Angelcare AC701 Owner's Manual page 9

TO STOP THE ALARM
OR
Press any key on
the Parent Unit
to put on Hold
(see step 6.5)
Place your
hand back
on the mattress.
TO ADJUST THE SENSOR PAD SENSITIVITY LEVEL:
1
2
Level 1
Level 2
Level 3
3
Level 4
Level 5
TO ACTIVATE THE TIC FUNCTION:
This allows you to hear a 'TIC' sound with baby's movements
(when the movement detection is ON)
1
NOTE:
When the Movement Mode
is set to OFF, the TIC Mode
is automatically set to OFF.
IMPORTANT
• The Sensor Pad is not designed for use with adults, children or infants older
than 24 months.
• Once you are finished using the Sensor Pad, please remove it from the baby's
crib and store it away.
16
OR
Press Nursery
Unit's Hold button
(see step 6.5)
Hold down left 'wing'
button for two seconds
to turn OFF the Unit
1) Press Settings icon to access setting mode.
2) Press Movement Sensitivity icon.
4
The icon will blink.
3) Use the (+) or (-) on the right side of
the Parent Unit to choose the desired
sensitivity level (1 to 5) OR press the
movement sensitivity icon
to choose the desired sensitivity level.
4) Press Return icon to confirm your choice
and return to normal screen.
NOTE:
If you are receiving false alarms,
adjust the sensitivity level.
NOTE:
Whilst in Setting mode, if after 30 seconds
no adjustments are made, the unit will go back
to normal and no update will be done.
1) Press TIC icon to activate
or deactivate the 'TIC' function.
ON OFF
If the TIC icon is activated a regular TIC
sound will emit from Parent Unit.
NOTE:
When using ECO mode, the TIC function
shuts off.
5.2 - SOUND
TO ADJUST THE SOUND:
Press + or - buttons to adjust
the volume level.
NOTE:
At level L0 the level bar will still appear on
the screen and the icon will blink. If you press
the blinking sound icon again, it automatically
activates the Mute function. The Bar will disappear
and a cross will appear in the icon screen.
To DEACTIVATE, press the sound icon again.
(Refer to 6.6 for more information on Mute mode).
TO LOWER VOLUME LEVEL TO L0
Press the
(-) button
to select the
L0 level
(see step 6.6)
TO TEST THE SOUND:
Ask someone to speak into the Nursery
Unit or place the unit near a radio to ensure
that sound is being picked up.
IMPORTANT
To avoid feedback (whistling), keep
both units at least 3 m apart.
5.3 - BATTERIES
HOW TO CHECK THE BATTERIES:
Unplug the AC Adapters from both units.
• If the green light on the Nursery Unit does not show, replace the batteries.
• If the Parent Unit and its screen do not light up, recharge the batteries.
HOW TO CHARGE THE BATTERIES IN THE PARENT UNIT:
Leave the Parent Unit in the Charging Cradle
to fully charge the unit. Although the batteries
at 1/3 capacity works normally, we recommend
that you fully recharge them.
PARENT UNIT BATTERY ALARM
• Alarm activates when batteries need to be recharged.
• Parent Unit will emit a beep sound every 20 seconds.
• Battery icon will flash on Parent Unit screen.
Level 0
Level 1
Raise volume
level (+)
Level 2
Lower volume
level (-)
Level 3
Level 4
Level 5
PUT IN TALK BACK MODE
Press and hold
the Talk Back
button to speak
to your baby.
IF YOU HEAR NO SOUND:
• Check that both units are switched on.
• Check that both units are plugged
into a working electrical outlet.
• Check the batteries in both units
(replace or recharge them as necessary
per unit).
• Bring the Parent Unit closer to the
Nursery Unit.
1/3 full 2/3 full full
17