Subscribe to Our Youtube Channel
Related Manuals for Winco PSS60B
Summary of Contents for Winco PSS60B
- Page 1 PACKAGE STANDBY SYSTEMS PSS60/B INSTALLATION AND OPERATIONS MANUAL PSS90/B DSE7110 PSS90-3/B...
-
Page 2: Table Of Contents
ENGINE CONTROL PANEL LAYOUT To Check” near the end of this manual. The warranty listed DSE 7110 CONTROLLER in this manual describes what you can expect from WINCO INITIAL START-UP should you need service assistance in the future. START-UP PROCEDURE... -
Page 3: Guide To Product Safety
FIRE HAZARD - NG and LP present a hazard of possible IMPORTANT SAFETY explosion and/or fire. INSTRUCTIONS Do not smoke or use open flame near the generator set. Keep a fire extinguisher nearby and know its proper use. SAVE THESE INSTRUCTION Fire extinguishers rated ABC by NFPA are appropriate. -
Page 4: Basic Information
120/240 ¨ Five-key Menu Navigation PSS90-18 277/480 ¨ Engine Exercise Mode Additional optional A.T.S. sizes are available to meet specific needs. Contact your local WINCO dealer or the WINCO Sales Department for a quote. 1270-10 REV B Page 2 60706-213... -
Page 5: Specification Table
FUNCTIONS ENGINE SPECIFICATIONS: DSE 7110 Series Control Modules perform the following protec- tion and metering functions: Refer to engine operating and maintenance instructions Generator Protection and Metering ** NOTICE ** Generator protection includes over voltage, under voltage, under Regarding Engines - This manual covers the generator portion of frequency, over frequency and overload protection. -
Page 6: Installation
These units should be mounted to allow for ample working room UNPACKING: around it. Units must be installed in accordance with all local, state and national codes. Consult your local agency having Carefully remove the carton. After inspecting the engine-generator for external physical jurisdiction for specific requirements. -
Page 7: Fuel Pressure Tables
Two (2) Regulator System (L.P. Vapor only) *************** **** WARNING **** *************** UNIT OFF TANK PSI 10-15 lbs 7-11 in 7-11 in PERSONAL DANGER - Do not use galvanized pipe in fuel line 4-6 oz 4-6oz runs. The galvanized coating can become eroded and flake off, STARTING TANK PSI 10-15 lbs... -
Page 8: Battery Installation
INSTALLING THE BATTERY ately with water and seek immediate medical attention. Spilled electrolyte is to be washed down with an acid neutral **** CAUTION **** izing agent. A common practice is to use a solution of one pound of bicarbonate of soda (baking soda) to one gallon of In the following battery installation procedure, check to be sure water. -
Page 9: Ac Electrical Connections
duplex receptacle is mounted on the generator along side circuit breaker panel, the battery tender is shipped already plugged into the receptacle. The engine blockheater installed on this unit\ should also be plugged in this receptacle. The block heater is thermostatically controlled and when plugged in will maintain the engine coolant temperature between 100 and 120 degrees F. -
Page 10: Dc Electrical Connections
C - Ground Lug, These ground lugs are bonded to ground and are provided for you to connect your ground wire from the transfer switch to. The lugs on the 80 kW will handle wire sizes #1 AWG to 300 MCM and should be torqued to 250 in. lbs. The lugs on the 60 kW will accommodate #1 AWG to 250 MCM and should be torqued to 250 in. -
Page 11: Engine Control Panel Layout
DC Interconnections to the Automatic Transfer Switch ASCO 300 UL SWITCH Your DC connection points in the ASCO 300 ATS are terminals Two control wires are required between the A.T.S. panel and the “14” and “15”. Depending on the size of the switch they are generator control terminal box. -
Page 12: Dse 7110 Controller
D. AC INTERFACE CONNECTOR - This connector is used to received while this switch is activated, the unit will not start. interface with the AC generator end. It provides the controller with the voltage, amperage and frequency reading for the display. C. -
Page 13: Initial Start-Up
motor is disengaged and goes into a rest mode after which a INITIAL START UP second attempt is made to start the engine. Should this se- quence continue through 3 cranking cycles the start sequence **************** will be stopped and the display will show ‘FAILED TO START’. ***** WARNING ***** 3. -
Page 14: Exerciser Clock
To test the automatic start Transfer Switches follow the instruction ENGINE STARTS AND THEN STOPS AND ALARM in the operator’s manual you received with your transfer switch. If LIGHT COMES ON you get a fault light during the initial start up or prior to start up it is most likely a false warning light. -
Page 15: Changing The Fuel Type
CHANGING THE FUEL TYPE **** CAUTION **** EQUIPMENT DAMAGE - Do not make any fuel adjustments or governor adjustments until all pressure readings are in compli- ance with specification. See fuel pressure charts (tables 1, 2, and 3). These engine/generator sets are very easy to convert between LP or NG. -
Page 16: 277/480 Volt
1270-10 REV B Page 14 60706-213... -
Page 17: 120/240 Volt
1270-10 REV B 60706-213 Page 15... -
Page 18: Dc Schematic - Wiring Diagram
1270-10 REV B Page 16 60706-213... -
Page 19: Outline Drawing
PSS60 OUTLINE DRAWING AND WIRING ENTRANCE PSS90 OUTLINE DRAWING AND WIRING ENTRANCE 1270-10 REV B 60706-213 Page 17... -
Page 20: Dse7110 Control Icons
MODE ICONS AUTO RUN ICONS INSTRUMENTATION ICONS Page 18 60706-213 1270-10 REV B... -
Page 21: Warning Alarm Icons
WARNING ALARMS 1270-10 REV B 60706-213 Page 19... -
Page 22: Shutdown Alarm Icons
SHUTDOWN ALARMS Page 20 60706-213 1270-10 REV B... -
Page 23: Accesing Front Panel Configuration
ACCESSING THE FRONT PANEL CONFIGURATION EDITING A PARAMETER 1270-10 REV B 60706-213 Page 21... -
Page 24: Month Warranty
WINCO’s sole liability, and Purchaser’s sole remedy for a failure under this warranty, shall be limited to the repair of the product. At WINCO’s option, material found to be defective in material or workmanship under normal use and service will be repaired or replaced. For warranty service,...
Need help?
Do you have a question about the PSS60B and is the answer not in the manual?
Questions and answers