OpenEye CM-511 Installation Manual
Outdoor speed dome camera
Hide thumbs
Also See for CM-511:
- User manual (55 pages) ,
- Quick manual (2 pages) ,
- Quick manual (2 pages)
Related Manuals for OpenEye CM-511
Summary of Contents for OpenEye CM-511
- Page 1 Outdoor Speed Dome Camera Installation Manual Camera Accessories CM-511 CA-510G CA-510PML CA-510W CA-510PMS CA-510C CA-510PA25 CA-510P25 CA-510PA50 CA-510P50 www.openeye.net...
- Page 3 No part of this documentation may be reproduced in any means, electronic or mechanical, for any purpose, except as expressed in the Software License Agreement. OpenEye shall not be liable for technical or editorial errors or omissions contained herein. The information in this document is subject to change without notice.
-
Page 4: Important Safeguards
Important Safeguards Read Instructions Read all of the safety and operating instructions before using the product. Retain Instructions Save these instructions for future reference. Attachments / Accessories Do not use attachments or accessories unless recommended by the appliance manufacturer as they may cause hazards, damage product and void warranty. - Page 5 Installation and Storage Do not install the camera in areas of extreme temperatures in excess of the allowable range. (- 50°C ~50°C / -58°F ~ 122°F) Avoid installing in humid or dusty places. The relative humidity must be below 90%. Avoid installing in places where radiation is present.
- Page 6 Warning DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. Caution C A U T I O N RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
-
Page 7: Standard Warranty
OpenEye will warrant all otherwise out of warranty replacement parts and repairs for 90 days from the date of OpenEye shipment. The above warranty is the sole warranty made by OpenEye and is in lieu of all other warranties by OpenEye express and implied, including without limitation the warranties of merchantability and fitness for a particular purpose. Under... - Page 8 NOTES: viii...
-
Page 9: Table Of Contents
Table of Contents INTRODUCTION ................11 OVERVIEW ..................... 11 GENERAL OPERATION REQUIREMENTS ........... 11 System Configuration .................. 11 GETTING STARTED..............13 CAMERA CONTENTS ..................13 DOME SETUP AND CABLE CONNECTION ..........14 PREPARATIONS for Dome Setup .............. - Page 10 NOTES:...
-
Page 11: Introduction
To extend the network distance up to 1.2 km (4000 feet) and to protect the connected devices, OpenEye recommends placing a repeater at the mid-point. However, a repeater may be needed with network distances less than 1.2 km if the cables used are not CAT 5, 24-gauge cables. Refer to the repeater’s manual for detailed information. - Page 12 NOTES:...
-
Page 13: Getting Started
GETTING STARTED CAMERA CONTENTS Before proceeding, please check that the box contains the items listed here. If any item is missing or has defects, DO NOT install or operate the product and contact your dealer for assistance. All-in-one Data Cable for power Dome Body Screws supply, video and telemetry... -
Page 14: Dome Setup And Cable Connection
DOME SETUP AND CABLE CONNECTION Before installing or connecting the dome camera, please refer to this section and complete preparations for dome setup and all switch settings. PREPARATIONS FOR DOME SETUP The following installation procedure is for the outdoor dome equipped with the sunshield housing. Please follow the steps below to complete dome housing installation. - Page 15 Remove the protective cover and PE sheet. Attach the dome cover to the camera body. Before doing that, apply some lubricant on the cover’s waterproof gasket. This helps keep moisture out of the dome. Note that the tiny protrusion on the cover must align with one of the four holes on the camera body.
- Page 16 DO NOT press the cover as shown in the figure; this may cause damage to the dome camera. Screw the dome cover and body together. Set the switches located on the bottom of the dome camera. Refer to the section on Dome Camera Setup for detailed information about various switch setting.
-
Page 17: Dome Camera Setup
DOME CAMERA SETUP Before connecting the dome camera to other CCTV devices, please complete the camera’s ID and communication switch settings. These switches are located on the bottom of the dome camera. Switch Definition Please refer to the following figure for switch location and definitions. Dome Control Protocol Switch Communication Switch... -
Page 18: Communication Switch Setting
Communication Switch Setting The table below shows the function of each switch within the Communication Switch. Communication Switch RS-485 Setting Termination Line Lock System Initialization Reserved RS-485 is the interface that the dome camera uses RS-485 Setting to communicate with its control device; for this Half-duplex Full -duplex reason, the RS-485 setup of the dome and the... -
Page 19: Dome Control Protocol Setting
Dome Control Protocol Setting Define the protocol you are going to use based on the devices of your surveillance system. Generally, use one protocol even if the devices are provided by different manufacturers. Use the switch to set your dome control protocol and the baud rate. -
Page 20: Dome Cable Definition And Requirements
DOME CABLE DEFINITION AND REQUIREMENTS For operation, the integrated dome camera requires a video cable to carry the video signals to the remote viewing site, a power cable to power the dome and an RS-485 data cable to carry commands from the control device. -
Page 21: 22-Pin Data Cable
The dome camera uses the RS-485 interface to communicate with a connected control device. Connect a control keyboard to the speed dome using the terminal block. OpenEye recommends using CAT 5 cables for RS-485 communication with a maximum length of 4000 feet (1219 meters) for 24-gauge wire. If the total cable length exceeds 4000 feet, use a repeater to maintain the signals. -
Page 22: 22-Pin Connector Definition
22-Pin Connector Definition Using the 22-pin connector, installers can connect the power, video, and RS- 485 cables in one place. The alarm pins are serviceable for connecting alarm input and output devices such as sensors, sirens, or flashing lights to the surveillance system. -
Page 23: Cable Wiring And Connection
Cable Wiring and Connection Users may need to connect cable wiring when: • Connecting self-provided cords to the connector housing instead of using the supplied data cable • Connecting alarm input and output devices. The following table illustrates the proper way to wire cords into the connector housing. 1. -
Page 24: Grounding Recommendation
Grounding Recommendation The GND (ground) wire must be directly connected to the middle pin of the AC24V power connector. Failure to connect the ground can cause damage and failure of the camera and may void the warranty. If the connection of the GND wire causes video noise, use a video isolator. This is only necessary in some situations. -
Page 25: Dome Installation
DOME INSTALLATION OVERVIEW Depending on the user’s installation environment, the dome can be installed on the ceiling, on a wall, or a pole. The following section illustrates installation methods and procedures for installing the dome and mounting accessories. DOME DIMENSIONS The dome dimensions are Ø172 x 302.5mm (6.7 x 11.9 inches) and Ø190 x 302.5mm (7.5 x 11.9 inches) with the sunshield. -
Page 26: Mounting Accessories
MOUNTING ACCESSORIES Wall Mount Bracket (w/ Anti Drop) 184×104×115.2 mm (7.2”×4.1”×4.5”); 0.6 kg (1.2 lbs) Supplied with rubber washer-8×1, pendant tube washer×1, spring washer-8×1 and M8*12 screw×1. Long Wall Mount Bracket (w/ Anti Drop) 348×104×138.6 mm (13.7”×4.1”×5.5”); 1.5 kg (3.3 lbs) Supplied with rubber washer-8×1, pendant tube washer×1, spring washer-8×1 and M8*12 screw×1. - Page 27 Pole Iron, Height: 250/500 mm (9.8/19.7 inches) ,Diameter: 50 mm (2 inches) 1 kg (2.2 lbs) / 1.8 kg (4 lbs) Supplied with rubber washer-8×1, pendant tube washer×1, spring washer-8×1 and M8*12 screw×1. Corner Mounting Plate 222(L)×204(W)×117(D) mm (8.7×8×4.6 inches); 2 kg (4.4 lbs) Supplied with washer-8×4,spring washer×4, M8*16 screw×4, M8 nut×4.
- Page 28 Small Pole Mount 232(L)×136(W)×60(D) mm (9.1×5.4×2.4 inches); Diameter: 112~140 mm (4.4~5.5 inches); 0.7 kg (1.6 lbs). Supplied with stainless steel straps×4, M8*16 screw×4, washer×4. Large Pole Mount 270(L)×170(W)×60(D) mm (10.6×6.7×2.4 inches); Diameter: 112~130 mm (4.4~5 inches); 1 kg (2.2 lbs). Supplied with stainless steel straps×4, M8*16 screw×4, washer×4, spring washer×4...
- Page 29 1 ¼” Threaded Adapter Use to mount the camera to a standard threaded male 1¼” pipe or existing 1¼”male threaded camera mount. All necessary hardware is included. 1 ½” Threaded Adapter Use to mount the camera to a standard threaded male 1 ½” pipe or existing 1 ½” male threaded camera mount. All necessary hardware is included.
-
Page 30: Ceiling Mounting With Pole
CEILING MOUNTING WITH POLE The pole is available in two lengths: 25 cm and 30 cm. Items Needed: • Dome Camera • Ceiling Pole Accessory • Waterproof Gasket (supplied) • Screws and Anchors appropriate for the mounting surface (not supplied) Tools Needed: •... -
Page 31: Wall Mounting With Wall Mount Bracket
WALL MOUNTING WITH WALL MOUNT BRACKET Items Needed: • Dome Camera • Wall Mount Bracket or Long Wall Mount Bracket • Waterproof Gasket (supplied) • Screws and Anchors appropriate for the mounting surface (not supplied) Tools Needed: • Drill • Screwdriver Installation Steps: Cut a cable access hole on the wall. - Page 32 Block the cable entry hole with the supplied sponge. Attach the Wall Mount Bracket to the wall with the appropriate screws and screw anchors (not provided). Attach the Waterproof Gasket to the Wall Mount Bracket. Thread the cables through the top holder and attach the dome to the Wall Mount Bracket with the supplied screws and washers.
-
Page 33: Wall Mounting With Corner Mount
WALL MOUNTING WITH CORNER MOUNT The corner mount must be used in conjunction with the wall mount bracket. Items Needed: Tools Needed: • • Dome Camera Drill • • Wall Mount Bracket Accessory Screwdriver • Corner Mounting Plate • Waterproof Gasket (supplied) •... -
Page 34: Pole Mounting
POLE MOUNTING The dome can be mounted on a pole with the small or large direct mounting accessory and a wall mount bracket. Items Needed: Tools Needed: • • Dome Camera Stainless Steel Strap Cutter • • Wall Mount Bracket Accessory Screwdriver •... -
Page 35: Specifications
SPECIFICATIONS CAMERA SPECIFICATIONS Model CM-511 Outdoor Speed Dome Image Sensor 1/4” EXview CCD Imaging DSP Sony Effio IP Rating IP66 Type / Format NTSC Wide Dynamic Range Minimum Illumination 0.01 Lux (B/W) / 0.1 Lux (Color), 50 IRE @ F1.6... -
Page 36: Ptz Specifications
PTZ SPECIFICATIONS Built-in Protocol Optix III, Pelco D & P, VCL Optical Zoom Pan/Tilt Range 360° Endless / -10° ~ 190° Presets Preset Accuracy ± 0.225° Preset Speed 5° ~ 400°/sec. Pattern Tour (Group) Auto Scan Privacy Mask Zone Title Home Function Preset, Pattern, Tour, Autoscan Auto Flip... - Page 37 All rights reserved. No part of this publication may be reproduced by any means without written permission from OpenEye. The information in this publication is believed to be accurate in all respects. However, OpenEye cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice.