Sony STR-DA5400ES Service Manual page 145

QQ
3 7 63 1515 0
Pin No. Pin Name
Y24 OCM_INT2
Y25 VGA1_SDA
Y26 VGA1_SCL
AA1
AA2 to
DGND_ADC
AA4
AA23 MSTR0_SDA
AA24 MSTR0_SCL
AA25 VGA0_SDA
AA26 VGA0_SCL
AB1
AB2
AB3 AGND_ADC
AB4 ADC_1.8V
AB23
AB24
AB25 MSTR2_SDA
AB26 MSTR2_SCL
AC1
AC2
AC3 AGND_ADC
AC4, AC5 ADC_1.8V
AC6 AGND_ADC
AC7
AC8 AGND_ADC
AC9 LBADC_3.3V
TE
L 13942296513
AC10 LBADC_IN4
AC11 LBADC_GND
AC12 AVSIN_DATA
AC13 EXTOSD_HS
AC14
AC15 OCMADDR18
AC16
AC17 OCMADDR11
AC18
AC19 OCMADDR4
AC20
AC21 OCMDATA13
AC22
AC23 OCMDATA6
AC24 OCM_CS2N
AC25 OCN_RE_N
AC26 OCN_WE_N
AD1
AD2 AGND_ADC
AD3 to
ADC1_3.3V
AD5
AD6, AD7 ADC2_3.3V
AD8 AGND_ADC
AD9
www
AD10 LBADC_IN3
AD11 LBADC_RETURN
AD12 AVSIN_WORDSEL
.
AD13 EXTOSD_VS
AD14 AVSOUT_DATA
http://www.xiaoyu163.com
I/O
- Not used
- Not used
- Not used
NC - Not used
- Ground terminal
I/O Two-way data bus with the EEPROM
O Serial clock signal output to the EEPROM
- Not used
- Not used
A1P I Component video signal (PR/CR) input from the COMPONENT VIDEO IN jack
SV1P I Analog video signal (R) input from the OSD controller
- Ground terminal
- Power supply terminal (+1.8V)
IO_3.3V - Power supply terminal (+3.3V)
IRO - Not used
- Not used
- Not used
C1P I Component video signal (Y) input from the COMPONENT VIDEO IN jack
B1P I Component video signal (PB/CB) input from the COMPONENT VIDEO IN jack
- Ground terminal
- Power supply terminal (+1.8V)
- Ground terminal
VOUT2 - Not used
- Ground terminal
- Power supply terminal (+3.3V)
- Not used
- Ground terminal
- Not used
- Not used
IO_3.3V - Power supply terminal (+3.3V)
O Address signal output to the fl ash memory
IO_3.3V - Power supply terminal (+3.3V)
O Address signal output to the fl ash memory
IO_3.3V - Power supply terminal (+3.3V)
O Address signal output to the fl ash memory
IO_3.3V - Power supply terminal (+3.3V)
I/O Two-way data bus with the fl ash memory
IO_3.3V - Power supply terminal (+3.3V)
I/O Two-way data bus with the fl ash memory
O Chip select signal output terminal
O Read enable signal output to the fl ash memory
O Write enable signal output to the fl ash memory
AN - Not used
- Ground terminal
- Power supply terminal (+3.3V)
- Power supply terminal (+3.3V)
- Ground terminal
RESET I Reset signal input from the video system controller
- Not used
- Not used
x ao
y
- Not used
i
- Not used
- Not used
http://www.xiaoyu163.com
8
Q Q
3 6 7 1 3
Not used
u163
.
STR-DA5400ES
2 9 9 4 2 8
Description
1 5 0 5 8 2 9 9 4
"L": reset
m
co
9 9
2 8 9 9
145