Table of Contents
Advertisement
Quick Links
For Quick
For Quick
SmartNode 5200
Enterprise Session Border Router
User Manual
Important
This is a Class A device and is intended for use in a light industrial (commercial) environment only. It is not intended nor approved for
use in a heavy industrial or residential environment.
This device is approved for connection to the public ISDN telecommunication network, over BRI/S0-ISDN interfaces.
Sales Office:
+1 (301) 975-1000
Technical Support:
+1 (301) 975-1007
E-mail:
support@patton.com
WWW:
www.patton.com
Part Number: 07MSN5200-GSG, Rev. B
Revised: February 6, 2012
Advertisement
Table of Contents
Related Manuals for Patton SmartNode 5200
Summary of Contents for Patton SmartNode 5200
-
Page 1: User Manual
For Quick For Quick SmartNode 5200 Enterprise Session Border Router User Manual Important This is a Class A device and is intended for use in a light industrial (commercial) environment only. It is not intended nor approved for use in a heavy industrial or residential environment. - Page 2 Under no condition shall Patton Electronics be liable for any damages incurred by the use of this product. These damages include, but are not limited to, the following: lost profits, lost savings and incidental or consequential damages arising from the use of or inability to use this product.
-
Page 3: Summary Table Of Contents
18 SmartNode installation..........................20 Initial configuration ............................25 Contacting Patton for assistance ........................31 Compliance information ..........................34 Specifications ..............................36 Cabling ................................. 39 Port pin-outs ..............................41 SmartNode 5200 factory configuration ......................43 End user license agreement ........................... 48... -
Page 4: Table Of Contents
General observations ............................12 Typographical conventions used in this document....................13 General conventions ............................13 General information ............................14 SmartNode 5200 overview ............................15 SmartNode 5200 rear panel ..........................16 SmartNode 5200 front panel ..........................17 Applications overview............................ 18 Introduction ................................19 Typical application ..............................19 SmartNode installation.......................... - Page 5 Contacting Patton for assistance ........................31 Introduction ................................32 Contact information..............................32 Patton support headquarters in the USA ......................32 Alternate Patton support for Europe, Middle East, and Africa (EMEA) ............32 Warranty Service and Returned Merchandise Authorizations (RMAs)..............32 Warranty coverage ............................32 Out-of-warranty service ..........................33 Returns for credit ............................33...
- Page 6 SmartNode 5200 User Manual Table of Contents End user license agreement ........................... 48 End User License Agreement ..........................49 1. Definitions ..............................49 2. Title ................................49 3. Term ................................49 4. Grant of License ............................49 5. Warranty ..............................49 6. Termination ..............................50 7. Other licenses...
-
Page 7: List Of Figures
SmartNode 5200 front panel ........ -
Page 8: List Of Tables
SmartNode 5200 LED definitions ........ -
Page 9: About This Guide
About this guide This guide describes the SmartNode 5200 hardware, installation and basic configuration. For detailed software configuration information refer to the SmartWare Software Configuration Guide and the available Configura- tion Notes. Audience This guide is intended for the following users: •... -
Page 10: Precautions
SmartNode 5200 User Manual About this guide Precautions Notes, cautions, and warnings, which have the following meanings, are used throughout this guide to help you become aware of potential problems. Warnings are intended to prevent safety hazards that could result in per- sonal injury. -
Page 11: Safety When Working With Electricity
SmartNode 5200 User Manual About this guide Safety when working with electricity • Do not open the device when the power cord is connected. For systems without a power switch and without an external power adapter, line volt- ages are present within the device when the power cord is connected. -
Page 12: General Observations
SmartNode 5200 User Manual About this guide Electrostatic Discharge (ESD) can damage equipment and impair electrical cir- cuitry. It occurs when electronic printed circuit cards are improperly handled and can result in complete or intermittent failures. Do the following to prevent ESD: •... -
Page 13: Typographical Conventions Used In This Document
SmartNode 5200 User Manual About this guide Typographical conventions used in this document This section describes the typographical conventions and terms used in this guide. General conventions The procedures described in this manual use the following text conventions: Table 1. General conventions... -
Page 14: General Information
Chapter 1 General information Chapter contents SmartNode 5200 overview ............................15 SmartNode 5200 rear panel ..........................16 SmartNode 5200 front panel ..........................17... -
Page 15: Smartnode 5200 Overview
Figure 1. SmartNode 5200 The SmartNode 5200 is equipped with a 10/100Base-T Ethernet WAN port and an integrated 4-port 10/100Base-T Ethernet switch. The SmartNode 5200 Enterprise Session Border Router performs the following major functions: •... -
Page 16: Smartnode 5200 Rear Panel
SmartNode 5200 User Manual 1 • General information SmartNode 5200 rear panel The SmartNode 5200 is a compact VoIP Gateway Router that supports 32 simultaneous SIP sessions. The SmartNode 5200 rear panel ports are described in table Model SN5200 WAN ETH 0/0... -
Page 17: Smartnode 5200 Front Panel
SmartNode 5200 User Manual 1 • General information Figure 3. SmartNode 5200 front panel SmartNode 5200 front panel Figure 3 shows SmartNode 5200 LEDs, the LED definitions are listed in table Table 3. SmartNode 5200 LED definitions Description Note If an error occurs, all LEDs will flash once per second. -
Page 18: Applications Overview
Chapter 2 Applications overview Chapter contents Introduction ................................19 Typical application ..............................19... -
Page 19: Introduction
2 • Applications overview Introduction Patton’s SmartNode VoIP Enterprise Session Routers deliver the features you need for advanced multiservice voice and data network applications. They combine high quality voice-over-IP with powerful quality of service routing functions to build professional and reliable VoIP and data networks. This chapter describes typical applications for which this SmartNode is uniquely suited. -
Page 20: Smartnode Installation
Chapter 3 SmartNode installation Chapter contents Planning the installation............................21 Site log ................................21 Network information ............................21 Network Diagram ............................21 IP related information .............................22 Software tools ..............................22 Power source ..............................22 Location and mounting requirements ......................22 Installing the gateway router..........................22 Placing the SmartNode ...........................22 Installing cables ...............................23... -
Page 21: Planning The Installation
22 to install the device. Site log Patton recommends that you maintain a site log to record all actions relevant to the system, if you do not already keep such a log. Site log entries should include information such as listed in table Table 4. -
Page 22: Ip Related Information
SmartNode 5200 User Manual 3 • SmartNode installation IP related information Before you can set up the basic IP connectivity for your SmartNode 5200 you should have the following infor- mation: • IP addresses used for Ethernet LAN and WAN ports •... -
Page 23: Installing Cables
23) Connecting the 10/100Base-T Ethernet LAN and WAN cables The SmartNode 5200 has automatic MDX (auto-crossover) detection and configuration on all Ethernet ports. Any of the ports can be connected to a host or hub/switch with a straight-through wired cable. -
Page 24: Router Front Panel Leds
SmartNode 5200 User Manual 3 • SmartNode installation Power LAN ports 1–4 activity Figure 5. Router front panel LEDs 4. Verify that the green Power LED is lit (see figure Congratulations, you have finished installing the SmartNode Gateway Router! Now go to chapter 4, “Initial... -
Page 25: Initial Configuration
Chapter 4 Initial configuration Chapter contents Introduction ................................26 Connecting the SmartNode to your laptop PC......................26 Configuring the desired IP address ........................27 Factory-default IP settings ..........................27 Login ................................27 Changing the WAN IP address ........................27 Connecting the SmartNode to the network ......................28 Loading the configuration (optional) ........................29 Additional... -
Page 26: Introduction
The SmartNode 5200 Series is equipped with Auto-MDX Ethernet ports, so you can use straight-through cables for host or hub/switch connections (see figure... -
Page 27: Configuring The Desired Ip Address
SmartNode 5200 User Manual 4 • Initial configuration Configuring the desired IP address Factory-default IP settings The factory default configuration for the Ethernet interface IP addresses and network masks are listed in table Both Ethernet interfaces are activated upon power-up. LAN interface ETH 0/1 (LAN) provides a default DHCP server, the WAN interface uses DHCP client to automatically assign the IP address and network mask. -
Page 28: Connecting The Smartnode To The Network
In general, the SmartNode will connect to the network via the WAN (ETH 0/0) port. This enables the Smart- Node to offer routing services to the PC hosts on LAN (ETH 0/1) port. The SmartNode 5200 Series is equipped with Auto-MDX Ethernet ports, so you can use straight-through or crossover cables for host or... -
Page 29: Loading The Configuration (Optional)
Guide.) Loading the configuration (optional) Patton provides a collection of configuration templates on the support page at www.patton.com/smart- node—one of which may be similar enough to your application that you can use it to speed up configuring the SmartNode. Simply download the configuration note that matches your application to your PC. Adapt the configuration as described in the configuration note to your network (remember to modify the IP address) and copy the modified configuration to a TFTP server. -
Page 30: Additional Information
SmartNode 5200 User Manual 4 • Initial configuration 172.16.1.99(if-ip)[eth0]#reload Running configuration has been changed. Do you want to copy the 'running-config' to the 'startup-config'? Press 'yes' to store, 'no' to drop changes : no Press 'yes' to restart, 'no' to cancel : yes... -
Page 31: Contacting Patton For Assistance
Contacting Patton for assistance Chapter contents Introduction ................................32 Contact information..............................32 Patton support headquarters in the USA ......................32 Alternate Patton support for Europe, Middle East, and Africa (EMEA) ............32 Warranty Service and Returned Merchandise Authorizations (RMAs)..............32 Warranty coverage ............................32 Out-of-warranty service ..........................33 Returns for credit ............................33... -
Page 32: Introduction
RAS warranty and obtaining a return merchandise authorization (RMA). Contact information Patton Electronics offers a wide array of free technical services. If you have questions about any of our other products we recommend you begin your search for answers by using our technical knowledge base. Here, we have gathered together many of the more commonly asked questions and compiled them into a searchable database to help you quickly solve your problems. -
Page 33: Out-Of-Warranty Service
RMA#: xxxx 7622 Rickenbacker Dr. Gaithersburg, MD 20879-4773 USA Patton will ship the equipment back to you in the same manner you ship it to us. Patton will pay the return shipping costs. Warranty Service and Returned Merchandise Authorizations (RMAs) -
Page 34: A Compliance Information
Appendix A Compliance information Chapter contents Compliance ................................35 ................................35 Low-Voltage Directive (Safety) ........................35 PSTN Regulatory ............................35 CE Declaration of Conformity ..........................35 Authorized European Representative ........................35... -
Page 35: Compliance
SmartNode 5200 User Manual A • Compliance information Compliance • EN55022, Class A • EN55024 Low-Voltage Directive (Safety) • IEC/EN60950-1, 2nd edition • AS/NZS60950-1 PSTN Regulatory • TBR 3:1995 A1 • AS/ACIF S031:2001 CE Declaration of Conformity This device conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual recogni- tion of their conformity. - Page 36 Appendix B Specifications Chapter contents Data connectivity ..............................37 Voice signalling ..............................37 services................................37 Management .................................37 Operating environment ............................38 Operating temperature ............................38 Operating humidity ............................38 System...................................38 Dimensions ................................38 Weight and power dissipation ..........................38...
-
Page 37: B Specifications
Manual Key; IKE optional AES/DES/3DES Encryption Note To use the IPSec VPN capabilities including AES/DES/3DES encryption with the SmartNode 5200, you may need to purchase additional license keys. Note The SmartNode 4562 is loaded with the VPN license from the factory. Management... -
Page 38: Operating Environment
SmartNode 5200 User Manual B • Specifications Built-in diagnostic tools (trace, debug) Operating environment Operating temperature 32–104°F (0–40°C) Operating humidity 5–80% (non condensing) System CPU Motorola MC875 operating at 66 MHz Memory: • 16 Mbytes SDRAM • 4 Mbytes Flash Dimensions 7.3W x 1.6H x 6.1D in. -
Page 39: Cabling
Appendix C Cabling Chapter contents Introduction ................................40 Ethernet ................................40... -
Page 40: Introduction
SmartNode 5200 User Manual C • Cabling Introduction This section provides information on the cables used to connect the SmartNode and the interface cards to the existing network infrastructure and to third party products. Ethernet Ethernet devices (10Base-T/100Base-T) are connected to the SmartNode over a cable with RJ-45 plugs. All Ethernet ports on the SN5200 &... -
Page 41: Port Pin-Outs
Appendix D Port pin-outs Chapter contents Introduction ................................42 Ethernet ................................42... -
Page 42: Introduction
SmartNode 5200 User Manual D • Port pin-outs Introduction This section provides pin-out information for the ports of the SmartNode. Ethernet Table 7. RJ-45 socket Signal Note Pins not listed are not used. Introduction... -
Page 43: Smartnode 5200 Factory Configuration
Appendix E SmartNode 5200 factory configuration Chapter contents Introduction ................................44... -
Page 44: Introduction
SmartNode 5200 User Manual E • SmartNode 5200 factory configuration Introduction The factory configuration settings for SmartNode 5200 are as follows: #----------------------------------------------------------------# # 5200 # R3.xx BUILDxxxxx SIP # 2005-08-25T00:00:00 # Factory configuration file #----------------------------------------------------------------# dns-client server 10.56.128.44 dns-relay webserver port 80 language en sntp-client sntp-client server primary 129.132.2.21 port 123 version 4... - Page 45 SmartNode 5200 User Manual E • SmartNode 5200 factory configuration default-router 1 192.168.1.1 domain-name-server 1 192.168.1.1 profile aaa default method 1 local method 2 none context ip router interface eth0 ipaddress 10.10.10.10 255.255.254.0 use profile napt NAPT tcp adjust-mss rx mtu...
- Page 46 SmartNode 5200 User Manual E • SmartNode 5200 factory configuration location-service LS-LAN domain 1 10.10.10.10 identity 37060 authentication outbound authenticate 1 authentication-service AUTHSERV username 37060 authentication inbound authenticate 1 authentication-service AUTHSERV username 37060 registration inbound identity 37061 authentication outbound authenticate 1 authentication-service AUTHSERV username 37061...
- Page 47 SmartNode 5200 User Manual E • SmartNode 5200 factory configuration call outbound call inbound identity 37060 inherits IDENT-GROUP-WAN registration outbound identity 37061 inherits IDENT-GROUP-WAN registration outbound identity 37062 inherits IDENT-GROUP-WAN registration outbound identity 37063 inherits IDENT-GROUP-WAN registration outbound context sip-gateway GWSIP-WAN...
-
Page 48: F End User License Agreement
Appendix F End user license agreement Chapter contents End User License Agreement ..........................49 1. Definitions ..............................49 2. Title ................................49 3. Term ................................49 4. Grant of License ............................49 5. Warranty ..............................49 6. Termination ..............................50 7. Other licenses .............................50... -
Page 49: End User License Agreement
Program(s), even if Patton Electronics Company has been advised of the possibil- ity of such damages. Because some states do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitation may not apply to you. -
Page 50: Termination
The End User may terminate this agreement by returning the Designated Equipment and destroying all copies of the licensed Program(s). Patton Electronics Company may terminate this Agreement should End User violate any of the provi- sions of section “4. Grant of License”...
Need help?
Do you have a question about the SmartNode 5200 and is the answer not in the manual?
Questions and answers