Sony STR-DA5400ES Service Manual page 39

Multi channel av receiver
Hide thumbs Also See for STR-DA5400ES:
Table of Contents

Advertisement

Q Q
3 7 6 3 1 5 1 5 0
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
For Printed Wiring Boards.
Note:
• X : Parts extracted from the component side.
• Y : Parts extracted from the conductor side.
: internal component.
f
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
Parts on the pattern face side seen from
(Conductor Side)
the pattern face are indicated.
Parts face side:
Parts on the parts face side seen from
(Component Side)
the parts face are indicated.
Caution:
Pattern face side:
Parts on the pattern face side seen from
(SIDE B)
the pattern face are indicated.
Parts face side:
Parts on the parts face side seen from
(SIDE A)
the parts face are indicated.
• D VIDEO and DSP boards are multi-layer printed board.
However, the patterns of intermediate-layers have not
been included in this diagrams.
• Indication of transistor.
C
Q
These are omitted.
B
E
Q
T E
L
1 3 9 4 2 2 9 6 5 1 3
B
C E
These are omitted.
∗ Replacement of IC3601 on the D VIDEO board used
in this set requires a special tool.
• Lead layouts
Lead layout of conventional IC
CSP (Chip Size Package)
w w w
STR-DA5400ES
For Schematic Diagrams.
Note:
• All capacitors are in μF unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specifi ed.
: internal component.
f
• 2 : nonfl ammable resistor.
• C : panel designation.
Note:
Note:
The components identi-
Les composants identifi és
fi ed by mark 0 or dotted
par une marque 0 sont
line with mark 0 are criti-
critiques pour la sécurité.
cal for safety.
Ne les remplacer que par
Replace only with part
une piéce portant le nu-
number specifi ed.
méro spécifi é.
• A : B+ Line.
• B : B– Line.
• H : adjustment for repair.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
– A-VIDEO board –
no mark : VIDEO 1 mode
– Other boards –
no mark : TUNER
• Voltages are taken with VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
: AUDIO (ANALOG)
F
: AUDIO (DIGITAL)
J
: VIDEO
E
∗ Replacement of IC3601 on the D VIDEO board used
surface
in this set requires a special tool.
• The voltage and waveform of CSP (chip size package)
cannot be measured, because its lead layout is different
from that of conventional IC.
• Abbreviation
CND : Canadian model
ECE
: Continental European, East European and
Russian models
x
a o
y
.
i
http://www.xiaoyu163.com
8
• Circuit Boards Location
PROTECTOR (SB) board
DCDC2 board
DC-DC board
ACSW board
MIC board
SPSW board
VIDEO 3 board
TEMPERATURE
DETECTION board
Q
Q
3
7
6
3
A CLASS AMP board
CONNECTOR2 board
CONNECTOR1 board
u 1 6 3
.
39
39
2
4
9
9
8
AC board
PROTECTOR (F-C) board
PROTECTOR (SURR) board
DISPLAY board
KEY1 board
MAIN VOL board
1
5
1
5
0
8
9
2
4
SPTM board
TUNER (FM/AM)
POWER AMP board
m
c o
STR-DA5400ES
2
9
9
D CONNECT board
CONTROL board
CIS board
DIGITAL board
DSP board
BIAS board
9
8
2
9
9
DMPORT board
D VIDEO board
A-VIDEO board
ANALOG board
MAIN board
E-VOL board

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents