Related Manuals for MGE UPS Systems 2200 RT 2U
Summary of Contents for MGE UPS Systems 2200 RT 2U
- Page 1 Pulsar M 2200 RT 2U 2200 RT 3U 3000 RT 2U 3000 RT 3U 3000 RT 3U XL EXB RT 3U Installation and user manual - Page 1 34003641FR/AA...
- Page 2 - Page 2 34007776EN/AB...
- Page 3 Before installing Pulsar M, please read the booklet on the required safety instructions. Then follow the indications in this manual. To discover the entire range of MGE UPS SYSTEMS products and the options available for the Pulsar M range, we invite you to visit our web site at www.mgeups.com or contact your MGE UPS SYSTEMS representative.
- Page 4 Introduction Pictograms Important instructions that must always be followed. Information, advice, help. Visual indication. Action. Audio signal. In the illustrations on the following pages, the symbols below are used: LED off LED on LED flashing - Page 4 34007776EN/AB...
-
Page 5: Table Of Contents
Presentation Standard positions ... 6 Tower position ... 6 Rack position ... 6 Rear panels... 7 Pulsar M 2200 / 3000... 7 Pulsar M EXB (optional battery module)... 7 Control panel... 7 Installation Unpacking and contents check ... 8 Installation in tower position ... 9 Installation in rack position ... -
Page 6: Presentation
Tower position Rack position - Page 6 34007776EN/AB Dimensions (H x W x D) in mm Pulsar M 2200 RT 2U 440 x 86 x 640 Pulsar M 2200 RT 3U 440 x 131 x 490 Pulsar M 3000 RT 2U... -
Page 7: Rear Panels
1.2 Rear panels Pulsar M 2200 / 3000 Pulsar M EXB (optional battery module) 1.3 Control panel 1. Presentation (1) USB communication port (2) RS232 communication port (3) Connector for automatic recognition of an additional battery module (4) Slot for optional communication card (5) Connector for remote ON/OFF and RPO (Remote Power Off) control (6) Connector for additional battery module... -
Page 8: Installation
2. Installation 2.1 Unpacking and contents check (30) Pulsar M 2200 or 3000 UPS (31) connection cable to AC-power source (32) 2 connection cables for the protected equipment (33) RS232 communications cable (34) USB communications cable (35) 2 systems to secure power plugs (36) Solution-Pac CD-ROM (37) Documentation Packing materials must be disposed of in compliance with all local regulations concerning waste. -
Page 9: Installation In Tower Position
It is advised to first install the battery module, then the power module above. Follow steps 1 to 4 for module mounting on the rails. The rails and necessary hardware are supplied by MGE UPS SYSTEMS. 2. Installation - Page 9... -
Page 10: Communication Ports
2. Installation 2.4 Communication ports Connection of RS232 or USB communication port (optional) The RS232 and USB communication ports cannot operate simultaneously. Installation of the communication cards (optional) - Page 10 34007776EN/AB 1 - Connect the RS232 (33) or USB (34) communication cable to the serial or USB port on the computer equipment. -
Page 11: Connection With A Flexpdu (Power Distribution Unit) Module
2.5 Connections with a FlexPDU (Power Distribution Unit) module (optional) 2.6 Connections with a HotSwap MBP module (optional) The HotSwap MBP module makes it possible to service or even replace the UPS without affecting the connected loads (HotSwap function). 2. Installation 1 - Connect the UPS socket (10) to the AC- power source using the cable (31) supplied. -
Page 12: Hotswap Mbp-Module Operation
2. Installation HotSwap MBP-module operation UPS start-up with the HotSwap MBP module 1 - Check that the UPS is correctly connected to the HotSwap MBP module. 2 - Set switch (53) to the Normal position. 3 - Start the UPS by pressing the ON/OFF button (27) on the UPS control panel. The load is supplied by the UPS. -
Page 13: Operation
If UPS personalisation is desired, it is advised to enter the personalisation mode at this time. This mode may be entered using the buttons on the control panel or the Personal Solution-Pac software (Windows) included on the Solution-Pac CD-ROM provided by MGE UPS SYSTEMS. 3.2 Operation on battery power... -
Page 14: Return Of Ac Power
Pulsar has the choice of two remote control options. ◗ RPO: Remote Power Off allows a remote contact to be used to disconnect all the equipment connected to the UPS from the power supply. Restarting the UPS requires manual intervention. ◗... - Page 15 Contact open: shut down of UPS Contact closed: start-up of UPS (UPS connected to the network and network energized) Note: local On/Off control via button (27) has priority over the remote control order. Contact open: shut down of UPS To return to normal operation, deactivate the external remote shut down contact and restart the UPS using button (27).
-
Page 16: Access To Measurements And Personalisation Data
4. Access to measurements and personalisation data 4.1 Display menus arrangement 4.2 Access to measurements Press the scroll button (25) to access any status conditions and alarms, then the measurements for voltage, current, frequency, power output and battery backup time. 4.3 Personalisation using the control panel Local personalisation Function... -
Page 17: Personalisation Using External Software
4. Access to measurements and personalisation data Output personalisation Function Output voltage Frequency converter Output frequency Transfer to the bypass AC input Overload level (1) These parameters may be modified only when the UPS is OFF. Detailed comments are available in the Personal Solution-Pac software. ON/OFF personalisation Function Start on battery power... -
Page 18: Maintenance
5. Maintenance 5.1 Troubleshooting If LED (21) or (22) is ON, a fault or an alarm has occurred. Use the escape button (24) to stop the audio alarm. Indication The UPS does not start, the alphanumeric display indicates: COLD START NOK CHECK AC WIRING LED (22) is ON, the SWF LED (11) at the rear of the UPS is ON. -
Page 19: Troubleshooting A Ups Equipped With The Hotswap Mbp Module
Troubleshooting a UPS equipped with the HotSwap MBP module Indication The load is no longer supplied when the rotary switch (49) on the HotSwap MBP module is set to the Bypass position. The load is no longer supplied when the rotary switch (49) on the HotSwap MBP module is set to the Normal position. -
Page 20: Mounting The New Battery Module
Mounting the new battery module Carry out the above instructions in reverse order. ◗ To ensure safety and high performance, use only batteries supplied by MGE UPS SYSTEMS. ◗ Take care to firmly press together the two parts of the connector during remounting. -
Page 21: Training Centre
5.4 Training centre To fully master operation of your MGE UPS SYSTEMS product and carry out level 1 servicing, see our complete range of technical training courses, available in both French and English. 50 Hz training centre 60 Hz training centre... -
Page 22: Appendices
6. Appendices 6.1 Technical specifications Output power Electrical supply network ◗ Rated input voltage ◗ Input voltage range ◗ Frequency ◗ Power factor ◗ Leakage current Load output ◗ Voltage ◗ Frequency ◗ Harmonic distortion ◗ Overload capacity ◗ Current Battery Environment ◗... -
Page 23: Glossary
6.2 Glossary Bypass AC input Backup time Battery test Equipments Excessive discharge FlexPDU Frequency converter HotSwap MBP Low-battery warning Normal AC input Percent load Personalisation Programmable outlets Start on battery power UPS ON/OFF controlled by software Bypass line from the AC-power source, controlled by the UPS, used to directly supply the load if an overload or a malfunction occurs on the UPS. - Page 24 MGE UPS SYSTEMS T H E U N I N T E R R U P T I B L E P O W E R P R O V I D E R 140, Avenue Jean Kuntzmann ZIRST - Montbonnot St Martin 38334 - Saint Ismier Cedex - France www.mgeups.com...