Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for advidia P-240
Summary of Contents for advidia P-240
-
Page 1: Installation Guide
Installation Guide Included Installation Instructions Network Camera P-240 Model No. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual. - Page 2 For U.S.A WARNING: This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply. • To prevent injury, this apparatus must be securely attached See www.dtsc.ca.gov/hazardouswaste/perchlorate/ to the wall/ceiling in accordance with the installation instruc- tions.
-
Page 3: Table Of Contents
Contents Important safety instructions ............................. 4 Limitation of liability ................................5 Disclaimer of warranty ............................... 5 Preface ....................................5 Main functions ................................... 6 About the user manuals ..............................7 System requirements for a PC ............................7 Trademarks and registered trademarks..........................8 Copyright ................................... -
Page 4: Important Safety Instructions
Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 6) Only use attachments/accessories specified by the manufacturer. -
Page 5: Limitation Of Liability
THE CORRESPONDING PRODUCT (S). Disclaimer of warranty IN NO EVENT SHALL advidia BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW: (1) ANY LOSS OR DAMAGE, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT;... -
Page 6: Main Functions
Main functions H.264 dual stream and JPEG (MJPEG) triple encoding H.264 dual stream output and JPEG (MJPEG) output can be simultaneously provided. * H.264 stream1: 1920x1080/ max. 30 fps H.264 stream2: 640x360/ max. 30 fps Super Dynamic (MEGA Super Dynamic) (☞... -
Page 7: About The User Manuals
About the user manuals There are 2 sets of operating instructions for the P-240 as follows. • Installation Guide: Explains how to install and connect devices, as well as how to connect and configure the network. • Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how to operate this camera. Adobe ® Reader ® is required to read these operating instructions on the provided CD-ROM. When the Adobe Reader is not installed on the PC, download the latest Adobe Reader from the Adobe web site and install it. -
Page 8: Trademarks And Registered Trademarks
Trademarks and registered trademarks • Microsoft, Windows, Windows Vista, Windows Media, Internet Explorer, and ActiveX are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation. • Intel and Intel Core are trademarks of Intel Corporation in the U.S. and other countries. • Adobe, Acrobat Reader, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. • SDXC Logo is a trademark of SD-3C, LLC. • iPad, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. • Android is a trademark of Google Inc. • All other trademarks identified herein are the property of their respective owners. Copyright Distributing, copying, disassembling, reverse compiling and reverse engineering of the software provided with this product are all expressly prohibited. -
Page 9: Precautions
Precautions The exclusively designed mount bracket shall be Refer installation work to the dealer. Installation work requires technique and experience. used. Failure to observe this may cause fire, electric shock, Failure to observe this may cause a drop resulting in injury or accidents. - Page 10 Do not damage the power cable. When an error is detected, this product will restart Do not damage, fabricate, twist, stretch, bundle, or forci- automatically. bly bend the power cable. Do not place heavy objects on This product will be inoperable for around 2 minutes after it, and keep it away from heat sources.
- Page 11 Transmission interval About the MOS image sensor Image transmission interval may become slow depending • When continuously shooting a bright light source on the network environment, PC performance, shooting such as a spotlight, the color filter of the MOS image subject, access number, etc.
- Page 12 Lens and pan/tilt head If a lens and pan/tilt head are not performed for a long period of time, the grease coating inside these parts may become sticky. That may obstruct the parts from moving. To prevent this, move the lens or pan/tilt head periodically. Or perform position refresh periodically in the manner described in “Position refresh”.
-
Page 13: Precautions For Installation
Precautions for installation Advidia assumes no responsibility for injuries or Protection from lightning property damage resulting from failures arising out When cables are used outdoors, there is a chance that of improper installation or operation inconsistent they may be affected by lightning. In such a case, install a with this documentation. - Page 14 Radio disturbance Check before installation When this product is used near TV/radio antenna, strong Compatibility of devices is restricted. Before installation, electric field or magnetic field (near a motor, a transformer check the ratings and dimensions of the devices to be or a power line), images may be distorted and noise may used.
-
Page 15: Major Operating Controls
Major operating controls <Main body> Power cable Brown To the power supply (24 V AC, 50 Hz/60 Hz) Blue Green External I/O cable Microphone input cable (connector: white) Audio output cable (connector: black) Network cable with cable coupler Output cable for the monitor used for adjustment Safety wire Attachment pipe Housing base (inside) - Page 16 <Rear view of the main body with the main sunshield rear cover detached> Main nameplate Water-resistant cap Link indicator Access indicator INITIAL SET switch (OFF ⇔ ON) Live indicator SD memory card slot...
-
Page 17: Initialize The Camera
Initialize the camera Use the INITIAL SET switch to reset the settings of the camera to the default. IMPORTANT: • The settings including the network settings will be initialized. Note that the preset position settings and the CRT key (SSL encryption key) used for the HTTPS protocol will not be initialized. Step 1 Step 5 Pull out the water-resistant cap by following steps 1 - 3 of Move the INITIAL SET switch to the left (OFF). the “How to insert an SD memory card”... -
Page 18: Insert/Remove An Sd Memory Card
Insert/remove an SD memory card How to insert an SD memory card IMPORTANT: • When inserting an SD memory card, make sure the direction. Step 1 Step 3 Pull out the main sunshield rear cover on the rear of the Turn the water-resistant cap to the “OPEN” side, and pull camera by pressing the tab on the top of the sunshield. -
Page 19: How To Remove The Sd Memory Card
Step 5 Step 7 Align “△” of the water-resistant cap to “OPEN ▽” of the First, insert the tab on the bottom of the main sunshield camera. Then, turn the water-resistant cap toward “▽ rear cover into the main body, and then push the tab on LOCK”... -
Page 20: Installations/Connections
Installations/Connections Caution: • O NLY CONNECT 24 V AC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/ UL/CSA 60950-1). Before installation, prepare the following • When mounting this camera to a ceiling, mount it using a custom-made ceiling mount bracket and the attachment pipe (attached to the camera). Refer to page 22 for the specifications of the custom-made ceiling mount bracket. • When mounting the camera to a wall, mount it using a custom-made wall mount bracket and the attachment pipe (attached to the camera). - Page 21 How to detach the housing base Before attaching a custom-made mount bracket, detach the housing base and attachment pipe from the camera so that installation and connections can be performed. Step 1 Step 2 Remove the fixing screws (3 pcs.*) that are securing the To separate the housing base from the camera, turn the housing base and the camera.
- Page 22 Installation Before starting installation/connection, make sure that the power cable is not connected to the main power supply. Refer to the “Precautions for installation” section before starting installation/connection. (☞ page 13) ② Fix the attachment pipe to the bracket. Step 1 Install the mounting bracket.
- Page 23 ③ Connect the safety wire (comes with the camera) to the Step 4 mount bracket. Mount the camera to the bracket. Refer to the operating instructions of each mount ① Attach the housing base to the mount bracket using bracket for further information about where to con- the hexagon screws (M5, 4 pcs.) attached to the nect the safety wire.
- Page 24 ③ Joint both sides of front and rear sunshields. Fixing screws (3 pcs.) Joint the hook and dent on the linked side, and then joint the other side. Front and rear sunshields Housing base Positioning pin Main sunshield Camera Safety wire IMPORTANT: • Joint both sides of the front and rear sunshields before fitting in the main sunshield.
- Page 25 (Refer to the illustration). Model No. Protection Cover P-240 PGKV1116 *1 Note that foreign objects may be mixed into water depending on the container, and it may result in reducing the effectiveness of the rain wash coating. Do not use the spray bottle equipped with a handle or a function to adjust...
- Page 26 Connection Caution: • B efore starting connections, make sure that the power connection (24 V AC power cord or LAN cable) is discon- nected. Failure to observe this may cause fire, electric shock, injury, or damage to the product. • A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED TO THE EQUIPMENT POWERED BY 24 V AC POWER SUPPLY.
- Page 27 • 24 V AC power supply connector kit (accessory) • Network cable Recommended specification of cable (wire) Connect a LAN cable (category 5e or better) to the net- work connector. AWG size (stranded (0.22 mm (0.33 mm (0.52 mm (0.83 mm IMPORTANT: wire) • Use all 4 pairs (8 pins) of the LAN cable.
- Page 28 • External I/O cable Note: • Make sure that the stereo mini plug is connected to this cable. When a monaural mini plug is connected, IMPORTANT: audio may not be heard. • Off, input, and output of the external I/O terminal 2 When connecting a monaural speaker with amplifier, and 3 can be switched by configuring the setting.
-
Page 29: Connection Example
Connection example (Refer to page 26 for how to connect the cables.) When connecting with a PC directly RJ45 female connector (cable coupler) Powered speaker LAN cable (category 5e or better, cross) Power supply Plug-in power type (24 V AC) microphone Recommended total extended cable length*... - Page 30 Connecting to a network using a PoE+ hub when the temperature is –30 °C {–22 °F} or less * When connecting to a network using a PoE+ hub when the temperature is –30 °C {–22 °F} or less, use a 24 V AC power supply or a tested PoE injector.
-
Page 31: Configure The Network Settings
Configure the network settings Configuring the camera so that it can be accessed from a PC The following are descriptions for when the camera with default settings is configured. If you are using firewall software on your PC, the Setup Program may not be able to find any cameras on your network. Configure the setting of the camera after temporarily invalidating the firewall software. - Page 32 (The viewer software is installed from the camera.) • The “Live” page will be displayed. • If you cannot install the viewer software “Advidia WebViewer Plugin” or if images are not displayed, click the [Install] button next to [Viewer Software] on the launcher window to install the software.
-
Page 33: Troubleshooting
Troubleshooting Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below. Reference Symptom Cause/solution pages When using a PoE+ device for power supply... - Page 34 Reference Symptom Cause/solution pages • UPnP error has occurred since the power is not supplied to the router. − Turn on the power of the router. Wait until the connections are established. • An error has occurred during the port update by the UPnP func- Live indicator keeps on Operating tion. blinking orange approx. in Instructions If the router in use does not support the UPnP function, perform 2 seconds intervals.
- Page 35 Reference Symptom Cause/solution pages The effectiveness of the rain wash coating may have been It is hard to see images with reduced. Refer to “Cleaning this product body” in “Precautions for the camera when there are use” and clean the dome cover. If the situation does not improve raindrops on the dome cover.
-
Page 36: Specifications
Specifications Basic • Power source: AC 24 V, PoE+ device (IEEE802.3at compliant) or Tested PoE injector (60 W) Power consumption : AC 24 V: 3.5 A/Approx. 55 W Tested Power over Ethernet (Injector: 60 W) DC 54 V: 1.0 A/Approx. 50 W PoE+ DC 54 V: 470 mA/Approx. - Page 37 Super-Dynamic: On/Off Dynamic range: 52 dB typ. (Super Dynamic: On) Face SD: On/Off Gain (AGC): On (High)/ On (Mid)/ On (Low)/ Off Adaptive black stretch: On/Off Back light compensation (BLC): On/Off Fog compensation: On/ Off Light control mode setting: Outdoor scene/ Indoor scene (50 Hz)/ Indoor scene (60 Hz)/ Fix shutter Shutter speed: Off (1/30), 3/100, 3/120, 2/100, 2/120, 1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000...
- Page 38 • Network Network: 10BASE-T/100BASE-TX, RJ45 connector Resolution: • When “2 mega pixel [16:9]” is selected for “Image capture mode” H.264 1920x1080/640x360/320x180, max. 30 fps JPEG (MJPEG) 1920x1080/640x360/320x180, max. 30 fps • When “1.3 mega pixel [16:9]” is selected for “Image capture mode” H.264 1280x720/640x360/320x180, max. 30 fps JPEG (MJPEG) 1280x720/640x360/320x180, max. 30 fps • When “1.3 mega pixel [4:3]” is selected for “Image capture mode” H.264 1280x960/VGA/QVGA, max. 30 fps JPEG (MJPEG) 1280x960/VGA/QVGA, max. 30 fps Image compression method: Transmission priority: H.264*...
-
Page 39: Standard Accessories
*5 Use the SD memory card that complies with UHS-1(Ultra High Speed-1) in the case of SD Speed Class 10. *6 For further information about compatible devices, refer to our website (http://advidia.com/cameras/). Standard accessories Installation Guide (this document) ........................1 pc. - Page 40 5120 Woodway, Suite 5006 Houston TX, 77056 (832) 240-1768 http://advidia.com/ © advidia 2015 avs0615-0 PGQX1917ZA Printed in China...