Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Parweld XTI-201
Summary of Contents for Parweld XTI-201
- Page 1 INSTRUCTION MANUAL...
-
Page 2: Operator Manual
XTI-201 AC/DC OperatOr Manual ISSue 2... - Page 3 Thank you and congratulations on choosing Parweld. This Owner’s Manual is designed to help you get the most out of your Parweld products. Please take time to read the Safety precautions. They will help you protect yourself against potential hazards in the workplace. With proper maintenance this equipment should provide years of reliable service.
-
Page 4: Table Of Contents
Contents Page 1.0 Safety Precautions 2.0 Product description 3.0 Technical Specifications 4.0 Description of controls 5.0 Installation 5.1 Unpacking the Machine 5.2 Location 5.3 Input and grounding connection 5.4 Output Polarity Connections 5.5 Torch Installation 5.6 Work return lead connection 6.0 Operation 6.1 MMA Welding guide 6.2 Basic TIG welding guide... -
Page 5: Safety Precautions
Use protective screens or barriers to protect others Use only well-maintained equipment. Repair or from flash, glare and sparks; warn others not to watch replace damaged parts at once. Maintain unit the arc. according to manual. Wear protective clothing made from durable, flame www.parweld.com... - Page 6 HOT PARTS can cause severe burns. Do not touch hot parts with bare hands. Allow cooling period before working on gun or torch. To handle hot parts, use proper tools and/or wear heavy, insulated welding gloves and clothing to prevent burns. www.parweld.com...
-
Page 7: Product Description
The link between pins 1 and 2 should only be fitted if you are using a remote current control. Wire colours shown refer to the Parweld ERGO TIG torch wiring. 4.0 Description of Controls 1) ON OFF Switch for switching on or off the mains supply to the machine. -
Page 8: Installation
TIG and MMA modes. on the input data label on the unit nameplate. The 13) Positive connection This is used to connect the XTI-201 ACDC machine should only be used on 230V electrode holder in MMA or the earth lead in TIG welding. -
Page 9: Operation
Copper and alloys The most important factor is the high rate of heat conductivity of copper, making preheating of heavy sections necessary to give proper fusion of weld and base metal. www.parweld.com... -
Page 10: Basic Tig Welding Guide
At the end of the weld Zirconiated AC welding of White release the torch trigger and the power will slope aluminium, down and switch off. magnesium and their alloys Guide for selecting filler wire diameter www.parweld.com... - Page 11 10) Set the post gas at around 5 seconds You are now ready to weld. The above settings are a guide and you should adjust to suit the job you are welding if you are unfamiliar with the machine try to www.parweld.com...
-
Page 12: Fault Finding
(f) Wrong build-up sequence remove all slag electrode for from corners position in which (f) Use electrodes welding is done. designed for position in which welding is done, otherwise proper control of slag is difficult. www.parweld.com... - Page 13 Re-position filler pool. TIG welding length in of filler rod guide for ways fillet joint to reduce arc flutter Electrode Electrode is Connect the melts when connected to the electrode to the arc is struck ‘+’ terminal ‘-‘ terminal www.parweld.com...
- Page 14 (c) Internal fault (e) Improve fan is not move machine with the machine connection to operating to alternative work piece supply (c) Have a qualified service engineer inspect then repair the welder www.parweld.com...
- Page 15 To clean the unit, remove the screws securing the outer cover, lift off the outer cover and use a vacuum cleaner to remove any accumulated dirt and dust. The unit should also be wiped clean, if necessary; with solvents that are recommended for cleaning electrical apparatus. www.parweld.com...
-
Page 16: Accessories
WP26AK Tig Spares repair or replacement, at Parweld’s sole option, of any Kit in Plastic Case components or parts of the product determined by Parweld to be defective.
Need help?
Do you have a question about the XTI-201 and is the answer not in the manual?
Questions and answers