Table of Contents
Advertisement
g Display indicators panel
The display panel provides four sets of identical
information, for each of the ports which can be used.
The following figure shows one of these displays.
Status indication
E
OVER
E
E
0
20
dB
2
-10
10
-10
1
REC INHI
-20
0
-20
LTC VITC UB
-1
-30
-10
-30
TM1 TM2
-40
-20
-40
-2
REMOTE LOCAL
-60
-40
-60
dB
READY
CH15
Indicators
Time data indication
This shows time data value for the corresponding
port. When you press the MENU button it also shows
setup menu items, and information about Error/
Warning states.
Status indication
This shows the operating status of the port, as follows.
Play................................................................. B
Stopped........................................................... x
Recording ...................................................... z
Variable speed playback (FWD)
at less than 1× speed....................................... B
Variable speed playback (REV)
at less than 1× speed....................................... b
Fast forward or variable speed playback
exceeding 1× speed ........................................ BB
Rewind or variable speed reverse playback
exceeding 1× speed ........................................ bb
Indicators
These show the type of timecode displayed, the
remote/local setting, whether recording is inhibited,
and so forth.
• REC INHIBIT
This appears when recording is inhibited on a
recording port. The recording inhibit setting is
carried out by a setup menu item.
• Time data type
This appears as LTC, VITC, TM1, or TM2,
according to the type of time data currently being
displayed. When user bits from LTC or VITC are
displayed, the UB indicator also appears.
• Remote/local setting
This shows whether the port is set to LOCAL or
REMOTE.
• Port status
When the port is operating normally, the READY
indicator appears.
2-4 (E)
2-1 Front Panel
Time data indication
OVER
E
E
OVER
E
E
OVER
E
0
20
0
20
0
20
dB
2
dB
2
dB
2
10
-10
10
-10
10
1
1
1
0
-20
0
-20
0
-1
-1
-1
-10
-30
-10
-30
-10
-20
-40
-20
-40
-20
-2
-2
-2
-40
-60
-40
-60
-40
dB
dB
dB
CH26
CH37
CH48
Audio level meters
Audio level meters
These show the audio levels for each of the channels
for the currently displayed port (either recording
levels or playback levels as appropriate). When
playing back material recorded with emphasis on, the
"E" indicator appears for the corresponding channel.
Either the FULL mode display (with two possible
range selections) or the FINE mode display is
available. To change the FULL/FINE selection, use
the FULL/FINE button in the display selection
section (c). Setup menu items determine the scale
and headroom settings.
h SET button
Press this button after changing a setup menu item.
i MENU button
Pressing this button lights the indicator, and displays
a setup menu item. Press once again to clear the menu
display without changing the setting.
j REMOTE/LOCAL setting section
REMOTE button: Each time you press this button,
the currently selected port alternates between
REMOTE (Remote mode) and LOCAL (Local
mode). When in Remote mode, the button lights;
when in Local mode, it goes out.
Local mode: The MAV-777 can only be controlled
from the control panel.
Remote mode: The device connected to the
connector panel
s REMOTE IN connector (R1,
'
P1, R2/P3, R3/P2) or the PARALLEL I/O
connector controls the MAV-777.
When the Remote mode is selected, it is necessary to
press the 9P or 50P button to specify the connector of
the external device that controls the MAV-777. When
the external device is connected to the REMOTE IN
connector (R1, P1, R2/P3, R3/P2), press the 9P
button. When the external device is connected to the
PARALLEL I/O connector, press the 50P button. The
button that you press lights.
k PORT SELECT buttons
These select the port used for time data display,
audio/video input source selection, and other settings.
The port selected by these buttons also determines the
port output from MONITOR OUTPUT.
Advertisement
Table of Contents
