GE NetworX NX-4 Installation And Startup page 18

NX-4 Control
LOCATION 18 - CUSTOM COMMUNICATOR FORMAT (See locations 2, 8, & 14)
Segment 1: 1 = On for 1800hz transmit; Off for 1900hz.
2= On for 2300hz handshake; Off for 1400hz.
3= On for cksum parity; Off for double round parity.
4= On for 2 digit event code; Off for 1 digit event code.
5 & 6= Reserved.
7= On for 20 p.p.s.; Off for 10 or 40 p.p.s.
8= On for 10 p.p.s.; Off for 20 or 40 p.p.s.
Segment 2 : 1= On for pager format (no handshake required).
2= On for 1400/2300 handshake.
3 & 4 = Reserved
5= On for Contact ID.
6= On for SIA.
7= On for Contact ID or 4+3.
8= On for DTMF.
Segment 3 & 4: Reserved.
LOCATION 19 - DOWNLOAD ACCESS CODE (8 segments, numerical data)
Location 19 contains the eight-digit access code the NX-4 must receive from the downloading software before the
panel will permit downloading to occur. The factory default code is 84800000.
LOCATION 20 - NUMBER OF RINGS TO ANSWER (1 segment, numerical data)
Location 20 contains the number of rings to answer for a download. Enter a number from A0" (disabled) to "15".
Factory default is "8" and the NX-4 will answer on 8 rings.
LOCATION 21 - DOWNLOAD CONTROL (1 segment, feature selection data)
Location 21 contains the feature selections for the controlling of download sessions. The following features can be
enabled or disabled using this location. (See Feature Definitions starting on page 3)
Segment 1:
1 - On enables two call answering machine defeat.
2 - Reserved.
3 - On requires call back before download session.
4 - Shutdown.
% On locks all local programming.
5 -
% On locks programming of all locations associated with the communicator
6 -
% On locks out download section. (If "On", locations 19 - 22 cannot be viewed from the
7 -
keypad; can only be viewed from the keypad when "Off".)
8 - On enables call back at auto test interval.
%
These selections can only be viewed from the keypad and must be changed through downloading.
LOCATION 22 - DOWNLOAD CALL BACK NUMBER (20 segments, numerical data)
If a telephone number is programmed into this location, and "Require Callback" is enabled in location 21, the control
panel will hang up for approximately 36 seconds (ensuring that the calling party has disconnected), and then call back.
If tone dialing is desired, program an "15" in the segment where tone dialing should begin. If the entire number
should be tone dialing, program an A15" in the first segment. Four-second delays can be obtained anywhere in the
sequence by programming a "13" in the appropriate delay location. WARNING: THE CALLBACK PHONE NUMBER
SHOULD ALWAYS BE REVIEWED FOR ACCURACY BEFORE DISCONNECTING.
LOCATION 23 - FEATURE AND REPORT SELECTIONS (3 segments, feature selection data)
Location 23 is used to enable certain features that can be accessed or are visible to the user from the keypad of the
system. In addition, certain communicator reports are enabled in location 23. This location contains 3 segments of 8
features each. (See Feature Definitions starting on page 3.)
Segment 1: 1 - On enables the Quick Arm feature.
2 - On enables the Re-exit feature.
3 - On enables the Automatic Bypass feature. (Default is "on".)
4 - On enables the Silent Keypad Panic feature (overrides the Audible Panic).
5 - On enables the Audible Keypad Panic feature. (Default is "on".)
6 - On enables the Keypad Aux 1 feature (FIRE).
7 - On enables the Keypad Aux 2 feature (MEDICAL).
8 - On enables the Keypad Multiple Code Attempt Tamper feature.
Page 16