Epson Stylus PHOTO RX510 Service Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. All in One Printer
  5. Stylus Photo RX510
  6. Service manual

Epson Stylus PHOTO RX510 Service Manual

Hide thumbs Also See for Stylus PHOTO RX510:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual , Setup Manual

SERVICE MANUAL

Scanner
Printer
Copier
•
•
EPSON Stylus PHOTO RX500/510
SEOT03007
Download Service Manual And Resetter Printer at http://printer1.blogspot.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Stylus PHOTO RX510 and is the answer not in the manual?

Questions and answers

Related Manuals for Epson Stylus PHOTO RX510

Summary of Contents for Epson Stylus PHOTO RX510

  • Page 1: Service Manual

    SERVICE MANUAL Scanner Printer Copier • • EPSON Stylus PHOTO RX500/510 SEOT03007 Download Service Manual And Resetter Printer at http://printer1.blogspot.com...
  • Page 2 The contents of this manual are subject to change without notice. All effort have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON would greatly appreciate being informed of them.
  • Page 3 2. MAKE CERTAIN THAT THE SOURCE VOLTAGES IS THE SAME AS THE RATED VOLTAGE, LISTED ON THE SERIAL NUMBER/RATING PLATE. IF THE EPSON PRODUCT HAS A PRIMARY AC RATING DIFFERENT FROM AVAILABLE POWER SOURCE, DO NOT CONNECT IT TO THE POWER SOURCE.

  • Page 4: About This Manual

    C H E C K condition that is necessary to accomplish a task efficiently. It may P O I N T Epson-approved lubricants and adhesives required for servicing also provide additional information that is related to a specific the product.
  • Page 5 Revision Status Revision Date of Issue Description September 16, 2003 First release February 2, 2004 CHAPTER 1 PRODUCT DESCRIPTION • Outside Drawing is added to 1.2.7 Weight and Overall Dimensions (p.11). CHAPTER 2 OPERATING PRINCIPLES • 2.2.1.2 Printerhead Specification (p.15) is added.

  • Page 6: Table Of Contents

    EPSON Stylus PHOTO RX500/510 Revision B CONTENTS Chapter 1 Product Description 3.1.2 Preliminary Checks ................... 20 3.2 Troubleshooting at Unit Level ................. 21 1.1 Overview ......................9 3.2.1 Printer / Scanner does not operate at all 1.1.1 Basic Functions ................... 9 even with power turned on ................
  • Page 7 EPSON Stylus PHOTO RX500/510 Revision B 4.4.4 HP Sensor Circuit Board ................48 5.2.4 Check Pattern print ................... 76 5.2.4.1 Normal Paper Pattern ................ 76 4.5 Disassembly and Assembly of Printer Unit ............ 49 5.2.4.2 Photo Quality Paper Pattern .............. 76 4.5.1 CR Scale ....................

  • Page 8: Product Description

    C H A P T E R PRODUCT DESCRIPTION Download Service Manual And Resetter Printer at http://printer1.blogspot.com...

  • Page 9: Chapter 1 Product Description

    Six color independent ink cartridge Reduces 2 pages/4 pages of the original image to 2-up/4 up copy single page. BorderFree print on Epson special paper Flips over the original left to right. Low noise Mirror copy Alarms to prevent paper jam when stacker (output tray) is closed Adjusts image to wallet size (3.5”...

  • Page 10: Common

    EPSON Stylus PHOTO RX500/510 Revision C 1.2 Common 1.2.2 Interface USB 2.0 compatible. See Table 1-2. for details. The specifications described below are common to the scanner and printer. Table 1-2. 1.2.1 Electrical Specifications Item Descriptions Standard “Universal Serial Bus Specifications Revision 2.0”...

  • Page 11: Environmental Conditions

    EPSON Stylus PHOTO RX500/510 Revision C 1.2.4 Environmental Conditions 1.2.7 Weight and Overall Dimensions Weight: Table 1-4. 9.8 kg (Excluding ink cartridge) Operating Storage Transporting Overall Dimensions (mm): 10 ~ 35 °C -20°C ~ 60 °C Temperature - 20°C ~ 40°C 455.9 x 439.1 x 256.0 (Width x Depth x Height)

  • Page 12: Ink Cartridge

    EPSON Stylus PHOTO RX500/510 Revision C 1.3 Ink Cartridge Type: Ink cartridge Suggested effective period: Period described on the product package, or six months after opening. Storage temperature Storage: -30°C ~ 40°C (If 40°C, within 1 month) Transporting: -30°C ~ 50°C (If 50°C, within 10 days) When installed: -20°C ~ 40°C (If 40°C, within 1 month,...

  • Page 13: Chapter 2 Operating Principles

    C H A P T E R OPERATING PRINCIPLES Download Service Manual And Resetter Printer at http://printer1.blogspot.com...

  • Page 14: Overview

    EPSON Stylus PHOTO RX500/510. Paper Eject Unit EPSON Stylus PHOTO RX500/510 mainly, basically consists of a printer and a scanner. The mechanism can be divided into the printer and the scanner. The electric circuit includes the Main Board circuit, Power Supply Board circuit, scanner carriage circuit and control panel circuit.

  • Page 15: Carriage Motor Specification

    EPSON Stylus PHOTO RX500/510 Revision C 2.2.1.1 Carriage Motor Specification 2.2.1.4 PW Detector Specification Stylus PHOTO RX500/510 has newly employed a PW (Paper Width) sensor that is Table 2-1. CR Motor Specification described in detail below. Item Specifications Purpose of Detection...

  • Page 16: Scanner Mechanism

    EPSON Stylus PHOTO RX500/510 Revision C Controlling of each detection 2.2.2 Scanner Mechanism Table 2-3. The scanner consists of the Scanner Carriage Unit comprising the CCD for capturing images and the light source for illuminating the document, the Scanner Motor and...

  • Page 17: Electric Circuit

    EPSON Stylus PHOTO RX500/510 Revision C 2.3 Electric Circuit The electric circuit boards of Stylus PHOTO RX500/510 are as follows: C544MAIN Board (main circuit board) C543PSB Board / C543PSE Board (power supply circuit board) CCD circuit board (Scanner circuit board) Panel circuit board Figure 2-4.

  • Page 18: C544 Main Circuit Board

    EPSON Stylus PHOTO RX500/510 Revision C 2.3.1 C544 Main Circuit Board Table 2-4. Main Element location Function 2.3.1.1 Feature • Built-in NA85E2C core USB 2.0 with multi-end points allows high speed SPC without HUB • Built-in iLB RAM 12Kbyte, Built-in dLB RAM 4Kbyte...

  • Page 19: Troubleshooting

    C H A P T E R TROUBLESHOOTING Download Service Manual And Resetter Printer at http://printer1.blogspot.com...

  • Page 20: Overview

    Monitor 3” installed on the host personal computer. The power supply voltage must be within the specification limits. (Measure the Once an error occurs, the “EPSON Status Monitor 3” will appear as a pop-up window voltage at the wall socket.) on the screen of the host PC.

  • Page 21: Troubleshooting At Unit Level

    EPSON Stylus PHOTO RX500/510 Revision C 3.2 Troubleshooting at Unit Level Table 3-1. LCD Indication LED Indication By following this troubleshooting procedure, when some trouble has occurred, you can Error Status LCD Indication Error Power easily identify the unit which is the cause of the trouble, from its observation. Table 3-1 Table 3-2 list the observations of various troubles.

  • Page 22: Printer / Scanner Does Not Operate At All Even With Power Turned On

    EPSON Stylus PHOTO RX500/510 Revision C 3.2.1 Printer / Scanner does not operate at all Table 3-2. Observations and Troubleshooting Flowcharts even with power turned on Observation Details Refer to Power is on but not • LED does not turn on at all.

  • Page 23: Error Is Detected

    EPSON Stylus PHOTO RX500/510 Revision C 3.2.2 Error is detected 3.2.3 Trouble related to Print Start Start Execute test printing Check error contents by LCD (See Table 3-1). Printing was successfully done? Turn power off, unlock CR and move CR with...

  • Page 24: Paper Feeding Is Not Normally Carried Out

    EPSON Stylus PHOTO RX500/510 Revision C 3.2.4 Paper feeding is not normally carried out 3.2.5 Operation Panel faulty Start Start Operation Paper is Panel is connected correctly set in properly with ASF? cable? Set paper correctly. Connect correctly Operation panel again.

  • Page 25: Troubleshooting For Printer

    EPSON Stylus PHOTO RX500/510 Revision C 3.3 Troubleshooting for Printer Table 3-3. Printer Errors (continued) Observation Cause Remedy This section describes repair / service of the Printer Mechanism. Listed below are Ink cartridge out • If Ink cartridge is not correctly •...
  • Page 26 EPSON Stylus PHOTO RX500/510 Revision C Troubleshooting without error display on LCD. For Items and pages, refer the following: • Faulty pump mechanism (p26) • Ink is not absorbed at all or ink absorption is poor. (p26) • Faulty carriage operation (p27) •...
  • Page 27 EPSON Stylus PHOTO RX500/510 Revision C Faulty carriage operation Table 3-6. Diagnostics when carriage action is abnormal Condition Cause Check Point Remedy When power is turned on, There is an obstacle in CR shift area. Check with the naked eye whether there is an obstacle.
  • Page 28 EPSON Stylus PHOTO RX500/510 Revision C Faulty print Table 3-8. Diagnostics when printing is abnormal Condition Cause Check Point Remedy Faulty printing occurs at Head surface is dirty. Repeat cleaning and test printing alternately several times. Clean with a swab fixed to a stick.
  • Page 29 EPSON Stylus PHOTO RX500/510 Revision C Table 3-8. Diagnostics when printing is abnormal (continued) Condition Cause Check Point Remedy White line appears in output Dirt is adhering to CR guide shaft. Check whether dirt is adhering to the surface of CR guide Clean the surface of CR guide shaft with a dry and soft cloth.
  • Page 30 EPSON Stylus PHOTO RX500/510 Revision C Faulty paper loading Table 3-9. Diagnostics when feeder is abnormal Condition Cause Check Point Remedy Paper is not loaded. Paper loading roller worn Check whether paper loading roller rotates when paper Clean the paper loading roller with the cleaning sheet. If this feeding is not operating.
  • Page 31 EPSON Stylus PHOTO RX500/510 Revision C Printer stops during initialization Table 3-11. Diagnostics when printer stops during format Condition Cause Check Point Remedy Printer error is indicated. Faulty PE sensor Check PE sensor signal level. Replace the PE sensor (Refer to Table 3-22 “Sensor Check”...

  • Page 32: Troubleshooting For Scanner

    EPSON Stylus PHOTO RX500/510 Revision C 3.4 Troubleshooting for Scanner Observation of Trouble and Reference for Remedy Table 3-13. Observation of Trouble and Reference for Remedy This section describes repair / service for the Scanner mechanism. In troubleshooting, Reference for first the trouble is identified at the unit level based on the observation.
  • Page 33 EPSON Stylus PHOTO RX500/510 Revision C Carriage unit does not operate Fluorescent lamp does not turn on Table 3-15. Carriage unit does not operate Table 3-17. Fluorescent lamp does not turn on Cause Check Point Yes/No Remedy Cause Check Point...

  • Page 34: I/F Concerned Troubleshooting

    EPSON Stylus PHOTO RX500/510 Revision C 3.5 I/F Concerned Troubleshooting Failure diagnosis concerned with Memory Card Slot Table 3-20. Failure diagnosis concerned with Memory Card This section describes the failure diagnosis on USB Interface, Memory Card Slot. Cause Check Point...

  • Page 35: Troubleshooting For Motors And Sensors

    EPSON Stylus PHOTO RX500/510 Revision C 3.6 Troubleshooting for Motors and Sensors Motor Resistance and Check Point Table 3-21. Motor Resistance and Check Point Section Motor Name Location Check Point Printer CR motor CN11 Pin 1 & 3 (Main board)

  • Page 36: Disassembly And Assembly

    C H A P T E R DISASSEMBLY AND ASSEMBLY Download Service Manual And Resetter Printer at http://printer1.blogspot.com...

  • Page 37: Overview

    EPSON Stylus PHOTO RX500/510 Revision C 4.1 Overview 4.1.1 Precautions See the precautions given under the handling “WARNING” and “CAUTION” in the This section describes procedures for disassembling the main components of the following column before disassembling and assembling the product.

  • Page 38: Tools

    EPSON Stylus PHOTO RX500/510 Revision C 4.1.3 Screws Use only recommended tools for disassembling, assembling or C A U T I O N Table 4-2. Screws adjusting the printer. Description Appearance Observe the specified torque when tightening screws. CBP-Tite *x* F/Ni Apply lubricants and adhesives as specified.

  • Page 39: Service Dispatch Standard

    EPSON Stylus PHOTO RX500/510 Revision C 4.1.4 Service Dispatch Standard Table 4-3. Check List (continued) Classification Part Check item Check column When this machine is completely repaired and returned to the user, confirm finally Lubrication Designated Lubrication is done at designated according to Check list in Table 4-3.

  • Page 40: Stylus Photo Rx500/510 Disassembly

    EPSON Stylus PHOTO RX500/510 Revision C 4.1.5 Stylus PHOTO RX500/510 Disassembly The flowchart below shows step-by-step disassembly procedure. When disassembling each component, refer to the page number shown in the figure. 4.2 Main Unit Removal (p.41) Disassembly and Assembly of Main Unit START 4.6Disassembly and Assembly of Other Parts (p59)

  • Page 41: Main Unit Removal

    EPSON Stylus PHOTO RX500/510 Revision C 4.2 Main Unit Removal 4.2.1 Panel Unit Removal Operation Panel Remove a USB cable from the Stylus PHOTO RX500/510 unit. Panel Unit Remove the operation panel from the panel unit. Remove two screws securing the panel unit.

  • Page 42: Scanner Unit Removal

    EPSON Stylus PHOTO RX500/510 Revision C 4.2.2 Scanner Unit Removal C.B.P.Tite 3x8,F/ZN ⋅ Tightening torque:0.6 ± 0.1 N Panel Unit Removal. (p41) Scanner Unit Remove one screw that secures the FFC cover. Remove the FFC cover from the middle housing.

  • Page 43: Middle Housing Removal

    EPSON Stylus PHOTO RX500/510 Revision C 4.2.3 Middle Housing Removal C.B.P Tite 3x10,F/ZN ⋅ Tightening torque:0.6 ± 0.1 N Scanner Unit Removal. (p42) Middle Housing Remove all connectors from the main board. Remove one screw that secures a tube cover, and remove it from the printer unit.
  • Page 44 EPSON Stylus PHOTO RX500/510 Revision C Pay attention when handling the connector while installing the middle housing. After installing the Middle Housing, remove the Tube Cover once and make certain that the tube is inserted into the Porous Pad properly.

  • Page 45: Disassembly And Assembly Of Panel Unit

    EPSON Stylus PHOTO RX500/510 Revision C 4.3 Disassembly and Assembly of Panel Unit 4.3.1 Panel Circuit Board Removal Front Middle Cover Panel Unit Removal. (p41) Remove one screw that secures the grounding plate. Remove the grounding plate from the panel shield plate.

  • Page 46: Disassembly And Assembly Of Scanner Unit

    EPSON Stylus PHOTO RX500/510 Revision C 4.4 Disassembly and Assembly of Scanner Unit Lubrication required. For lubrication, refer to the following section. 6.3.2 Lubrication Points of the Scanner (p81) START Panel Unit Removal (p.41) Scanner Unit Removal (p.42) Upper Housing Assembly Removal (p47)

  • Page 47: Upper Housing Assembly Removal

    EPSON Stylus PHOTO RX500/510 Revision C 4.4.1 Upper Housing Assembly Removal TPU Assembly Scanner Unit Removal. (p42) Remove the TPU assembly. Remove four hinge screws. Remove a hinge from the scanner unit. Unlock the carriage. Remove eight screws on bottom of the scanner unit.

  • Page 48: Ccd Module

    EPSON Stylus PHOTO RX500/510 Revision C 4.4.2 CCD Module Timing Clamp Timing Belt Upper Housing Assembly Removal. (p47) Remove a driven pulley from a timing belt by pressing the driven pulley Assembly C.B.P Tite 3x8,F/ZN ⋅ Tightening torque:0.7 ± 0.1 N to loose tension of a timing belt.

  • Page 49: Disassembly And Assembly Of Printer Unit

    EPSON Stylus PHOTO RX500/510 Revision C 4.5 Disassembly and Assembly of Printer Unit Carriage concerned START Paper feeding concerned Other parts Panel Unit Removal (p.41) Scanner Unit Removal (p.42) Middle Housing Removal (p.43) CR Scale (p50) ASF Unit Removal (p54)

  • Page 50: Cr Scale

    EPSON Stylus PHOTO RX500/510 Revision C 4.5.1 CR Scale Extension Spring, CR Scale When handling the CR scale, hold both ends, or top and bottom C A U T I O N only. Do not touch the reading surface. Pay attention to keeping out of stains or scratches on the reading surface.

  • Page 51: Carriage Unit

    EPSON Stylus PHOTO RX500/510 Revision C 4.5.2 Carriage Unit C.B.S Tite R 3x4,F/ZN Tightening torque Ffc Holder Middle Housing Removal. (p43) ⋅ :0.8 ± 0.1 N CR Scale Removal. (p50) C.B.S Tite 3x6,F/ZN ⋅ Remove two screws on the left side of the FFC holder, and remove it from the Tightening torque:0.5 ±...
  • Page 52 EPSON Stylus PHOTO RX500/510 Revision C Remove the CR belt from the CR motor. Remove a torsion spring from the carriage unit, and remove the carriage lever from right side. Unhook nine locations that secure the carriage unit to the head cable cover, and Carriage remove the head cable cover.

  • Page 53: Printhead

    EPSON Stylus PHOTO RX500/510 Revision C 4.5.3 Printhead Carriage Unit Removal. (p51) Remove the Head Cable from the CSIC board, then remove the Head Cable from Head Cable the Holder I/C. Remove the Printhead and Carriage from the Holder I/C.

  • Page 54: Asf Unit Removal

    EPSON Stylus PHOTO RX500/510 Revision C 4.5.4 ASF Unit Removal ASF Unit Middle Housing Removal. (p43) C.B.S TITE (P4) R 3x6,F/ZN Remove three screws that secure the ASF unit. ⋅ C.B.S 3x6,F/ZN Tightening torque:0.8 ± 0.1 N Tightening torque Remove the ASF unit from the main frame upward.

  • Page 55: Disassembly Of Asf Unit

    EPSON Stylus PHOTO RX500/510 Revision C 4.5.5 Disassembly of ASF Unit Several types of spring are used for the ASF unit. Do not loose C A U T I O N springs during disassembly and assembly. Middle Housing Removal. (p43) ASF Unit Removal.

  • Page 56: Power Unit

    EPSON Stylus PHOTO RX500/510 Revision C 4.5.6 Power Unit Middle Housing Removal. (p43) C.B.P Tite 3x8,F/ZN Tightening torque ⋅ ASF Unit Removal. (p54) :0.6 ± 0.1 N Disconnect both power units and the TPU holder assembly lead from the FFC holder on the left side of the printer.

  • Page 57: Front Frame Assembly

    EPSON Stylus PHOTO RX500/510 Revision C 4.5.7 Front Frame Assembly Front Frame Assembly Middle Housing Removal. (p43) C.B.S TITE 3x6, F/ZN Carriage Unit Removal. (p51) ⋅ Tightening torque:0.8 ± 0.1 N Remove 2 screws that secure the Front Frame Assembly.

  • Page 58: Waste Liquid Pad

    EPSON Stylus PHOTO RX500/510 Revision C 4.5.9 Waste Liquid Pad C.B.P TITE 3x8, F/ZN SCREW, FRAME MAIN ⋅ Tightening torque:0.6 ± 0.1 N Tightening torque ⋅ Power Unit Removal. (p56) :0.6 ± 0.1 N Front Paper Guide Removal. (p57) Remove 4 screws that secure the Printer Unit.

  • Page 59: Disassembly And Assembly Of Other Parts

    EPSON Stylus PHOTO RX500/510 Revision C 4.6 Disassembly and Assembly of Other Parts 4.6.1 Damper Assembly Panel Unit Removal. (p41) Remove the Main Board Unit. (p.60) (as needed) Remove a screw that secures the damper assembly, and remove it from the middle housing.

  • Page 60: Main Board Unit

    EPSON Stylus PHOTO RX500/510 Revision C 4.6.3 Main Board Unit C.B.P Tite 3x10,F/ZN C.B.P Tite 3x10,F/ZN ⋅ Tightening torque Tightening torque:0.5 ± 0.1 N If you can read EEPROM on the main circuit board before C H E C K ⋅...
  • Page 61 EPSON Stylus PHOTO RX500/510 Revision C Table 4-4. CN No. Color Pins Connection Point White Power Unit (FFC) CCD Module White TPU Inlet Holder Scanner Motor White HP sensor circuit board (FFC) Panel circuit board CN10 White Detector circuit board...
  • Page 62 C H A P T E R ADJUSTMENT Download Service Manual And Resetter Printer at http://printer1.blogspot.com...

  • Page 63: Overview

    EPSON Stylus PHOTO RX500/510 Revision C 5.1 Overview This Chapter describes the necessary adjustment items and adjustment procedures for applicable Unit / Parts. This section shows details of each Adjustment Process according to Adjustment Program. Adjustment Information for each Printer Mechanism needs to be set for this product in order to maintain reliable printing function and print quality for each printer mechanism.

  • Page 64: Adjustment Items For Individual Units And Components

    EPSON Stylus PHOTO RX500/510 Revision C 5.1.1 Adjustment Items for Individual Units and Components The adjustment items for this product are as indicated below. When performing any of these adjustments, be sure to execute all the related items so that this product operates normally.

  • Page 65: Adjustments By Adjustment Program

    EPSON Stylus PHOTO RX500/510 Revision C 5.2 Adjustments by Adjustment Program Click the [OK] button. While Stylus PHOTO RX500/510 is warming up (Power LED is C H E C K 5.2.1 Overview P O I N T flashing), you cannot run the program (a communication error occurs).

  • Page 66: Adjustment

    EPSON Stylus PHOTO RX500/510 Revision C 5.2.2 Adjustment This section describes the items of the adjustment tabs of the adjustment program. 5.2.2.1 Market Setting (EEPROM initialization) When the Main Board of this machinery has been replaced with a new one, enter the initial setting values in EEPROM with this Adjustment Item.

  • Page 67: Usb Id Input

    EPSON Stylus PHOTO RX500/510 Revision C 5.2.2.2 USB ID Input A specific USB ID is stored in EEPROM on the Main Board. Therefore, it is required to input a USB ID when you have replaced the Main Board with a new one.

  • Page 68: Head Id Input

    EPSON Stylus PHOTO RX500/510 Revision C 5.2.2.3 Head ID Input With this function, write the head ID in EEPROM, and check the current setting value. This adjustment compensates for the uneven discharge of ink to keep the printing quality at a constant level. An irregularity occurs in the printing density unless a proper ID is input.

  • Page 69: 1St Dot Position Adjustment

    EPSON Stylus PHOTO RX500/510 Revision C 5.2.2.5 1st Dot Position Adjustment This adjustment corrects the left margin (Print start position) for post card printing and A4 printing. The value indicated at the center of the adjustment window is the current value recorded in EEPROM.

  • Page 70: Bi-D Adjustment

    EPSON Stylus PHOTO RX500/510 Revision C 5.2.2.6 Bi-D Adjustment This adjustment corrects the deviation of printing timing for bidirectional printing which can occur due to variation of assembly precision/component parts of the Printer Mechanism. Print the Bi-D pattern and make adjustment so that the pattern is printed properly.

  • Page 71: Pw Adjustment

    EPSON Stylus PHOTO RX500/510 Revision C 5.2.2.7 PW Adjustment The PW sensor is installed on the bottom of the Carriage Unit (refer to p.16). Make adjustment so that the program compensates for a dislocation of the Carriage Unit resulting from its removal or replacement, and write the adjustment value in EEPROM.

  • Page 72: Calorific Limitation Input

    EPSON Stylus PHOTO RX500/510 Revision C 5.2.2.8 Calorific Limitation Input Be sure to make this adjustment when you have replaced the C A U T I O N CR Motor or Power Supply Board with a new one. (In the case...

  • Page 73: Maintenance

    EPSON Stylus PHOTO RX500/510 Revision C 5.2.3 Maintenance This section describes the maintenance items of the adjustment program. 5.2.3.1 Head cleaning You can execute more intensive cleaning than Head Cleaning, which is carried out by selecting it in the menu on the Operation Panel. This function releases the Head Nozzle from clogging which can cause dot missing.

  • Page 74: Refurbishment For Doa

    EPSON Stylus PHOTO RX500/510 Revision C 5.2.3.3 Refurbishment For DOA If you clean the cavity of the printhead and cap assembly, this function will be useful. After carry out this function, replace the waste drain ink pad C A U T I O N with new one and reset the Waste drain ink pad counter.

  • Page 75: Eeprom Data Copy

    EPSON Stylus PHOTO RX500/510 Revision C 5.2.3.5 EEPROM data copy The function is to back up → restore (to the new Main Board) the adjustment values that have been stored in EEPROM on the Main Board. Use of this function will reduce the man-hour for adjustment significantly.

  • Page 76: Check Pattern Print

    EPSON Stylus PHOTO RX500/510 Revision C 5.2.4 Check Pattern print This operation prints various adjustment patterns. The patterns for the adjustment items are printed en bloc for each paper type. After printing the adjustment patterns, if any abnormal pattern is...

  • Page 77: Appendix

    EPSON Stylus PHOTO RX500/510 Revision C 5.2.5 Appendix 5.2.5.1 Save all of EEPROM data This function copies all the data in EEPROM into a file. Use this function at the analysis of the product. Figure 5-20. Save All of EEPROM Data Screen...

  • Page 78: Firmware Uploading

    EPSON Stylus PHOTO RX500/510 Revision C 5.3 Firmware Uploading IPL update progress display The following is the status change sequence of normal Firmware update. IPL allows you to update Firmware in the SPC model. Following is the procedure. Table 5-3. IPL Update Progress Display List 5.3.1 Firmware Program File...

  • Page 79: Chapter 6 Maintenance

    C H A P T E R MAINTENANCE Download Service Manual And Resetter Printer at http://printer1.blogspot.com...

  • Page 80: Overview

    EPSON Stylus PHOTO RX500/510 Revision C 6.1 Overview 6.2 Cleaning This section describes maintenance work to maintain the functions and performance of Clean if dirt is visible. As dirt on the glass for placing the document affects directly this product.

  • Page 81: Lubrication

    EPSON Stylus PHOTO RX500/510 Revision C 6.3 Lubrication Cr Shaft 6.3.1 Designated Lubricant Table 6-1. Designated Lubricant Type Name Parts Code Available Grease G-26 1080614 EPSON Grease G-58 1082176 EPSON G-26 6.3.2 Lubrication Points of the Scanner When any part of the CR Unit of the scanner has been replaced or the sound of carriage moving is loud, lubrication is necessary.

  • Page 82: Lubrication Points Of The Printer

    EPSON Stylus PHOTO RX500/510 Revision C 6.3.3 Lubrication Points of the Printer The types and amount of the oils and grease for lubrication of the Printer are determined based on factory evaluation. Therefore, be sure to apply a specified volume of the designated grease to each designated point for repair and maintenance of the Printer.
  • Page 83 EPSON Stylus PHOTO RX500/510 Revision C Main Frame Main Frame Main Frame G-58 Table 6-5. Designated Lubrication Points Assy to be Lubricated Lubrication Points / Precautions (Reference Page) Amount of Application (Fig No.) • Use lubrication jig Lubrication Points G-58 CR guide area of the main frame •...
  • Page 84 EPSON Stylus PHOTO RX500/510 Revision C Carriage Unit Table 6-6. Designated Lubrication Points Assy to be Lubricated Lubrication Points / Precautions <Rear View> (Reference Page) Amount of Application (Fig No.) Lubrication Points Upper contact area of the guide roller and the guide holder...

  • Page 85: Chapter 7 Appendix

    C H A P T E R APPENDIX Download Service Manual And Resetter Printer at http://printer1.blogspot.com...

  • Page 86: Connectors

    EPSON Stylus PHOTO RX500/510 Revision C 7.1 Connectors 7.1.1 Connector Assignments Figure below shows the connector assignments on the circuit boards of Stylus PHOTO RX500/510. Table 7-1. CN No. Color Pins Connected to USB2.0 White Power Unit (FFC) CCD Module...

  • Page 87: Electric Circuit Diagrams

    EPSON Stylus PHOTO RX500/510 Revision C 7.2 Electric Circuit Diagrams This section shows electric circuit diagrams of Stylus PHOTO RX500/510. The electric circuits of Stylus PHOTO RX500/510 are provided on the following circuit boards: C544 MAIN Board C543 Panel Board...
  • Page 88 Model : PM-A850V, Stylus PHOTO RX600/610/RX500/510 Board ; C543 MAIN BOARD Rev. : D Sheet : 1/3 C543 : Mounted C544 : Not mounted...
  • Page 89 C544 : Not mounted C543 : Mounted C544 : Not mounted C543 : Mounted C544 : Mounted C543 : Not mounted C543 : C544PANEL Not mounted C544 : C543PANEL not mounted Model : PM-A850V, Stylus PHOTO RX600/610/RX500/510 Board ; C543 MAIN BOARD Rev.
  • Page 90 Model : PM-A850V, Stylus PHOTO RX600/610/RX500/510 Board ; C543 MAIN BOARD Rev. : E Sheet : 3/3 C544 : Not mounted...
  • Page 91 Model : PM-A850V, Stylus PHOTO RX600/610/RX500/510 Board ; C543 PNL BOARD Rev. : D Sheet : 1/1...
  • Page 92 Model : PM-A850V, Stylus PHOTO RX600/610/RX500/510 Board ; C543 PSB BOARD Rev. : G Sheet : 1/1...
  • Page 93 Model : PM-A850V, Stylus PHOTO RX600/610/RX500/510 Board ; C543 PSE BOARD Rev. : G Sheet : 1/1...

  • Page 94: Exploded Diagrams

    EPSON Stylus PHOTO RX500/510 Revision C 7.3 Exploded Diagrams This section shows exploded diagrams of Stylus PHOTO RX500/510. Appendix Exploded Diagrams...
  • Page 95 For 220V,240V EPSON STYLUS PHOTO RX500/510 NO.1 Rev.01 C544-ACCE-001...
  • Page 96 EPSON STYLUS PHOTO RX500/510 NO.2 Rev.01 C544-CASE-001...
  • Page 97 EPSON STYLUS PHOTO RX500/510 NO.3 Rev.01 C544-ELEC-001...
  • Page 98 EPSON STYLUS PHOTO RX500/510 NO.4 Rev.03 C544-MECH-0012...
  • Page 99 142,143 except for 844 EPSON STYLUS PHOTO RX500/510 NO.5 Rev.01 C544-MECH-002-S...
  • Page 100 EPSON STYLUS PHOTO RX500/510 NO.6 Rev.01 C544-MECH-003...

  • Page 101: Asp List

    EPSON Stylus PHOTO RX500/510 Revision C 7.4 ASP List Table 7-2. ASP List (continued) Ref No. Part Name This section shows the ASP list of Stylus PHOTO RX500/510. STOPPER,CR COVER,MIDDLE,REAR;EPAG Table 7-2. ASP List OPERATION,PANEL;EN COVER,MIDDLE,FRONT;EBM Ref No. Part Name BUTTON,L PAPER,SUPPORT;EDG...
  • Page 102 EPSON Stylus PHOTO RX500/510 Revision C Table 7-2. ASP List (continued) Table 7-2. ASP List (continued) Ref No. Part Name Ref No. Part Name LABEL,TYPE,IC;WST SCALE,CR LABEL,HEAD CLEANING ROLLER,EJECT;C PRINTER MECHANISM(ASP)MAF11-104 BUSHING,6 CARRIAGE ASSY.;B RETAINING RING(B150300711) BOARD ASSY.,DETECTOR,PH BUSHING,6,LEFT COVER,CABLE,HEAD POROUS PAD,CAP,LOWER,LARGE TORSION SPRING,LEVER,CARTRIDGE;B...
  • Page 103 EPSON Stylus PHOTO RX500/510 Revision C Table 7-2. ASP List (continued) Table 7-2. ASP List (continued) Ref No. Part Name Ref No. Part Name COVER,FRAME,PUMP,RIGHT 6N,3,F/ZN ASF UNIT MOTOR C.B.S-TITE(P4),3x6,F/ZN CARRIAGE ASSY.,ASP COMPRESSION SPRING,2.53 SHAFT,CR RETURD ASSY. TIMING BELT C.B.S. SCREW(B300204211) PULLEY,DRIVEN C.B(P)SCREW...

This manual is also suitable for:

Stylus photo rx500

Table of Contents