Page 2
Thank you and congratulations on choosing Parweld. This Owner’s Manual is designed to help you get the most out of your Parweld products. Please take time to read the Safety precautions. They will help you protect yourself against potential hazards in the workplace. With proper maintenance this equipment should provide years of reliable service.
Accidental contact of electrode to metal objects can cause sparks, parts at once. Maintain unit according to manual. explosion, overheating, or fire. Check and be sure the area is safe Wear a safety harness if working above floor level. before doing any welding. www.parweld.com...
Argon flow regulator Shut off shielding gas supply when not in use. Always ventilate with cylinder pressure gauge and inlet hose, a Parweld MIG torch, confined spaces or use approved air-supplied respirator. and a 3.0m work cable with clamp.
The XTM 182i, Is a compact type machines with integrated wire feed units for use with single phase 230V supply. The machine uses inverter technology to allow MIG , TIG and MMA welding to be performed. Feature XtM182i Input voltage 230V +/-10% 50/60 phases...
Reposition the adjustable pressure arm to its original position to apply pressure. Adjust pressure as necessary. Note the pressure arm should be adjusted in order to give the minimum amount of pressure on the wire to allow reliable feeding, www.parweld.com...
5.7 torch installation Your Parweld MIG/MAG Welding Torch has been supplied ready to weld. It has been supplied with the standard consumables denoted hose delivers cold water directly to the prime source of heat, the in the product brochure. swan neck and consumable. The re circulated water is then passed...
Page 9
0.8 mm 50 - 180 A 1.0 mm 75 - 250 A 1.2 mm WarnInG When using an open arc process, it is necessary to use correct Select Wire Speed (Amperage) eye, head, and body protection. MMA Welding Guide www.parweld.com...
7014 all positional electrode for use on mild and galvanized steel furniture, plates, fences, gates, pipes and tanks etc. Especially suitable for vertical down welding. Cast iron 99% nickel suitable for joining all cast irons except white cast iron www.parweld.com...
Page 11
Wire feed unit operates but no Gas cylinder empty gas flow . Keep arc on leading edge of Gas regulator closed weld puddle. Use correct gun Faulty solenoid angle of 0 to 15 degrees. Restriction in torch cables www.parweld.com...
Page 12
Power source has over heated illuminates leave the machine running to allow it to cool down. Ensure entry and exit vents on machine are clear and machine has a good supply of cooling air. Reduce operating duty cycle and or amperage. www.parweld.com...
Page 13
19 Fixed Pin Fixed Pin Assembly C ECO1535-30 Everyday Steel Liner .0239-.0309/0.6-0.9mm x 3m 20 ECB1528 Gun Plug Body c/w Fixed Pins 21 B1524 Gun Plug ‘O’ Ring ECO1535-40 Everyday Steel Liner .0239-.0309/0.6-0.9mm x 4m 22 B1525 Liner Nut www.parweld.com...
Page 14
Gun Plug Body c/w Spring Pins NI XP2024PC-12-30 Polyamide-Copper Liner .0309-.0459/0.8-1.2mm x 20 XP2023 Gun Plug Body O Ring 10ft3m 21 XP2025 Liner Nipple O Ring XP2024PC-12-40 Polyamide-Copper Liner .0309-.0459/0.8-1.2mm x 22 XP2026 13ft/4m Liner Retaining Nut XP2024PC-12-50 Polyamide-Copper Liner .0309-.0459/0.8-1.2mm x 16ft/5m www.parweld.com...
9 BSP inlet and outlet connections Stock Code Description 706101 Flow Meter Mixed Gas 25 lpm (MIG) Gas flow Tester • Designed to check gas flow at the front of Mig Torches. Stock Code Description 806001 Gas flow Tester www.parweld.com...
9.0 EC declaration of conformity Hereby we declare that the machines as stated below Type: XTM182i Conform to the EC Directives: Low Voltage Directive 2006/95/EC EMC Directive 2004/108/EC Harmonised European standard: EN/IEC 60974-1 This is to certify that the tested sample is in conformity with all provisions of the above detailed EU directives and product standards.
WEE compliance outside the UK please contact your supplier/Importer Parweld is registered with a compliance scheme Official registration number is WEE/FD0255QV When your equipment reaches the end of its service life you should return it to Parweld where it will be reconditioned or processed for recycling.
Page 20
Parweld Limited Bewdley Business Park Long Bank Bewdley Worcestershire England DY12 2TZ tel. +44 1299 266800 fax. +44 1299 266900 www.parweld.com info@parweld.co.uk...
Need help?
Do you have a question about the XTM182i and is the answer not in the manual?
Questions and answers