Sony STR-DN850 Service Manual page 105

Pin No. Pin Name
51 FL_LAT
52 C
53 VSS
54 VCC
55 EVOL_DATA
56 EVOL_CLK
57 INITX
58 POWER_KEY
59 FL_DATA
60 FL_CLK
61 STANDBY_LED
62 PURE_DIRECT_LED
63 P_CONT3
64 ZONE_SELECT
65 V_SEL_SW2
66 NFC_RFDET
67 NFC_IRQ
68 NFC_SDA
69 NFC_SCL
70 V_COM_MUTE
71 V_SEL_MUTE
72 SL_SR_RY
73 POWER_RY
74 FUSE_DET
75 AC CUT
76 PROTECT
77 BT_TX_MUTE
78 HP_RY
79 BRIDGEABLE_RY
80 SBL_SBR_RY
ZONE2_PREOUT_
81
SW_RY
82 FRONT_SPK_RY
83 C_RY
84 MD1
85 MD0
86 X0 (CLOCK IN)
87 X1
88 VSS
89 VCC
90 INPUT_JOG
91 AD_KEY1
92 AD_KEY2
93 VOLUME_JOG
94 LIMITTER
95 TEMP_SENSOR2
96 TEMP_SENSOR1
97 TEMP_SENSOR3
98 MTK_TEMP_SENSOR
99 NC
100 FS_RATE
JITTER_REMOVER_
101
M0
JITTER_REMOVER_
102
M1
103 DSP_SFLASH_HOLD
I/O
O Latch signal output for FL DISPLAY DRIVER IC
- Power supply stabilization capacity pin
- Ground Terminal
- Power supply pin (+3.3V)
O I2C data output to electrical volume
O I2C clock signal output to the electrical volume
- Micom reset port
I Power switch input terminal
O Serial data output for FL DISPLAY DRIVER IC
O Clock signal output for FL DISPLAY DRIVER IC
O Standby LED
O Pure Direct LED
O Power Control for MTK
I "ZONE SELECT" key input and interrupt
O Composite video output signal switch
I NFC RF Detect Interrupt and Input
I NFC wireless data reception signal
I/O NFC I2C data input/output
O NFC I2C clock signal
O Component Video Mute
O Composite Video Mute
O Relay drive signal (for surround) output terminal "H": relay on
O Relay drive signal (for main power) output terminal "H": relay on
I Fuse open detect signal input
I AC Off detection signal input
I Protect detection signal input terminal
O BT TX Rate Converter Mute
O Relay drive signal (for headphone) output terminal "H": relay on
O Relay drive signal (for power supply) output terminal "H": relay on
O Relay drive signal (for surround back) output terminal "H": relay on
O Relay drive signal (for subwoofer and zone2 preout) output terminal "H": relay on
O Relay drive signal (for front) output terminal "H": relay on
O Relay drive signal (for center) output terminal "H": relay on
- UCOM Mode setting terminal
- UCOM Mode setting terminal
- Clock signal output (4MHz)
- Clock signal output (4MHz)
- Ground terminal
- Power supply pin (+3.3V)
I Function encoder signal input
I Key signal input (A/D port)
I Key signal input (A/D port)
I MASTER VOLUME encoder signal input
I Limiter signal input
I Thermal detection signal input from the thermal sensor
I Thermal detection signal input from the thermal sensor
I Thermal detection signal input from the thermal sensor
I MTK Temperature Sensor (AD)
- Not used
I I2S Fs Rate detect
O NW/DSD Multiplier Select M0
O NW/DSD Multiplier Select M1
O Hold signal output to the serial fl ash
STR-DN860/DN1060
Description
105