Microh HALO BEAM 150 User Manual

Microh HALO BEAM 150 User Manual

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HALO BEAM 150 and is the answer not in the manual?

Questions and answers

Summary of Contents for Microh HALO BEAM 150

  • Page 2 Congratulations on purchasing this 120W moving Beam Light Thank you for extending your trust in our technology Voltage :110V/240V AC, 50/60Hz Power Consumption:150W Lamp:2R 120w (DMX on/off) Lumen output:70000LM/10meter Color Temperature:8000K Lens:3-layer optic glass lens Prism:8 Prism rotation Gobo:Gobo wheel with 14 gobos Colors:Color wheel with 13 colors,single rotation rainbow effect DMX Channel:13CH Control:Master-slave mode...
  • Page 3 suitably qualified; -Verify whether any visible damage was caused during transport.lf the power cord.housing or the light are damaged,do not operate the device;contact your specialized dealer immediately. 2. Supply Voltage,Mains Cord and Connection to Mains The handling of supply voltage,mains cords and connections to mains calls for particular care considering the risk from a life-threatening electric shock,the risk of fire and the risk of short circuits please observe the following notes in particular: Products operating on supply voltage should be kept out of the reach of children.Therefore ensure the permanent...
  • Page 4 value for relative humidity is 50% at 45 saturation in the room must not reduce the visibility to below 10m . The product must be operated at a temperature range of between -5 and 45 only.Protect the product against direct exposure to sunlight or other heat,such as from radiators! If the product is taken from a cold environment into a warm environment it must only be taken into operation once it has reached ambient temperature,since the condensation created by the difference in temperature may destroy the device! Protect the product against dust!Dust may reduce the protective insulation,which may cause fatal electric shocks!
  • Page 5 device with the input of the second device and the output of the second device with the input of the third device and so on. Connect the mains plug to an outlet. Operating the product for the first time may generate smoke and odour,this is not a defect.Avoid dis/connecting the product repeatedly and quickly from/with mains!Always wait 15 minutes prior to the next dis/connection! The device starts not until a self-testing and starting time.If the moving head is ready to start,push and roll the function wheel.The LCD display shows the options,as below:...
  • Page 6: Dmx Chart

    Dmx Address A001~AXXX Lamp Control ON/OFF Lamp power ON/OFF No signal Close//Hold /Sound Mode /Auto System Setting Pan Reverse ON/OFF Tilt Reverse ON/OFF Microphone level ON/OFF Factory Setting Current Hours XXXX(Hours) Life Hours XXXX(Hours) Last Run Hours XXXX(Hours) Information Timer Password Password=XXX Clear Time ON/OFF...
  • Page 7 30-34 GREEN 35-39 GREEN – LIGHT YELLOW 40-44 LIGHT YELLOW 45-49 LIGHT YELLOW - PINK 50-54 PINK 55-59 PINK - YELLOW 60-64 YELLOW 2 65-69 YELLOW - MAGENTIA 70-74 MAGENTIA - BLUE 75-79 BLUE 80-84 BLUE – CCT 3200K 85-89 CCT 3200K 90-94 CCT 3200K –...
  • Page 8 190-196 Rot. gobo 11 shake 197-203 Rot. gobo 12 shake 204-210 Rot. gobo 13 shake 211-217 Rot. gobo 14 shake 218-255 Fixed gobo wheel cont. rotation slow to fast Rotating prism, Prism / Gobo macros: 0-127 Open 128-255 8 facet prism Rotating prism: No rotation 8-127...

Table of Contents