Sony STR-DN850 Service Manual page 106

STR-DN860/DN1060
Pin No. Pin Name
104 DSP_RESET
105 DSP_CS
106 DSP_MISO
107 DSP_MOSI
108 DSP_SPICLK
109 DSP_INT
110 DIR_INT
111 DIR_CKST
112 DIR_SIGNAL
113 DIR_XMODE
114 AVCC
115 AVSS
116 AVRL
117 AVRH
118 DIR_CSB
119 DIR_SO
120 DIR_SCK
121 DIR_SI
122 DIR_NPCMF
123 NET_HDMI_SEL
FLASH_CLK/PWR_
124
LED
125 SO
126 SI
127 DIR_ERRF
128 DAC_IIC_SDA
129 DAC_IIC_SCL
130 DAC_ZERO_DATA
131 VCC
132 VSS
133 VCC
134 TRSTX (NC)
135 TCK
136 TDI
137 TMS
138 TDO
BT_TX_RATECON_
139
RST
140 TUNER_RDS_SIGNAL
141 TUNER_CE
142 TUNER_MOSI
143 TUNER_CLK
144 MHL_PCONT1
145 MHL1_OVC
146 HDMI_SW_SDA
147 HDMI_SW_SCK
148 RG_RX_INT
149 RG_RX_RESET
150 HDMI_SDA
151 HDMI_SCL
152 RG_SFLASH_SEL
153 RG_FLASH_SPI_SOMI
154 RG_FLASH_SPI_SIMO
155 RG_FLASH_SPI_SCK
156 VCC
157 VSS
106
I/O
O System reset signal output to the DSP "L" reset
O Chip select signal output to DSP
I Serial data input from the serial fl ash and DSP
O Serial data output to the serial fl ash and DSP
O Serial data transfer clock signal output to the serial fl ash and DSP
- Interrupt status signal input from DSP (Not Used)
I Interrupt status signal input from digital audio interface receiver
I Clock selection signal input from the digital audio interface receiver
I Audio serial data input from the digital audio interface receiver
O Reset signal output to the digital audio interface receiver
- A/D converter analog power supply pin
- A/D converter analog ground pin
- A/D converter analog reference voltage input pin
- A/D converter analog reference voltage input pin
O Chip enable signal output to the digital audio interface receiver
O Serial data output to digital audio interface receiver
O Serial clock output to digital audio interface receiver.
I Serial data input from digital audio interface receiver
I SPDIF / IIS NPCM signal input from digital audio interface receiver / HDMI receiver
O Audio selection between NETWORK and HDMI block
I/O Power on/standby/Update LED control port
O Serial data output terminal (use for Firmware Flash Program)
I Serial data input terminal (use for Firmware Flash Program)
I SPDIF / IIS Error signal input from digital audio interface receiver / HDMI receiver
O IIC data output to D/A converter.
O IIC clock output to D/A converter.
I Input signal from DAC when 0 Data
- Power supply pin (+3.3V)
- Ground terminal
- Power supply pin (+3.3V)
O J-TAG test reset input
O J-TAG test clock input
O J-TAG test data input
O J-TAG test mode state input/output
O J-TAG debug data output
O BT TX Rate Converter Reset
I RDS data signal input (for destination that support RDS only)
O Tuner IC enable port.
I/O I2C data output to the tuner
O I2C clock signal output to the tuner
O MHL Power Control
I MHL Over Current Detect
O HDMI Switcher SDA
O HDMI Switcher SCL
I Rogue RX Interrupt
O Rogue Rx Reset
I/O Sparta/HDMI I2C SDA
O Sparta/HDMI I2C SCL
O Rogue SPI Flash Update Select
I Rogue SPI Flash Update Data In
O Rogue SPI Flash Update Data Out
O Rogue SPI Flash Update Clock
- Power supply pin (+3.3V)
- Ground Terminal
Description