Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Parweld XTE-171C
Summary of Contents for Parweld XTE-171C
- Page 1 XTE-171C XTE-181C XTE-201C OPERATOR MANUAL ISSUE 1...
- Page 2 Thank you and congratulations on choosing Parweld. This Owner’s Manual is designed to help you get the most out of your Parweld products. Please take time to read the Safety precautions. They will help you protect yourself against potential hazards in the workplace. With proper maintenance this equipment should provide years of reliable service.
-
Page 3: Table Of Contents
Contents Page 1.0 Safety Precautions 2.0 Product description 3.0 Technical Specifications 4.0 Unpacking the Machine 4.1 Fitting Wheels 5.0 Description of controls 6.0 Installation 6.1 Unpacking the Machine 6.2 Location 6.3 Input and grounding connection 6.4 Output Polarity Connections 6.5 Changing drive roll sets 6.6 Welding wire installation 6.7 torch installation 6.8 Work return lead connection... -
Page 4: Safety Precautions
Check and be sure the area is safe before doing any welding. Use only well-maintained equipment. Repair or replace damaged parts at once. Maintain unit according to manual. Wear a safety harness if working above floor level. Keep all panels and covers securely in place. www.parweld.com... -
Page 5: Product Description
Wear approved ear protection if noise level is high. 15%@165A 15%@185A 15%@205A Shielding gas cylinders contain gas under high pressure. Duty Cycle 30%@115A 30%@130A 30%@145A 60%@80A 60%@90A 60%@100A Protection Class IP21S IP21S IP21S Cooling Method Fan Cooling Fan Cooling Fan Cooling www.parweld.com... -
Page 6: Unpacking The Machine
Voltage selector switch. This switch is used to select the required welding voltage. Do Not operate this switch while welding On off switch, switches on the mains power to the machine www.parweld.com... -
Page 7: Installation
I can be adjusted by means of the nut visible when the plastic nut is removed. www.parweld.com... -
Page 8: Torch Installation
Plasma welding torches. the minimum amount of pressure on the wire to allow reliable feeding, The Parweld XTS recirculation equipment can be fitted with a fail- safe flow protection device to prevent overheating or meltdown. 6.7 Torch Installation Note. Water flows into the torch through the blue hose. The blue... -
Page 9: Operation
To stop welding, release the gun trigger and then pull the gun away from the work after the arc goes out. When no more welding is to be done, close valve on gas cylinder (if used), momentarily operate gun trigger to release gas pressure and turn off the machine. www.parweld.com... -
Page 10: Fault Finding
Reduce travel speed. Burn-Through - weld metal Excessive heat input. Select melting lower voltage range and reduce wire feed speed. Completely through base metal Increase and/or maintain Resulting in holes where no steady travel speed. metal remains. www.parweld.com... -
Page 11: Accessories
Restriction in torch cable Flex Cored — — XTEFR0809F Misaligned drive rolls or wire guides Excessive cable kinkage Burn back Improper voltage setting Improper stick out Erratic wire feed Incorrect or blocked liner Contact tip overheating Excessive cable kinking www.parweld.com... -
Page 12: Torch Spares
18 B1519PL/BK Gun Plug Nut, Plastic c/w Insert ECO1535-40 Everyday Steel Liner .0239-.0309/0.6-0.9mm x 4m 19 Fixed Pin Fixed Pin Assembly 20 ECB1528 Gun Plug Body c/w Fixed Pins 21 B1524 Gun Plug ‘O’ Ring 22 B1525 Liner Nut www.parweld.com... - Page 13 20 XP2023 Gun Plug Body O Ring NI XP2024PC-12-30 Polyamide-Copper Liner .0309-.0459/ 0.8-1.2mm x 10ft3m 21 XP2025 Liner Nipple O Ring XP2024PC-12-40 Polyamide-Copper Liner .0309-.0459/ 22 XP2026 Liner Retaining Nut 0.8-1.2mm x 13ft/4m XP2024PC-12-50 Polyamide-Copper Liner .0309-.0459/ 0.8-1.2mm x 16ft/5m www.parweld.com...
-
Page 14: Gas Equipment
Aluminium and aluminium alloy parts use less than 4% by weight of each homogeneous component. Stock Code Description Only dispose off in authorised sites for electrical and electronic 806001 Gas flow Tester waste do not dispose of with general refuse or landfill waste. www.parweld.com... -
Page 15: Weee Statement
WEE compliance outside the UK please contact your supplier/Importer Parweld is registered with a compliance scheme Official registration number is WEE/FD0255QV When your equipment reaches the end of its service life you should return it to Parweld where it will be reconditioned or processed for recycling. - Page 16 Parweld Limited Bewdley Business Park Long Bank Bewdley Worcestershire England DY12 2TZ tel. +44 1299 266800 fax. +44 1299 266900 www.parweld.com info@parweld.co.uk...
Need help?
Do you have a question about the XTE-171C and is the answer not in the manual?
Questions and answers