Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Parweld XTM353S
Summary of Contents for Parweld XTM353S
- Page 1 XTM353S XTM403S XTM-WF100 OPERATOR MANUAL ISSUE 2...
- Page 2 Thank you and congratulations on choosing Parweld. This Owner’s Manual is designed to help you get the most out of your Parweld products. Please take time to read the Safety precautions. They will help you protect yourself against potential hazards in the workplace. With proper maintanance this equipment should provide years of reliable service.
-
Page 3: Table Of Contents
Contents Page 1.0 Safety Precautions 2.0 Product description 3.0 Technical Specifications 4.0 Description of controls 5.0 Installation 5.1 Unpacking the Machine 5.2 Location 5.3 Input and grounding connection 5.4 Output Polarity Connections 5.5 Changing drive roll sets 5.6 Welding wire installation 5.7 torch installation 5.8 Work return lead connection 5.9 Shielding gas connection... -
Page 4: Safety Precautions
Sparks fly off from the weld. Do not drape cables over your body. If earth grounding of the work piece is required, ground it directly with a separate cable. Do not touch electrode if you are in contact with the www.parweld.com... - Page 5 FLYING METAL can injure eyes. Welding, chipping, wire brushing, and grinding cause sparks and flying metal. As welds cool they can throw off slag. Wear approved safety glasses with side shields even under your welding helmet. www.parweld.com...
-
Page 6: Product Description
The XTM353S and 403S are a separate type machine Turn face away from valve outlet when opening with the wire feed unit connected to the power supply cylinder valve. -
Page 7: Description Of Controls
S No. 60A/ 17V to 350A/ 31.5V 100% PARWELD LTD, 500A 350A BEWDLEY BUSINESS PARK, LONG BANK BEWDLEY, WORCESTERSHIRE, = 42V eff = DY12 2TZ, 1 ~50 Hz GAS INPUT ENGLAND. IP 21S ISO/ IEC 60974-1 Rohs Compliant WIRE FEEDER... -
Page 8: Installation
If the wire feeder is to be used local to the power source. Place the flat chrome disc over the hole in the top of the power source lid . Insert the threaded chrome post thread end first through the flat disc and screw www.parweld.com... -
Page 9: Output Polarity Connections
5.6 Changing drive roll sets 5.8 torch installation Your Parweld MIG/MAG Welding Torch has been supplied ready to weld. It has been supplied with the standard consumables denoted in the product brochure. -
Page 10: Shielding Gas Connection
1/2 turn, run new wire. minimum of 1.2 l/min is recommended. If the only result was drive roll slippage, loosen Parweld recommend the use of its XTS water the Hand nut on the central connector and pull recirculation system designed specifically for use with the gun forward about 6”... -
Page 11: Fault Finding
For supplier). higher amperages and spray transfer the higher inductance setting is preferable. Welding wire extends too far out of nozzle. Be sure welding wire extends not more than 13 mm beyond nozzle. www.parweld.com... - Page 12 – weld metal melting Select lower voltage Increase and/or through base metal and range and reduce wire Resulting in holes where maintain steady travel hanging underneath feed speed. no metal remains. speed. weld. Increase travel speed. www.parweld.com...
- Page 13 Incorrect liner Blocked liner Bird nesting Burn back Bird nesting Excessive feed roll pressure Incorrect or blocked liner Incorrect contact tip size Contact tip overheating Restriction in torch cable Misaligned drive rolls or wire guides Excessive cable kinkage www.parweld.com...
-
Page 14: Accessories
• Fitted with standard 3 /89 BSP inlet and outlet connections Stock Code Description 706101 Flow Meter Mixed Gas 25 lpm (MIG) Gas flow Tester • Designed to check gas flow at the front of Mig Torches. Stock Code Description 806001 Gas flow Tester www.parweld.com www.parweld.com... -
Page 15: Statement Of Warranty
Parweld to be defective. Parweld makes no other warranty, express or implied. This warranty is exclusive and in lieu of all others, including, but not limited to any warranty of merchantability or fitness for any particular purpose.
Need help?
Do you have a question about the XTM353S and is the answer not in the manual?
Questions and answers