Sharp AR-M236 Service Manual page 62

Detection size when 8.5" x 13" document/paper is used.
Employed unit
Document Document table/RSPF
Paper Machine paper feed cassette
Manual paper feed tray
A4/LT (8.5" x 11") detection enable/disable setup
In the inch series, Letter is detected as A4; in the AB series, A4 is detected as Letter.
Set value Setup
0 Detection invalid
1 Detection valid
Detection size when A4/LT (8.5" x 11") document/paper is used.
Employed unit
Document Document table/RSPF
Paper Machine paper feed cassette
Manual paper feed tray
26-3
Purpose Setting
Function Used to set the specifications of the auditor. Setting
(Purpose) must be made depending on the use condition of the
auditor.
Section Auditor
Item Specifications
Operation/procedure
Select the mode corresponding to the auditor specification mode with
the 10-key.
Item Content
0 P10 Built-in auditor mode
1 VENDOR Coin vendor mode
2 OTHER Others
When "1: VENDOR (Coin vendor mode)" is set, the following three
items of key operation setting are changed.
1) Set the LCD backlight change inhibit to "1: OFF (Enable)."
Destination
AB series (Japan)
AB series
Inch series
All destinations
Japan (AB series)
AB series
Inch series
Remarks
Default
Destination
AB series
Inch series
All destinations
All destinations
Setting
Default
range
0-2 0
AR-M236/M276/M237/M277 SIMULATION 8 - 23
Document size
0
(Invalid)
FC (8.5" x 13") B4
LG (8.5" x 14") B4
B4 B4
FC (8.5" x 13") B4
LG (8.5" x 14") B4
B4 B4
FC (8.5" x 13") LG (8.5" x 14")
LG (8.5" x 14") LG (8.5" x 14")
B4 WLT (11" x 17")
– Set with key operations.
FC (8.5" x 13") LG (8.5" x 14")
LG (8.5" x 14") LG (8.5" x 14")
B4 B4
FC (8.5" x 13") LG (8.5" x 14")
LG (8.5" x 14") LG (8.5" x 14")
B4 B4
FC (8.5" x 13") LG (8.5" x 14")
LG (8.5" x 14") LG (8.5" x 14")
B4 B4
Set value
Document size 0
(Invalid)
A4 A4
LT (8.5" x 11") A4
A4 LT (8.5" x 11")
LT (8.5" x 11") LT (8.5" x 11")
– Set with key operations.
– Regardless of the simulation setup.
2) When SIM 26-6 destination setting is set to "0: Japan," duplex copy
inhibit setting must be set to "0: ON (Inhibit)."
3) Set the sort automatic selection to "0: OFF (Disable)."
26-5
Purpose Setting
Function Used to set the count mode of the total counter and the
(Purpose) maintenance counter.
Item Specifications
Operation/procedure
Used to set the count up number (1 or 2) when an A3/WLT paper
passes through.
For the drum counter and the developer counter, double count is
employed unconditionally.
Set value
1
(Valid)
B4
B4
B4
FC (8.5" x 13")
FC (8.5" x 13")
FC (8.5" x 13")
FC (8.5" x 13")
FC (8.5" x 13")
WLT (11" x 17")
LG (8.5" x 14")
LG (8.5" x 14")
B4
FC (8.5" x 13")
FC (8.5" x 13")
B4
FC (8.5" x 13")
FC (8.5" x 13")
B4
1
(Valid)
LT (8.5" x 11")
LT (8.5" x 11")
A4
A4
Counter