Q.cg Tilt Power Accessory; Power Recline; Power Legrest Accessory; U.transit Option And Use - Quickie QM-710 Owner's Manual

Q M- 7 10/7 15 HD/ 72 0
5. Remain Clear During Power Accessory Operation
Please stay clear of any powered actuator while the compo-
nent is in motion. Sunrise power mechanisms move over
large ranges of travel. Users should be aware of their sur-
roundings while components are in motion.
6. Maximum User Weight
Do not exceed the weight capacity for your specific
chair/seating system configuration. Doing so could result in
premature failure or injury.
7. Latch Mode
While operating any power seating function in latched mode
use caution. In latch mode, powered seating will not stop until
a reverse command is performed or the end of travel is met.
Q. CG TILT POWER ACCESSORY
The powered CG Tilt accessory for this chair has a maximum user
weight capacity of up to 300 lbs (400 lbs for the QM-715HD).
Never exceed this capacity while operating the powered actuator.
R. POWER RECLINE
Pinch Point
Avoid putting hands or fingers near the power recline mechanism
while in operation.
Weight Capacity
The maximum user weight capacity for the power recline is up to
350 lbs. Exceeding this weight capacity could lead to injury and/or
permanent damage to the equipment.
S. POWER LEGREST ACCESSORY
The power legrest accessory has a maximum user weight capaci-
ty of up to 300 lbs (400 lbs for the QM-715HD) depending on
your chair configuration. Never exceed this capacity while oper-
ating the powered actuator.
T. LIFT & LIFT/TILT COMBO
The powered lift and/or lift/tilt modular accessory for this chair
has a maximum user weight capacity of up to 300 lbs. Never
exceed this capacity while operating the powered actuator.
WARNING
WARNING
WARNING
VII. WARNINGS: COMPONENTS & OPTIONS
U. TRANSIT OPTION AND USE
Refer also to the "Motor Vehicle Safety" section for additional tran-
sit option and motor vehicle warnings.
Transit use does not apply to the QM-715HD.
1. If possible and feasible, the rider should transfer to the
(OEM) original Equipment Manufacturer vehicle seat and use
the vehicle restraint.
2. If the wheelchair is used for transport, it must be used in a
forward-facing seating position.
3. The rider must not weigh more than 300 lbs.
4. Use only with Wheelchair Tie-down and Occupant Restraint
Systems (WTORS) that have been installed in accordance
with the manufacturer's instructions and SAE J2249.
5. Attach WTORS to securement points (A) (B) in accordance
with the manufacturer's instructions and SAE J2249.
6. Attach occupant restraints in accordance with the
manufacturer's instructions and SAE J2249.
7. Ensure hip guides are mounted to lock in place.
8. Use only Wheelchair Tie-down (A, B) and Occupant
Restraint Systems (WTORS) which meet the requirements
of SAE J2249 Recommended Practice– Wheelchair Tie-down
and Occupant Restraint Systems For Use in Motor Vehicles.
Do not use WTORS designed to rely on the wheelchair
structure to transfer occupant restraint loads to the vehicle.
9. The wheelchair has been dynamically tested in a forward-fac-
ing mode for a 30 mph frontal impact test. The wheelchair
must be forward-facing during transport.
10. In order to reduce the potential of injury to vehicle occu-
pants, wheelchair-mounted accessories, such as trays and res-
piratory equipment, should be removed and secured sepa-
rately.
11. Postural supports and positioning devices should not be
relied on for occupant restraint.
12. Do not alter or substitute wheelchair frame parts, compo-
nents or seating.
13. Sudden stops or impacts can structurally damage your chair.
Chairs involved in such incidents should be replaced.
13
A
WARNING
A
MK-100158 Rev. A