Safety Precautions Explanation of Graphical Symbols This symbol indicates the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. This symbol indicates the presence of uninsulated ”dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Page 3
These precautions must be followed for safety reasons. Warning Do not use if the unit emits smoke, strange sounds are heard or odor is emitted. Continued use may cause electrocution and/or fire. Immediately remove the power plug from the outlet. Once the unit stops emitting smoke, consult the dealership where this unit was purchased or factory shop for repairs.
Page 4
and/or electrocution. Do not place a container holding water or other liquids above the unit when it is connected to power. In the event that water gets inside the unit, turn off and unplug the unit. Consult the dealership where this unit was purchased or factory shop. Continued use may result in a fire or electrocution.
Page 5
Connect and install the power cable and connection cable very carefully. Tripping over the cable may result in the unit capsizing or falling and cause injury. Do not place heavy objects on connected units. Doing so may affect the stability of the unit and cause it to fall which may result in injury. Doing so may also damage the unit depending on the weight of the object.
Page 6
Do not use this unit if condensation has formed. Using this unit while condensation is formed may cause breakdowns. In the event of sudden sharp temperature changes, turn off the power and do not use this unit until the temperature of the room where it is positioned stabilizes (about 2 hours).
Product Components The package contains the main unit and its components as specified below. When you purchase the unit, Please check to ensure the components specified below are included. DVR Set Client Software CD, User Guide Remote Control , Battery1.5V, Mouse HDD SATA data cable HDD mounting bracket &...
Mounting the HARD DISK 1. Remove the unit’s cover. 2. Fix the supplied rubber pads to the supplied HDD mounting bracket. Then fix the hard disk to the mounting bracket using the supplied screws (A). 3. Connect the unit’s power cable (B) and the supplied S-ATA cable (C) to the hard disk.
Booting the DVR and Basic Time Setting 1. During the first start up, the following message will be displayed. Setting Daylight Saving Time If the DVR is to be set Day Light Saving Time and be synchronized NTP (Network Time Protocol), Take next steps. 1.
Page 12
Setting NTP (Network Time Protocol) 1. When the DVR is connected with internet and the DVR need to be syncronized with NTP (Network Time Protocol), set SETUP>SYSTEM>NTP ON. 2. Select proper TIME ZONE time. NOTE: If you want the unit to automatically synchronize the local time, the Time Zone must be properly set according to your local Time Zone.
Table of Contents Name, Function and Connection ......................18 1-1. Front Panel ........................... 18 1-2. Rear Panel ........................... 20 1-3. Remote control ..........................21 Setting up the DVR ..........................21 2-1. Setup – Main Screen ........................21 2-2. Setup – Display Mode ........................25 2-3.
Page 16
6. Back up ..............................57 6-1. Still Image backup onto USB flash memory .................. 57 6-2. Video backup onto USB flash memory ..................57 6-3. Transferring still images or video from the ARCHIVE list .............. 58 6-4. Playback of Backup Video ......................59 7.
Page 17
How to access DVR from Remote PC? ..................105 C. How to access DVR with iPhone? ....................108 D. How to access DVR with Android? ....................110...
1. Name, Function and Connection 1-1. Front Panel The following information will help you to operate the front panel controls. Figure 2.1.1. Front panel Indication Lights Name Description Indication light is on when power is applied to the system. POWER Green –...
Page 19
Set the alarm output mode. (On or Off) Press to go to SEARCH menu in live display mode. Press to play/pause the footage in playback mode. Press to enter SETUP menu. Enable/disable automatic sequence display channels in full screen, quad, 9-split display mode. Press to control Pan/Tilt/Zoom operations.
1-2. Rear Panel Figure 2.2.1. Rear Panel Table 2.2.1. Rear panel connections Connection Purpose VIDEO IN connectors for video input. HD-SDI AUDIO IN 4/8/16 connectors for audio input. In case of 16ch, an audio cable is needed from ch 5 to ch 16. AUDIO OUT 1 connector for audio output.
1-3. Remote control ① ID: When a remote control ID number is set in DVR, press it before number. ② REC: To start and stop manual recording. ③ Number: To select channel (1, 2, 3, & 4) or to enter DVR ID number. ④...
Page 22
button on the front panel. Then select a user type. User can select one of user types (ADMIN, USER1, ◀ ▲ ▶ ▼ USER2, USER3) using the control button ( ) on the front panel and press SEL button. Input the password by front key panel, mouse or remote controller. Use the Virtual Keyboard when you use front key and mouse.
Page 23
SYSTEM INFORMATION: Display a software version, storage size, network type, IP address, MAC address, DDNS status, DVR ID and remote controller ID of the system. SYSTEM LOCK: To lock the system, user input a password. To unlock the system, please press ESC button for 5 seconds on a front panel or a remote control.
Page 24
– RECORDING LIMIT RECORDING LIMIT DAYS – S.M.A.R.T SYSTEM – DVR-ID – DESCRIPTION – LANGUAGE – DATE FORMAT – SET DATE & TIME – CLIENT ACCESS – – SEND EMAIL SECURITY – USER AUTHENTICATION – USER PASSOWRD – AUTHORITY OF PLAYBACK NETWORK –...
2-2. Setup – Display Mode Press the SETUP button and enter the password. The setup menu is displayed as picture below. Select DISPLAY icon and press SEL button to enter the setup menu item. Navigate through the menu items using ◀...
OUTPUT 60Hz, 1080p 50Hz, 1080p 60Hz). Default value is 720p 60Hz. If the monitor doesn’t (HDMI/VGA) support some output type, it would be returned to the previous value. 2-3. Setup – Recording Mode Press the SETUP button and enter the password. The setup menu is displayed as picture below. Select RECORD icon and press SEL button to enter the setup menu item.
Page 27
RESOLUTIO Set the resolution for the specified channel: 1920x1080, 1920x540, 1280x720 and 640x360. You can see the 1920x1080 and 1920x540 menu when 2M HD-SDI camera is connected. FRAME Set the frame rate for the specified channel. The sum of the frame rate values from each RATE channel cannot exceed the maximum frame rates for a specific recording resolution.
2-3-1. Recording Schedules To setup a recording schedule, select SCHEDULE in the RECORD menu. Navigate through the items using ◀ ▲ ▶ ▼ the control button ( Once the channel 1 is selected, SCHEDULE-CH1 screen is displayed. Select ALL or each day using the ◀...
C: CONTINUOUS recording, when you select the color will change to Blue Color M: MOTION recording, when you select the color will change to Yellow Color S: SENSOR recording, when you select the color will change to Red Color -: Does not record [ALL]: Move the cursor to ALL and select a recording mode C,M or S using the SEL button to set the same setting for every day.
Table 2.4.1. Menu items in Device Setup screen Item Description ALARM OUT Set the sensor, motion, and video loss for each alarm. CONTROLLER & PTZ Set the Controller and PTZ camera speed, number, type and CHANNEL Select specified channel for motion zone setup. MOTION ZONE Select either Full Zone or Partial Zone for motion sensing.
Table 2.4.2. Menu item in ALARM-OUT Setup screen Item Description ALARM OUT Select an alarm out number. Available NO: 4ch (1) SENSOR IN Enable Alarm Out by Sensor up to 4 Inputs. MOTION ON Enable Alarm Out by Camera Motion up to 4 cameras. VIDEO LOSS ON Enable Alarm Out by Video Loss up to 4 cameras.
2-4-3. Motion Zone Setup ◀ ▲ ▶ ▼ Select MOTION ZONE using the control button ( ) and select either PARTIAL ZONE or FULL ◀ ▲ ▶ ▼ ZONE using the control button ( ). And press the SEL button. If FULL ZONE is selected, the motion setting screen is not displayed.
Page 34
Figure 2.5.1. STORAGE setup screen Table 2.5.1. Menu items in STORAGE Setup screen Item Description OVERWRITE When enabled, the DVR will continue recording and overwrite the oldest existing recorded data once the hard drive is full. When disabled, recording will stop once the hard drive is full.
Page 35
DISK INFO Hard drive information RECORDING Enable/disable recording limit. LIMIT RECORDING Set the recording limit days.(1- 90 days) LIMIT DAYS The data will remove by the hour. S.M.A.R.T. Set the alarm and buzzer by setting HDD temperature limit.
2-6. Setup – System Mode Press the SETUP button and enter the password. The setup menu is displayed as picture below. Select SYSTEM icon and press SEL button to enter the menu item. Navigate through the menu items using the ◀...
Page 37
◀ ▲ ▶ ▼ LANGUAGE Select the display language using the control button ( ). Once a language is selected, the display language changes. ◀ ▲ ▶ ▼ DATE Select the date display format using the control button ( ). Options are: FORMAT YYYY/MM/DD, MM/DD/YYYY, DD/MM/YYYY, YYYY-MM-DD, MM-DD-YYYY, DD-MM- YYYY...
Page 38
◀ ▲ ▶ ▼ Select BEGIN or END using the control button ( ) and press the SEL button. ◀ ▲ ▶ ▼ Select the item using the control button ( ), select the setting ◀ ▲ ▶ ▼ value using the control button ( ) and press the ESC button to return to SET DATE &...
Page 39
TRANSMISSION MODE: Sending an image only of the channel that triggered the alarm when an alarm event is triggered. IP NOTIFICATION: Enable/disable sending e-mail when the IP address of your DVR is changed. EVENT ALARM: Enable/disable sending e-mail reports on the channel that triggered the alarm when an alarm event is triggered.
2-7. Setup – SECURITY Mode Press the SETUP button and enter the password. The setup menu is displayed as picture below. Select SECURITY icon and press SEL button to enter the setup menu item. Navigate through the menu items ◀ ▲ ▶ ▼ ◀...
confirm and select OK. Then the message “PASSWORD CHANGED” is displayed. The factory default password is 1111. AUTHORITY OF Enable/disable a covert function in playback mode. PLAYBACK V: No covert. Blank: Covert 2-8. Setup – Network Mode Press the SETUP button and enter the password. The setup menu is displayed as picture below. Select NETWORK icon and press SEL button to enter the setup menu item.
Page 42
Figure 2.8.1. NETWORK setup screen Table 2.8.1. Menu items in Network Setup screen Item Description PORT Port number (Default: 5445) WEB PORT Web Sever Port number (Default: 80) NETWORK TYPE Select a type of network connection. Options are: DHCP and STATIC Note.
2-8-1. Port and Web Port When you connect one or more DVRs to a network through an IP sharing device, each device must have a unique TCP port number for access to each unit from outside the LAN. Also, the IP sharing device must be configured for port forwarding so when each port is accessed on the IP sharing device, it will forward to the appropriate DVR.
Table 2.8.2. LAN Item Description The fixed IP address of the DVR unit. SUBNET MASK The subnet mask for the LAN GATEWAY The IP address of the Gateway DNS (PRIMARY) The address for the DNS server The address for the DNS server DNS (SECONDARY) 2-8-3.
2-8-4. NETWORK STREAM User can set the Resolution, the frame rate and the quality for a network stream classified by channel. It is recommended that user should adjust each item to proper level to get the network service smoothly. Figure 2.8.4. Network setup screen – Network Stream 2-9.
Table 2.9.1. Config setup Item Description SAVE SETUP User can save the current configuration (Setting values) of DVR to the USB TO A USB memory stick. Put the USB stick on the front panel and press SEL to start the saving process. LOAD SETUP User can upload the configuration of DVR to another DVR using the USB FROM A USB...
Table 2.10.1. Quick Setup Item Description USE QUICK Select the Checkbox to use the Quick Setup. When user inputs the DESIRED DAYS to record, the system displays a SETUP recommended resolution, frame rate, quality and recording type after calculating the capacity of the installed HDD. At that time, the priority is followed by the order of the items;...
Page 48
Icon Description Click the power icon when you want to shut it off by mouse Click the LOCK icon when you want to lock and unlock the DVR by a mouse Click the SETUP icon on the screen using the mouse to see menu items.
Page 49
Indicates that HDD is recycled. Continuous recording in progress. Manual recording in progress. To set the Manual recording mode, press the Record button on the front panel. Motion alarm recording in progress. Sensor recording in progress. Indicates that lock activated, this icon will be back to black color when unlock.
4-2. SEARCH Screen To enter the search screen, select SEARCH menu on the screen using the mouse or press SEARCH icon on live screen. Figure 4.2.1. Search Screen There are 7 ways of search menu such as TIMELINE, EVENT, GO TO FIRST TIME, GO TO LAST TIME, GO TO SPECIFIC TIME, ARCHIVE and LOG on the screen.
When it clicks a Timeline menu, user can see a calendar which has recording data. Select a specific date and time. Use a drag-and-drop function of the mouse control. User can select a specific minutes using a button in the above red box. Press a PLAY button after setting a specific time. Press the PREV to return to the SEARCH window.
4-2-3. Go To First Time You can access from the oldest recorded data on the DVR hard drive by selecting GO TO FIRST TIME on the SEARCH window. Press the PREV to return to the SEARCH window. 4-2-4. Go To Last Time You can access from the last minute recorded data on the DVR hard drive by selecting GO TO LAST TME on the SEARCH window.
4-2-6. Archive Search The ARCHIVE Search window is used to find previously stored video or images. Figure 4.2.4. Archive Search Screen When it clicks an Archive menu, user can see a calendar which has recording data. Select a specific date and then user can see all data.
4-3. Play mode During playback of a recorded event, the mode changes from SEARCH to PLAY. While in PLAY mode, you may return to the SEARCH screen by pressing the X button on the status bar or the ESC button of a remote control.
Press to backup the video. Table 4.3.1. Button functions in PLAY Mode 5. PTZ Control To control the PTZ functions of the camera, select PTZ menu on the screen using the mouse. Select the ◀ ▲ item you wish to control the PTZ camera and control them using the mouse or the control button ( ▶...
Page 56
▶) Press the right key ( on the control button and set the number (3 digits) to go to the preset number. ▶) TOUR Select the TOUR and press the right key ( on the control button. Then, number input window will appear. Set the number (1 digit) using the number key and press SEL to make the group number work.
6. Back up 6-1. Still Image backup onto USB flash memory Still images can be captured and archived onto the USB stick or hard drive in live mode or while playing back recorded video. In live mode, press the BACKUP button to launch the archive function or select BACK UP menu on the screen using the mouse.
Figure 6.2.1. Video Archiving and Backup Screen The DVR will convert the corresponding portion of the video into an AVI file. 6-3. Transferring still images or video from the ARCHIVE list The stored data onto hard drive will be found in the ARCHIVE list in SEARCH window. User can back up still images or video into the storage device from the ARCHIVE list.
Figure 6.3.1. Archive Search Screen 6-4. Playback of Backup Video H.264 format: H.264 format video can be played back by the player (the HD player) that the DVR copies on USB thumb drive with video. Three files are copied on USB thumb drive - H.264 file: H.264 format video file.
7. Upgrading Firmware In order to upgrade, the firmware upgrade file must first be downloaded and copied into the USB memory stick. Create a new folder in the USB memory stick and name it “upgrade”. Copy the firmware upgrade file “xxxxxx.bin”...
Page 61
4. You can see the following progressive message when pressing the upgrade button. 5. You can see the following message when finishing the upgrade. After upgrading, the system should be restarted. At that time, the USB memory stick has to be pulled out. 6.
Page 62
Remote Firmware Upgrade User can upgrade the firmware via Network as follows. 1. Go to the Remote Setup menu on the UMS Multi or Web Viewer. 2. Press the password for admin. Just admin is possible to connect to the remote setup menu.
Page 63
3. Go to the Remote Upgrade menu. Then, you can see the current F/W version as follows. To upgrade a new F/W, insert the F/W in your PC and press the UPGRADE button. 4. Then, you can see the following progress bar and it would be taken around 150 seconds to upgrade. 5.
8. Network access using the Exclusive network viewer, UMS single The DVR provides a live remote monitoring feature. Remote monitoring requires installation of the network viewer on your PC. NOTICE In a high bandwidth network, a maximum of four users can access one DVR simultaneously. In a low bandwidth network it is recommended that only one user access the DVR at a time.
8-2. Installing the network viewer 1. Insert the provided CD in the CD drive and double-click “UMSClient(XXXX).exe” 2. Select a destination folder and click “Next”. 3. Select the type and click “Next”. 4. Select the program folder and click 5. The setup status screen is displayed. “Next”.
Page 66
Button Function Description DATE & TIME Displays the current date and time. CONNECT/DISCONNECT Connect/disconnect network connection. Switches the live mode to search mode. SEARCH DISPLAY MODE Select a channel and screen display mode. PAN/TILT/ZOOM/ FOCUS Control the PAN/TILT/ZOOM/FOCUS features on the remote camera. CAPTURE Capture a still image from live screen.
QUAD/-screen display - Click the QUAD button to switch to quad-screen display Full screen display - Click the maximize button to display only screen and hidden the operation panel. Image capture of live screen Still-image of live screen can be captured and saved as BMP or JPEG file. 1.
8-5. Remote search mode and functions Button Function Description Displays the recording time of the data DATE & TIME selected on the time bar at the bottom of the main user interface. Disconnect network connection.. DISCONNECT LIVE Switches the search mode to live mode. CAPTURE Capture a still image from live screen.
Page 69
PLAYBACK The playback buttons. BUTTON DISPLAY MODE Select a channel and screen display mode. Searching and playing video in the remote DVR Video recorded in the remote DVR or Video recorded on the PC can be searched and played back. 1.
1. Connect the network to the remote DVR and play the video recorded in the remote DVR. 2. Drag the slid on the time scale and drop to the start time for video backup and press the MARK IN button. 3.
Page 71
Security Option: Set a password for security options. When you access any of the selected functions, you will need to enter the password. Save Path: Specify the location to record for backup and still image capture. Automatic reconnection: If a user selects this function, the client S/W will automatically try to connect to the previously connected IP address if the network connection is lost.
Page 72
LOG – Select to save event log into ‘log file’. ICON – Select to display the event on live video. EVENT LIST – Select to show the event in the ‘Event List” window of live mode. Search and check the recorded log data. Setting Record Set the recording conditions and select channels to record.
Select the local disk to use and the amount of disk space you want to allow the program to use for recording. 9. Network access using the Exclusive network viewer, UMS multi 9-1. Overview The UMS Multi-Client is a multiple site monitoring client software with; video, audio, and alarm signals from the DVRs over networks.
9-3. Installing the program 1. Insert the provided CD in the CD drive and double-click “UMSMultiClient (XXXX).exe” 2. Select a destination folder and click “Next”. 3. Select the program folder and click “Next”. 4. The setup status screen is displayed. 5.
9-4. Live Window When installation is completed, double click the “UMS Multi Client” icon on your desktop to start the program. 9-4-1. Main user interface 9-4-2. Control buttons Button Description Click this icon to run a playback window to search and play videos that are recorded in local PC.
Page 76
Click this icon to capture a still image CAPTURE EVENT LIST Click this icon to play/pause live video. PAUSE ALARM ON Enable or disable recording of live video to local disk which has RECORD ON set in setup menu. Use the volume control bar to set the audio level. AUDIO Use the micro phone volume control bar to set the micro phone level.
9-5. Search and Playback Window 9-5-1. Main user interface You can access to search window by clicking the search icon (Local Playback / Remote Playback) on the upper left of Live Window. 9-5-2. Main control panel Button Description Click this icon to run a playback window to search and play videos that are recorded in local PC.
Page 78
Directory window shows site/sites that are pre-registered. Click this icon to connect the selected site/sites. CONNECT Click this icon to disconnect the selected site/sites. DISCONNECT Click this icon to setup configuration of UMS MULTI CLIENT. SETUP Click this icon to capture a still image. CAPTURE EVENT LIST Click this icon to set the beginning time for backup of the...
The calendar shows dates with recorded video in color. To display the recorded data of selected channel or all channels on a time line scale. To change a time line scale from 24 hours to 60 minutes or vise versa. The timeline shows recorded data in color on the bar.
9-6-1. General 9-6-1-1. Security Option: Set a password for security options. Select security options and set a password. Then when you access any of selected functions, you need to enter the password. You can also set the save path for capturing and backup. 9-6-1-2.
9-6-2. Event Event log can be archived and searched. 9-6-2-1. Archiving Event Log: Specify the location to save event logs and select event to archive. 9-6-2-2. Archiving Event Log: Event log can be searched from selected time.
9-6-3. Record 9-6-3-1. Record setup: You can set the recording conditions for Always, Event, or Auto record. And you can also select target DVR/DVRs and channel/channels. When you set the recording condition to event, you can set event for motion or alarm with duration. 9-6-3-2.
9-6-6. About “About” provides network client version information. 9-7. Remote Setup The menu settings for the DVR unit can be set from a PC, via network. Put the cursor of the mouse on the channel which is connected to the site and press the right. Then the following window is displayed.
Page 85
9-7-1. Display User can set the value on this remote setup page. After setting the value, please press the APPLY button. Then the value would be applied to the system without the system rebooting. RELOAD button is used when user want to bring the value in the system.
9-7-7. UPGRADE Please refer to page 54 for the Remote Upgrade. 9-8. Operation 9-8-1. Addition, Delete, and modify of DVR sites 9-8-1-1. Addition of sites 1. Click SITE ADDITION button. And then the following window displays. o Model: User has to select surely a suitable type. SDVR series, H series DVR N series DVR, HD DVR IP Camera...
Page 90
o Site Name: Input a name that properly describes a site. o IP Address: Input IP address (Public IP address of a router that DVR is connected.) or Domain name that is registered at www.okddns.com (for Korea), www.ddnscenter.com (for USA) or www.bestddns.com (for other area including EU) o Port No.: Input port number of DVR.
Page 91
9-8-1-3. Modify of sites 1. Select the site/sites to modify from the directory window. 2. Click NET FINDER button. And then the following window displays. 3. Click MODIFY button. And then the modified information is applied.
9-8-2. Connect and Disconnect 9-8-2-1. Connect 1. Select site/sites to connect from the directory window. 2. Click CONNECT button, and then site/sites displays/display as connected. 9-8-2-2. Disconnect 1. Select site/sites to disconnect from the directory window.
2. Click DISCONNECT button, and then selected site/sites disconnected. 9-8-3. Still-image capture during Live 1. Double-click a channel to capture from the display screen. (Otherwise all channels will be captured.). 2. Click CAPTURE button. And then a Capture window displays. 3.
9-8-4. Recording video on local PC during Live 1. Click SETUP button. And then a setup window display. 2. Select Record and set the values. 3. Select Disk and set the values.
4. Click RECORD ON button. And the color of button is changed. 5. Live video data is recorded as set in Record and Disk setup. These video data can be searched and play-backed with Local Playback. 9-8-5. Local Playback and Remote Playback 9-8-5-1.
Page 96
5. Video data that is recorded on local PC will be play-backed. 9-8-5-2. Playback of recorded video on remote DVR 1. Click REMOTE PLAYBACK button. And then Playback Window display over Live Window. 2. Select site to connect from the directory window. 3.
5. Video data that is recorded on a remote DVR is play-backed. 9-8-6. AVI Backup during playback You can back up the recorded videos in AVI format during playback. 1. Double-click the target channel to backup. 2. Select the beginning time by using the search calendar and slide bar. 3.
Page 98
5. Click BACKUP. And then the window appears as below. 6. You can also set the beginning time and ending time on this window. After selecting a channel for backup, click the OK button. The backup will begin. 8. AVI video data is recorded as set in AVI Backup window. AVI format video can be played back by Window Media Player™...
10. Network – By an web-browser viewer The DVR provides a live remote monitoring feature by web-browser viewer. 1. Check the IP address of the DVR from SETUP>SYSTEM>DESCRIPTION>IP ADDRESS. 2. Input the IP address or Domain name address that you pre-registered on www.bestddns.com on the address field and press “Go”.
Page 100
5. Web Browser Viewer is displayed as bellow. 6. Click CONNECT button on the Left upper corner of web-viewer. Then “Connect” dialog is displayed. Enter IP address (or Domain name address that you pre-registered on www.bestddns.com, www.okddns.com or www.ddnscenter.com, Port number and Password and click “Connect” Server address: Input IP address of the DVR from SETUP>SYSTEM>DESCRIPTION>IP ADDRESS or Domain name address that you pre-registered on www.bestddns.com, www.okddns.com or www.ddnscenter.com,...
Page 101
Port: Input Port number (The number is set on SETUP>NETWORK>PORT.) ID: Input ID of DVR. Password: Input network password of DVR. (The number is set on SETUP>SYSTEM>NETWORK PASSWORD.) 7. Then the cameras connected to the DVR are displayed on the screen. 8.
APPENDIX: How to connect network A. How to set IP address of the DVR and open TCP port of the router? The port forwarding is dependent on the brand and model of the router. The port forwarding is required to allow access to the DVR beyond a router.
Page 103
Open your web browser. Enter the router IP address in the address bar (The router IP address are different with the brand and model.), click GO. 4. Enter the user name and password (admin is default) and press the OK button. 5.
Page 104
Network access beyond a router In order to access the DVR remotely beyond a router (firewall), the user must open TCP port for command level, live channels and storage channels. User need to open 2ports numbers on the router; the DVR port number 5445 and the WEB port number 80. If this port is not opened properly, user can not access DVR beyond a router.
Page 105
B. How to access DVR from Remote PC? LAN Connection – Using a switching hub Connect to the system, using a hub (Switching hub) and an Ethernet cable (10BASE-T/100BASE-TX CAT 5 LAN cable) 1. Run the pre-install the network client software on the supplied CD. (Refer to Chapter 6. Network access using the Exclusive network viewer) 2.
Page 106
1. Go to SETUP>NETWORK. Set NETWORK TYPE as DHCP and DDNS SERVER as ON. And select one type among bestddns.com, okddns.com and ddnscenter.com after setting to DDNS1. 2. Go to Setup menu of Router and open TCP port 5445 and 80 using Port Forwarding. (Refer to A. How to set IP address of the DVR and open TCP port of the router?) 3.
Page 107
Model: Select one type surely among SDVR series, H DVR series DVR / N series DVR, HD DVR / IP Camera. Site Name: Input the name of the DVR. Site Address: Input the Domain Name that is registered on http://www.bestddns.com. Please log on http://www.okddns.com in Korea and http://www.ddnscenter.com in USA.
Page 108
C. How to access DVR with iPhone? 1. Run App Store. 2. Search “iums” 3. Touch “iums” icon. 4. Install “iums” 5. Run “iums” icon. 6. Touch “+” icon. 7. Input the information. 8. Touch “Save” icon. 9. Touch the added site. 10.
Page 110
D. How to access DVR with Android? 1.Run Android Market. 2. Search “iUMS” 3.Search “iUMS”. 4.Install “iUMS”. 5. Run “iUMS” 6. Register user. 7. Touch Live View. 8. Add the Site or Device. 9. Select Channels.
Page 112
® is a registered trademark of Videor E. Hartig GmbH Exclusive distribution through specialised trade channels only. Videor E. Hartig GmbH Carl-Zeiss-Straße 8 · 63322 Rödermark, Germany Tel. +49 (0) 6074 / 888-0 · Fax +49 (0) 6074 / 888-100 www.videor.com...
Need help?
Do you have a question about the HDR-4008AE3.0 and is the answer not in the manual?
Questions and answers