Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Parweld XTI-160 M
Summary of Contents for Parweld XTI-160 M
- Page 1 XTI-160 M OperatOr Manual ISSue 1...
- Page 2 Thank you and congratulations on choosing Parweld. This Owner’s Manual is designed to help you get the most out of your Parweld products. Please take time to read the Safety precautions. They will help you protect yourself against potential hazards in the workplace. With proper maintenance this equipment should provide years of reliable service.
-
Page 3: Table Of Contents
Contents Page 1.0 Safety precautions 2.0 product description 3.0 Technical Specifications 4.0 Description of controls 5.0 Installation 5.1 Unpacking the Machine 5.2 Location 5.3 Input and grounding connection 5.4 MIG welding torch setup 6.0 Operation 6.1 MIG Welding guide 7.0 Fault finding 8.0 accessories 8.1 Torch spares 9.0 eC declaration of conformity... -
Page 4: Safety Precautions
Insulate work clamp when not connected to work piece to prevent contact with any metal object. Protect yourself and others from flying sparks and hot metal. Be alert that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas. www.parweld.com... -
Page 5: Product Description
Turn face away from valve outlet when opening cylinder valve. Use the right equipment, correct procedures, and sufficient number of persons to lift and move cylinders. www.parweld.com... -
Page 6: Description Of Controls
ON OFF Switch for switching on or off the mains supply to the machine. (mounted on the rear of the machine) note the output of the machine is permanently on in MMa mode unless the on/off switch is in the off position. www.parweld.com... -
Page 7: Unpacking The Machine
The XIT 160M machine should only be used on 230V supply. Refer to the specifications table for voltage tolerances. Your Parweld MIG/MAG Welding Torch has been supplied ready to weld. It has been supplied with the standard consumables denoted Have a qualified electrician connect the input plug. For long runs in the product brochure. -
Page 8: Operation
6” (15cm) away from the power source. There for your application. should be a slight waviness in the exposed wire. If there is no An inexpensive flow meter is available from Parweld reference waviness, the pressure is too low. Tighten the adjustment knob 806001. -
Page 9: Fault Finding
(b) Possible over voltage (b) Check voltage no output, and if necessary (c) Internal fault with the the fan is not move machine to machine operating alternative supply (c) Have a qualified service engineer inspect then repair the welder www.parweld.com... -
Page 10: Accessories
• Designed from brass bar whilst the tube and cover are moulded from high quality polycarbonate to ensure high impact resistance and clarity • Calibrated to operate at an inlet pressure of 30PSI • Sensitive needle valve provides easy adjustment and the downward facing outlet www.parweld.com... - Page 11 18 B1519PL/BK Gun Plug Nut, Plastic c/w Insert ECO1535-40 Everyday Steel Liner .0239-.0309/0.6-0.9mm x 4m 19 Fixed Pin Fixed Pin Assembly 20 ECB1528 Gun Plug Body c/w Fixed Pins 21 B1524 Gun Plug ‘O’ Ring 22 B1525 Liner Nut www.parweld.com...
-
Page 12: Ec Declaration Of Conformity
Steel and steel alloy parts use less than 4% by weight of each homogeneous component. Aluminium and aluminium alloy parts use less than 4% by weight of each homogeneous component. 12 12 Only dispose off in authorised sites for electrical and electronic waste do not dispose of with general refuse or landfill waste. www.parweld.com... -
Page 13: Weee Statement
WEE compliance outside the UK please contact your supplier/Importer Parweld is registered with a compliance scheme Official registration number is WEE/FD0255QV When your equipment reaches the end of its service life you should return it to Parweld where it will be reconditioned or processed for recycling. - Page 14 Parweld Limited Bewdley Business Park Long Bank Bewdley Worcestershire England DY12 2TZ tel. +44 1299 266800 fax. +44 1299 266900 www.parweld.com info@parweld.co.uk...
Need help?
Do you have a question about the XTI-160 M and is the answer not in the manual?
Questions and answers