB Bag c/w Unit Not Available Not Available Yes / 5LB MAX Yes / 5LB MAX 5LB Bag c/w Unit MQ Dealer Only White Glass MQG5W Bronze Glass MQG5C...

  • Page 56: Ulk2 Universal Light Kit (Optional Accent Lighting Kit)

     MQROCK2, MQROCK3, MQRBD1 - Place rocks randomly onto False Bottom. Be careful not to cover any part of the Burner Tube as sooting may occur. MQRock2 MQRock3 MQRBD1 NOTE  Pilot Area Must Not Be Covered, as delayed ignition can occur. ...
  • Page 57 ULK2 Universal Light Kit ( Optional Accent Lighting Kit) For the Skyline Series (MQRB3328, MQRB3632, MQRB4236) and Kingsman ZDVRB3622 Please follow the current ANSI/NFPA 70 National Electrical Code in the USA and CAN/CSA C22.1 Canadian National Electrical Code in Canada. Contents of Kit: ...
  • Page 58 MQRB3328, ZDVRB3622, & MQRB4236 Screw Screw MQRB3632 Screw Screw STEP 3: Place Lamps in position in firebox. Attach to fireplace with a single screw at the locations shown above for each unit. Lamps can be placed facing upward or sideways. Replace burner tube and false bottom, along with pilot shield.

  • Page 59: Vent Termination

    Vent Termination WARNING: WHEN THE HORIZONTAL VENT TERMINATION IS ACCESSIBLE A CERTIFIED GUARD (SAFETY CAGE) SHALL BE INSTALLED. NOTE: Clearances are to the edge of terminal plate, add 6- 3/4” to clearances to arrive at center line. A - Clearance above grade, veranda, porch, deck, or balcony 12 NOTE: Local Codes or Regulations may require different inches (30cm) minimum.

  • Page 60: General Vent Installation Information

    General Vent Installation Information This gas appliance is approved to be vented either through the side wall or vertically through the roof. Only Kingsman Flex(Z- Flex)Venting Kits and components specifically approved and LABELED for this stove may be used. This appliance is also approved for use with Simpson-Duravent Direct Vent system, Ameri-Vent Direct Vent Pipe System, ICC Excel Direct, Metal Fab Sure- Seal DV and Selkirk Direct Temp.

  • Page 61: Venting Table

    How To Use The Horizontal Vent Table Venting Routes And Components Since it is very important that the vent system maintain its bal- 1. Determine the height of the system and the number of bends ance between the combustion air intake and the flue gas required.

  • Page 62: Installation Of Side Wall Venting

    Installation Of Side Wall Venting 1. Establish the minimum distance from the bottom of fireplace to centre MQHBZDV3636 of vent. Cut a hole through the wall allowing for a 11” x 11” (inside diameter) in combustible walls for wall thimble or an 8” diameter hole in a non-combustible wall (See Figure 1-2-3).

  • Page 63: Vertical Venting

    Venting Straight Up Through Roof Roof Flashing Ensure that you have the proper roof flashing by checking your 1. An Attic Insulation Shield must be installed where the vent passes roof pitch using a level and two rulers, or by using a roof pitch card. from a lower living space into an attic space where the chimney is See figure below.

  • Page 64: Glass Safety / Termination Cap Safety- All Units

    -Glass Safety- All Units IT IS THE RESPONSIBILITY OF THE HOME OWNER TO ENSURE THAT NO ONE TOUCHES A HOT APPLIANCE. If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this appliance. Any safety screen, guard, or barrier removed for servicing the appliance, must be replaced prior to operating the appliance.

  • Page 65: Approved For Power Vent Pvh58

    Approved for Power Vent PVH58 The PVH58 Horizontal Power Vent is approved for the following models only: MDV31, MDV39, MQRB3632, ZDV3622, MQZDV3622, ZDVRB3622, HBZDV3624, HBZDV3628, HBZDV3632, MQHBZDV3636, HBZDV4224, HBZDV4228, HBZDV4232, MQHBZDV4236, HBZDV4740, MQHBZDV4736, MQRB4436, MQRB5143, MQRB6961, ZRB46, ZCV39, ZCV42, MCVP42, MCVST42 The PVH58 Horizontal Power Vent Termination is intended for use where standard venting configurations are not possible.

  • Page 66: Pvh58 Power Vent Parts List

    PVH58 POWER VENT PARTS LIST NUMBER DESCRIPTION PVH58 Horizontal Power Vent Termination PVC58MV Power Vent Control Module – Millivolt Box PVC58IPI Power Vent Control Module – IPI Box PVH20H Main Wiring Harness Assembly – Extension Harness (20ft) 4/7 VENTING AND VENTING ADAPTERS For fireplaces to be converted to hard pipe (Duravent-DirectVent Pro, etc.) at the fireplace: ZDVDKA Duravent Fireplace Adapter (ZRB46 Only)

  • Page 67: Limited Lifetime Warranty

    This Limited Lifetime Warranty applies only while the unit remains at the site of the original installation and only if the unit is installed inside the continental United States, Alaska, Hawaii, and Canada. The warranty applies only if the unit is installed and operated in accordance with the printed instructions and in compliance with applicable installation and building codes and good trade practices.

This manual is also suitable for:

Solace mqhbzdv4236Skyline mqrb4236Solace mqhbzdv4736Skyline mqrb4236tSolaceSkyline

Table of Contents