Samsung Techwin. Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility.
Page 3
Before operating the camera, confirm the camera model and correct input power voltage. To help you understand this manual thoroughly, we'll introduce our model description. ■ SCV-5085 SERIES • NTSC MODEL • PAL MODEL SCV-5085N SCV-5085P ■ MODEL DESCRIPTION • SCV-5085X _ SIGNAL SYSTEM • SIGNAL SYSTEM...
Page 4
safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
Page 5
9. If this product fails to operate normally, contact the nearest service center. never disassemble or modify this product in any way. (samsung is not liable for problems caused by unauthorized modifications or attempted repair.) 10.
safety information FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus Samsung Techwin cares for the environment at all product manufacturing stages to preserve the environment, and is taking a number of steps to provide customers with more environment-friendly products.The Eco mark represents...
contents inTroDuCTion Features Components and Accessories COMPONENT NAMES AND FUNCTIONS insTallaTion Before installation Installation Adjusting the monitoring direction for the camera ConnECTion Connecting to Monitor Connecting to Power Using Coaxial Communications CamEra oPEraTion Menu Configuration Menu Setup TroublEshooTing Troubleshooting sPECifiCaTions Specifications Dimension 8_ contents...
Page 9
Without an external sensor, you can use this product to detect motion and generate alarms and thus more efficient monitoring can be achieved. y ssnr4 (samsung super noise reduction) function High performance W7 Chip removes noises of GAIN resulting from the low light level and shows a vivid, high definition video even in the dark place.
The camera’s OSD is complimented by 17 languages. - English, Chinese, Korean, Japanese, German, Italian, French, Spanish, Russian, Czech, Polish, Romanian, Serbian, Swedish, Danish, Turkish, Portuguese ComPonEnTs anD aCCEssoriEs Check if the following items are included in the product package. SCV-5085 Quick Manual FRONT SCV-5083 Quick Manual Screws 케이블...
ComPonEnT namEs anD funCTions Dome Cover shield Case rotate base : control rotating angle of camera. Cushion lens : It prevents the lens and dome cover from the external force generated ❹ during camera distribution.(Remove it before camera installation.) Vari-focal lens module : 3 ~ 8.5mm (F1.2). ❺...
Installation bEforE insTallaTion Ensure you read out the following instructions before installing the camera: y You have to check whether the location (ceiling or wall) can bear five times the weight of your camera. y Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it may cause a breakdown or fire.
Page 13
installing the camera on a ceiling or wall 1. Drill holes on the ceiling by matching to the holes on the case bed, and insert plastic anchors (HUD 5) (not included) fully into the holes. Fix the case bed on the ceiling by using Tapping screws (TH M4 x L30).
Page 14
3. Adjust the lens in a desired direction. 4. Secure the Shield case to the main unit. 5. Assemble the camera on its mounting bracket with the three screws using L Wrench. FRONT Shield case Dome cover The installation should be done by qualifi ed service personnel or system installers. If the ceiling material is not strong enough to hold the installation screws, the camera may fall off.
aDJusTing ThE moniToring DirECTion for ThE CamEra FRONT Tilt Lens rotation ` Adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling. Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called Tilt, and turning the lens on its axis is called Rotation.
ConnECTing To moniTor Connect the Video OUT port on the rear panel of the camera to a monitor. SCV-5085 Monitor y As the connecting method varies with the instruments, refer to the manual supplied with the instrument. y Only connect the cable when the power is turned off.
When the resistance value of copper wire is at [20°C(68°F)] Copper wire size (AWG) #24 (0.22mm #22 (0.33mm #20 (0.52mm #18 (0.83mm Resistance value(Ω/m) 0.078 0.050 0.030 0.018 Voltage Drop (V/m) 0.028 0.018 0.011 0.006 y As shown in the table above, voltage decreases as the wire gets longer. Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera.
Page 18
connection - Video Cable The camera's video output port is connected to the monitor with a BNC coaxial cable, shown below. If the distance between the camera and the monitor exceeds the recommended maximum, please use an auxiliary video amp. Recommended Cable Distance Specification...
camera operation mEnu ConfiguraTion main sETuP ● ● ● BASIC DAY/NIGHT BACKLIGHT PROFILE ● ● INDOOR ● USER SSDR ● ● ● ● OUTDOOR ● INDOOR WHITE BAL ● AWC SET ● MANUAL ● MERCURY ● BRIGHTNESS ● LENS ●...
Page 20
camera operation MAIN SETUP ▶ 1. PROFILE BASIC Select the function Change the status 2. SSDR using the Function using the Function 3. WHITE BAL Setup switch. Setup switch. 4. EXPOSURE 5. BACKLIGHT 6. SIMPLE FOCUS 7. SPECIAL 8. EXIT SAVE 1.
Page 21
If you select the ITS, the min shutter will be set to 1/200 sec. Noise can be detected at night. ssDr (samsung super Dynamic range) If an object has a large variance between bright and dark areas, it will keep bright areas bright and make selected dark areas bright, so that the overall brightness can be maintained.
Page 22
camera operation White bal (White balance) Use the White Balance function to adjust the screen color. 1. When the SETUP menu screen is MAIN SETUP displayed, select ‘White Bal’ by 1. PROFILE BASIC using the Function Setup switch so 2. SSDR that the arrow indicates ‘White Bal’...
Page 23
ExPosurE 1. When the SETUP menu screen is displayed, select ‘EXPOSURE’ by using the Function Setup switch so that the arrow indicates ‘EXPOSURE’. 2. Select a desired mode using the Function Setup switch. EXPOSURE SETUP ▶ BRIGHTNESS ---- ---- y brighTnEss : Adjusts the video LENS brightness.
Page 24
camera operation baCKlighT The camera uses our own W7 chips that are designed to clearly display the object and the background despite severe reverse light. 1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Function Setup switch. so that the arrow indicates ‘BACKLIGHT’. 2.
Page 25
y WDr : When there are both bright and dark areas at the same time, this mode makes both areas distinctive. - LEVEL : Select one from low, WDR SETUP med, high to adjust the LEVEL MIDDLE ▶ 1. brightness of the WDR RETURN setup.
Page 26
camera operation simPlE foCus 1. When the SETUP menu screen is displayed, select ‘SIMPLE FOCUS’ by using the Function Setup switch. so that the arrow indicates ‘SIMPLE FOCUS’. 2. Select a desired mode using the SIMPLE FOCUS Function Setup switch depending on + 1.
Page 27
sPECial 1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function Setup switch so that the arrow indicates ‘SPECIAL’. 2. Select a desired mode using the SPECIAL SETUP Function Setup switch. DISPLAY ▶ 1. y DisPlaY COMM ADJ IMAGE ADJ ❶M...
camera operation - FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue) - LANGUAGE : You can select the menu language according to your requirements. - RETURN : Return to the SPECIAL menu. y Comm aDJ (Communication adjustment) : - COAX : You can select whether to COMM SETUP use COAX communication.
Page 29
y DaY/nighT : You can display pictures in color or in black and white. ❶ If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates ‘DAY/NIGHT’. ❷ Select a desired mode using the Function Setup switch according to the picture display you want.
camera operation - Manual : Depending on the defog DEFOG MANUAL SETUP level set by the user, adjust LEVEL MIDDLE ▶ the clarity of image. (LOW, RETURN MIDDLE, HIGH) - OFF : Released state If the defog mode is set to Auto, and if the amount of fog is reduced, the function level will be also reduced.
Page 31
- TAMPERING : If the screen view TAMPERING is obstructed or the SENSITIVITY MIDDLE ▶ camera location ALARM OUT is changed, RETURN tampering detection, you can issue an event signal by setting it. y SENSITIVITY : Set the sensitivity to tampering detection. y ALARM OUT : Outputting of detection signals can be set.
Page 32
camera operation use the selected area. ` SENSITIVITY : Set the sensitivity of the motion detection. When you adjust the higher level, the more sensitive. ` TOP/BOTTOM/LEFT/RIGHT : Area location can be adjusted. ` RETURN : Return to the MOTION DET menu. y NON DET.
Page 33
to use the fence selected in the FENCE. ` TYPE : Two types, line and area, of fences are available. ` POSITION : Defines the position and detection direction of a line or fenced area. 1) LINE FENCE - SEL POS : Selects a LINE FENCE position from SEL POS...
Page 34
camera operation In the following cases, the appear/indicator may malfunction. - When multiple movements occur randomly - When a fixed object keeps moving in the same location - When a new object covers an object with changes y ALARM OUT : When object movement is detected, the detection signal will be outputted.
Page 35
- If the size is greater than the max size or smaller than the min size, motion is not detected. To avoid false detection caused by noises, set the max/min detection size suitable for the installation environment. But the same movement in the same location can cause a different detection size. So, include margins when you set the min/max detection size.
Page 36
troubleshooting TroublEshooTing If you have trouble operating your camera, refer to the following table. If the guidelines do not enable you to solve the problem, contact an authorized technician. Problems Troubleshooting Nothing appears on the screen. y Check that the power cord and line connection between the camera and monitor are properly connected.
Page 37
specifications sPECifiCaTions sCV-5085n sCV-5085P Video Imaging Device 1/3” 1.3M CMOS Total Pixels 1312(H) x 1069(V) Effective Pixels 1305(H) x 1049(V) Progressive Scan Scanning System Synchronization Internal Frequency H : 15.734KHz / V : 59.94Hz H : 15.625KHz / V : 50Hz Color : 1000 TVL Horizontal Resolution B/W : 1000 TVL...
Page 38
specifications sCV-5085n sCV-5085P Defog AUTO / MANUAL / OFF Purple Fringe Reduction ( Off / Low / Middle / High) Purple Fringe Reduction Digital Image Stabilization Off / On Off / On Tampering Off / On Motion Detection Fence, Apear_Disappear, Counting ( Off / On ) Intelligent Video Privacy Masking Off / On (24 programmable zones with 4points polygonal masking)