Adding Items During A Cycle; Option Selections; Cycle Status Indicators - Kenmore ULTRA WASH 665.17742K010 Use & Care Manual

Adding Items During a Cycle

You can add an item anytime before the main wash starts. Open
the door and check the detergent dispenser. If the cover is still
closed, you can add items.
To add items
1. Open the door slightly to stop the cycle. Wait for the spraying
action to stop before opening the door. The Start/Resume
light will flash.
2. Open the door. If the detergent dispenser cover is still closed,
add the item.
3. Close the door firmly until it latches. The Start/Resume light
will flash.
4. Press START/RESUME.
IMPORTANT: If Lock On is selected, turn off the lock (see Lock
On section in "Option Selections"), or the Start/Resume light will
continue to flash.

Option Selections

You can customize your cycles by repeatedly pressing the
Options button until the desired choices are selected. If you
change your mind, press the Options button again to turn off the
option, or select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
anytime before drying begins.
Press START/RESUME to use the same cycle and option(s) as
the previous wash cycle.
High Temp
Select this option to increase the water temperature during the
wash portions of the cycle. High Temp raises the water
temperature to 145ºF (63ºC), in the main wash. Heating the water
helps improve washing results. High Temp is useful when loads
contain tough food soil.
This option may add heat and wash time to the cycle.
NOTE: High Temp is an option with Heavy Wash and Normal
Wash cycles.
14
Heated Dry
The Heated Dry option in combination with rinse aid will give you
excellent drying results. The energy to use Heated Dry costs
pennies per cycle. Heated Dry is on when the light is lit on the
Heated Dry button. Be sure to load plastic items in the upper rack
to avoid damage.
You may turn off the Heated Dry option by pressing Options so
that the light goes off. However, you will have items in your dish
load that will not be dry at the end of the cycle.
NOTE: The Heated Dry option is used in all cycles except Light
Wash and Quick Rinse. It is an option with the 1 Hr Wash Cycle,
adding ¹⁄₂ hour to the total time.
Lock On
Use the Lock On to avoid unintended use of the dishwasher
between cycles. You can also use the lock feature to avoid
unintended cycle or option changes during a cycle.
When LOCK ON is lit, all buttons are disabled.
NOTE: The dishwasher door can be opened while the controls
are locked. However, the lock must be turned off and the Start/
Resume button pressed to resume the cycle.
To turn on the Lock
Press and hold 4 Hr Delay for 3 seconds. LOCK ON glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
NOTE: If the 4 Hr Delay option is selected, the light will
temporarily turn off until Lock On glows.
To turn off the Lock
Press and hold 4 Hr Delay for 3 seconds. The light turns off.
4 Hr Delay
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay. After adding items, firmly close the door until it latches and
press START/RESUME, or the delay will not continue.
To delay the start
1. Press the 4 Hr Delay button.
2. Select a wash cycle and options.
3. Press START/RESUME.
The dishwasher starts the cycle in the selected number of hours.
NOTES:
To cancel the delay and cycle, press CANCEL/DRAIN.
To cancel the delay and start the cycle, press START/
RESUME.

Cycle Status Indicators

Follow the progress of your dishwasher with the Cycle Status
indicators.
Complete
The Complete light glows when a cycle is finished. The light turns
off when you press any button or close the door.