Copy Of Lighting Plate Instructions; Normal Operating Sounds Of Gas Appliances; Resetting The Unit - Regency Fireplace Products GFI300LNG-R Owners & Installation Manual

OPERATING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
with local codes, if any; if not,
follow the current CAN1-B149/ANSI Z 223.1
(Australia: AS5601-2004, New Zealand: NZS
5261/ NZS5266)
WARNING: If you do not follow these
may result causing property damage,
personal injury or loss of life. Improper
installation, adjustment, alteration, service
or maintenance can cause injury or property
manual provided with this appliance. For
assistance or additional information consult
supplier.
A) BEFORE LIGHTING smell all around the appliance
some gas is heavier than air and will settle on the
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance
- Do not touch any electric switch, do not use
- Immediately call your gas supplier from a
instructions.
department.
to inspect the appliance and to replace any part of
the control system and any gas control which has
This appliance needs fresh air for safe operation and
CAUTION: Hot while in operation. Do not
touch. Severe Burns may result. Due to
high surface temperatures keep children,
clothing and furniture, gasoline and other
See installation and operating instructions
accompanying appliance.
LIGHTING INSTRUCTIONS
STOP!
1) Plug the power cord into a power outlet.
2) Press and release the ON/OFF button once to
start the unit.
*
ON/OFF function may be controlled by either
Remote Wall Mount Control or ON/OFF control
on the Unit.
3) After approximately 3 seconds the spark
ignition system will spark for 25 seconds to
light the main burner.
4) If the main burner does not light, check the
gas and reset the unit.
TO TURN OFF GAS APPLIANCE
1) Press the ON/OFF button once.
2) Turn off all electric power to the unit if service
is to be performed.
DO NOT REMOVE THIS
INSTRUCTION PLATE
24 24

COPY OF LIGHTING PLATE INSTRUCTIONS

NORMAL OPERATING
SOUNDS OF
GAS APPLIANCES
It is possible that you will hear some sounds from
your gas appliance. This is perfectly normal due to
the fact that there are various gauges and types
of steel used within your appliance. Listed below
are some examples. All are normal operating
sounds and should not be considered as defects
in your appliance.
Blower:
Regency gas appliances use high tech blowers
to push heated air farther into the room. It is not
unusual for the fan to make a "whirring" sound
when ON. This sound will increase or decrease
in volume depending on the speed setting of your
fan speed control.
Burner Tray:
The burner tray is positioned directly under the
burner tube(s) and logs and is made of a different
gauge material from the rest of the fi rebox and
body. Therefore, the varying thicknesses of steel
will expand and contract at slightly different rates
which can cause "ticking" and "cracking" sounds.
You should also be aware that as there are tempera-
ture changes within the unit these sounds will likely
re-occur. Again, this is normal for steel fi reboxes.
Gas Control Valve:
As the gas control valve turns ON and OFF, a
dull clicking sound may be audible, this is normal
operation of a gas regulator or valve.
Unit Body/Firebox:
Different types and thicknesses of steel will expand
and contract at different rates resulting in some
"cracking" and "ticking" sounds will be heard
throughout the cycling process.
919-130
WARNING:
DO NOT SPRAY AEROSOLS IN THE VICINITY OF
THIS APPLIANCE WHILE IN OPERATION.
Appliances incorporating a live fuel effect (designed to oper-
"
ate with blue fl ames with slight yellow tips) may exhibit slight
carbon deposition."

RESETTING THE UNIT

If the appliance goes to 'lockout', the system
will have to be reset by depressing the reset
button - located on the right side of the unit
by glass frame.
*Important: Wait at least 5 min for any un-
burned gas to clear before resetting the
appliance.
1) "Turn unit "on" via remote or touch pad.
2) Locate the reset button on the bottom right
side of the fascia.
3) Press and release the reset button - once.
4) Wait for approximately 3 seconds - the
pilot sparks can be heard and seen. It will
take approximately 2 to 3 seconds for the
fl ame to be lit.
NOTE: Wait 5 minutes between reset
attempts.
NOTE: If unit fails to light after 25 seconds;
wait 5 min, then manually reset using
red button on the right hand side below
glass frame.
Regency GFI300L Gas Fireplace Inbuilt