CDVI Galeo Installation Manual page 10

INSTALLATION MANUAL
GALEO
Illuminated Weatherproof Keypad with remote electronics
5] PROGRAMMATION
default values
- Without codes.
- Illumination time: 10 seconds.
- Relay release time: 1 second.
- Code length: 5-digit.
- Master Code: 1 2 3 4 5.
- Programming security time :
120 secondes.
- Code length for sub master code:
Version 1 relay (Group 1) =
A and B,
Version 2 relays (Group 2) =
1 and 3
Version 3 relays (Group 3) =
4 and 6.
A. RESET MASTER COdE
ANd USER COdES
1. Enter the master code twice
(1 2 3 4 5 default value master code).
2 beeps are emitted to confirm
entry in programming mode.
2. Press A6 to reset the Master Code
and the User codes.
One beep is emitted. Press on A
and B to confirm reset of all memory
of the keypad. Wait for two beeps.
The master code is restored
to its default value 1 2 3 4 5
and all the User codes are deleted
from the keypad. Once the reset
is completed then the keypad returns
to a stand-by operating mode.
OR
1. Cut the power. Put the jumper on P2.
2. Put the power back.
Wait approximately 3 seconds.
Two beeps are emitted to confirm reset
of the keypad. Remove P2 jumper.
The master code is restored to its default
value 1 2 3 4 5 and all the User codes
are deleted from the keypad.
cdvi.se
10
cdvigroup.com
Audible signal:
The buzzer indicates different
audible signals. It can be turned
off by cutting the ST1 wire on the
remote controller
1 short beep: Keypad powered
1 long beep: data computing in
programming or access granted
2 short beeps: Enter or Exit from
programming
4 short beeps: data computing
error.
Code length
The master code and the User codes
can be of 4 or 5-digit in length.
All the keypad keys can be used to
program a code. The master code and
the Pin code can be of 4 or 5-digit
code. The master code CAN NOT be
used as a PIN code (User Pin code).
The master code CAN NOT be used as
a PIN code (User Pin code). To delete
a specific User pin Code replace it by
0000 if code length is 4-digit format
or replace it by 00000 if the code is in
5-digit format.
P2 jumper:
Reset master code
and user codes
P3 jumper:
modification of individual
code by the user
B. SETTING COdE LENGTH
1. Enter the master code twice.
(1 2 3 4 5 default value master code).
2 beeps are emitted to confirm
entry in programming mode.
2. Press A4 to program the code length.
One beep is emitted. Press 4 or 5
for the digit code. One beep is emitted
to confirm programming of the code length.
3. Press A5 to modify the master code.
One beep is emitted. Enter the new 4
or 5-digit master code. One beep is
emitted to confirm programming
of the new master code.
4. Press B to exit from
programming mode.
2 beeps are emitted to confirm that the key-
pad is in stand-by operating mode.
4 beeps indicate a data computing error.
C. CHANGING THE MASTER COdE
The master code is used only
to enter in programming mode.
1. Enter the master code twice.
(1 2 3 4 5 default value master code).
2 beeps are emitted to confirm
entry in programming mode.
2. Press A5 to modify the master code.
One beep is emitted. Enter the new 4 or 5
digit master code. One beep is emitted
to confirm that the master code is programmed.