Table of Contents
Related Manuals for Kichler Lighting Maor 310136
Summary of Contents for Kichler Lighting Maor 310136
- Page 1 65" Maor 310136 A Kichler Decor ceiling fan ® ™ Kichler Lighting ® 7711 East Pleasant Valley Road P.O. Box 318010 Instruction Manual Cleveland, Ohio 44131-8010 Customer Service 866.558.5706 8:30 AM to 5:00 PM EST, Monday - Friday 3066708...
-
Page 2: Safety Rules
1. SAFETY RULES 1. To reduce the risk of electric shock, insure 8. Avoid placing objects in the path of the electricity has been turned off at the circuit blades. breaker or fuse box before beginning. 9. To avoid personal injury or damage to the fan and other items, be cautious when 2. -
Page 3: Tools And Materials Required
65"Maor 2. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver 11 mm wrench Step ladder Wire cutters 3. PACKAGE CONTENTS Unpack your fan and check the contents . You should have the following items: A. Mounting Bracket B. Ball / Downrod Assembly (1) C. -
Page 4: Mounting Options
4. MOUNTING OPTIONS If there isn't an existing ETL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and Outlet box building materials. -
Page 5: Hanging The Fan
65"Maor 5. HANGING THE FAN ETL Listed Outlet Box REMEMBER to turn off the power before you begin installation. This is necessary for your Ceiling Mounting Bracket safety and also the proper programming of the Flat Washer control system. Screw Screw To properly install your ceiling fan, follow the steps below. -
Page 6: Installation Of Safety Support
Step 5. Now lift the motor body into position and place the hanger ball into the hanger bracket. Rotate until the "Check Tab" has dropped into Registration Slot the "Registration Slot " and seats firmly. ( Fig. 9) Check Tab The entire motor body should not rotate is this is done correctly. -
Page 7: Make The Electric Connections
65"Maor 7. MAKE THE ELECTRIC CONNECTIONS SUPPLY CIRCUIT WARNING: To avoid possible electrical shock, Ground be sure you have turned off the power at the Conductor main circuit panel before wiring. Outlet Box Follow the steps below to connect the fan to Green Ground your household wiring. -
Page 8: Attaching The Fan Blades
Step 3. Securely attach and tighten the canopy hole cover over the shoulder screws in the mounting bracket utilizing the keyslot twist-lock Shoulder Screw feature. (Fig. 15) Canopy Hole Cover Fig. 15 9. ATTACHING THE FAN BLADES Blade Arm NOTE: Before continuing , make sure the power Blade Screw is disconnected by turning off the circuit breaker of removing the fuse at the circuit box. -
Page 9: Installing The Switch Housing
65"Maor 10. INSTALLING THE SWITCH HOUSING Step 1. Remove the screw nearest the red dot label on the mounting ring and loosen the other two (do not remove). Let the 9-pin connector from motor Mounting Ring body through the middle hole of switch housing. Align the two slot holes on the switch housing over the 2 screws previously loosened from the mounting ring. - Page 10 12. INSTALLING THE GLASS SHADE AND LIGHT CASE Step 1. Assemble the glass shade to the light kit by twisting in a clockwise direction. Do not overtighten. (Fig. 21) Light Kit Step 2. Let the reverse switch and 2 pull chains Glass Shade through the holes on the light case.
-
Page 11: Troubleshooting
65"Maor 14. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check all electrical connections to insure proper contact. CAUTION: Make sure the main power is OFF when checking any electrical connection. 3. Make sure the transmitter batteries are installed properly. Positive (+) side facing out.
Need help?
Do you have a question about the Maor 310136 and is the answer not in the manual?
Questions and answers